Brand:

AUMA SA 25.1 Multi-Turn Actuator

Description

Overview

AUMA SA 25.1 is an AUMA NORM multi-turn actuator for open-close duty with a tripping-torque window of 630 to 2,000 Nm and 12 output speeds from 4 to 180 rpm. SA 25.1 opens the heavy end of AUMA’s SA range. It delivers 630 to 2,000 Nm on an F25 flange with a 95 mm stem bore, and it is quoted at 150 to 160 kg, so it is handled with lifting equipment rather than by hand.

Operating Principle

The SA 25.1 counts motor turns to stop at the OPEN and CLOSED limits and trips on torque in each direction between 630 and 2,000 Nm. Duty is S2 – 15 min as standard, with S2 – 30 min as an option, and the actuator holds the valve by self-locking up to 90 rpm.

Engineering Design of the AUMA SA 25.1

Output speed and torque are linked: 2,000 Nm is available up to 90 rpm, 1,700 Nm at 125 rpm and 1,400 Nm at 180 rpm in S2-15 min duty. The actuator is self-locking up to 90 rpm only. AUMA also publishes separate data for brake-motor and hydraulic-steel-structure versions of this size range, which are worth consulting for gate and weir applications.

Key Features

What stands out on the AUMA SA 25.1:

  • Heavy-duty multi-turn actuator for large valves and gates.
  • Tripping torque is adjustable in each direction from 630 Nm to 2,000 Nm (ratio 3.2 : 1).
  • The permitted torque falls to 1,400 Nm for S2 – 30 min duty, 70 percent of the 2,000 Nm maximum.
  • With 150 to 160 kg of weight, it delivers 12.5 to 13.3 Nm per kilogram at maximum torque.
  • An illustrative stroke of 60 turns takes about 112 seconds at 32 rpm.
  • Step down to the SA 16.2 for lighter valves or up to the SA 30.1 for heavier ones.
  • AUMA keeps dimensional and electrical details in separate sheets rather than in the technical data.

Selecting the AUMA SA 25.1

Moving up from the SA 16.2 the engineering changes: the family designation switches from the .2 to the .1 generation, the standard housing protection becomes IP67 with IP68 as an option, the number of permitted starts drops from 60 to 40 per hour, and the F-flange jumps from F16 to F25. The torque window starts at 630 Nm, so the AUMA SA 25.1 should not be applied to valves with a seating torque far below that value. The speed range of 4 to 180 rpm keeps the familiar twelve ratios, although 4 and 5.6 rpm are only available on request.

Typical partners are large gate and globe valves in main process and water lines, big rising-stem sluice gates and penstocks, and heavy knife-gate valves. The same actuator can drive AUMA gearboxes for large quarter-turn butterfly valves where the valve manufacturer specifies a multi-turn input.

From this size onward the AUMA documentation separates the actuator into AUMA NORM versions, with motor connection compartment, and versions with integral actuator controls. A common configuration for the AUMA SA 25.1 is an actuator with AC controls, where limit and torque settings are made through the controls and, with the optional magnetic limit and torque transmitter, without opening the housing. If a plant already standardises on AC controls, confirm the supply voltage and frequency before ordering: the standard voltages run from 220 V to 500 V at 50 or 60 Hz, and special voltages up to 690 V are available.

Sizing example for the AUMA SA 25.1

Consider an illustrative sluice gate that needs 1,100 Nm to unseat and 650 Nm to run. A 25 percent margin gives about 1,375 Nm, inside the 630 to 2,000 Nm window of the AUMA SA 25.1. At 125 rpm the S2-15 min torque is 1,700 Nm and at 180 rpm 1,400 Nm, so even the faster ratios would still cover this duty. A 60-turn stroke at 11 rpm takes about 327 seconds, at 22 rpm about 164 seconds and at 45 rpm about 80 seconds. These numbers are an illustrative calculation and not AUMA data.

Installation and Mounting of the AUMA SA 25.1

At 150 to 160 kg the AUMA SA 25.1 is lifted with a crane or chain hoist and the valve or gate structure must be verified for the weight and the reaction torque. The F25 flange takes a rising stem up to 95 mm. Because the standard enclosure is IP67, specify IP68 when the actuator may be flooded, and route cables so that water cannot run into the separate motor terminal compartment.

Industrial Applications

In Oman the AUMA SA 25.1 is specified for intake and outfall valves at coastal power and desalination stations, for bulk-water transmission and reservoir inlet valves, and for large isolation valves at refineries and port terminals such as Sohar, Duqm and Salalah. Where flooded chambers are possible the optional IP68 enclosure should be requested, since the standard version is rated IP67.

Projects often pair the SA 25.1 with the AUMA SA 07.2 multi-turn actuator, the AUMA MATIC AM/AC integral actuator controls and the AUMA SAREx explosion-proof modulating actuator, all available from Seven Star LLC as trusted AUMA supplier.

Neighbouring sizes and counterparts: AUMA SA 16.2 multi-turn actuator, AUMA SA 30.1 multi-turn actuator, AUMA SAR 25.1 modulating actuator and AUMA SAEx 25.1 explosion-proof actuator.

Technical Specifications

Data of the AUMA SA 25.1 from the AUMA technical data sheet for 3-phase AC motors.

Parameter Specification
Model AUMA SA 25.1
Setting range, S2 – 15 min 630 to 2,000 Nm
Top torque S2 – 30 min 1,400 Nm
Torque loss at top speeds 1,700 Nm at 125 rpm and 1,400 Nm at 180 rpm (S2-15 min); 1,200 Nm and 1,000 Nm (S2-30 min)
Start limit per hour 40
Available speeds 4 to 180 rpm at 50 Hz, 4.8 to 216 rpm at 60 Hz, 12 steps (4 and 5.6 rpm on request)
Valve interface EN ISO 5210 F25; DIN 3210 G4
Largest rising stem 95 mm
Handwheel diameter 400 mm
Approximate weight 150 to 160 kg
Ingress protection IP67 (IP68 optional)
Self-locking range up to 90 rpm (50 Hz) / 108 rpm (60 Hz)

Setpoint guide for the SA 25.1 (illustrative calculation, not AUMA data)

Breakaway torque (Nm) Setpoint at +25 percent (Nm)
504 630
700 875
900 1,125
1,100 1,375
1,300 1,625
1,600 2,000

Stroking time for 60 turns at the SA 25.1 (illustrative calculation, not AUMA data)

rpm at 50 Hz rpm at 60 Hz Seconds for 60 turns at 50 Hz
4 (on request) 4.8 900
5.6 (on request) 6.7 643
8 9.6 450
11 13 327
16 19 225
22 26 164
32 38 113
45 54 80
63 75 57
90 108 40
125 150 29
180 216 20

Request a Quote for AUMA SA 25.1

The AUMA SA 25.1 can be quoted within days once we have your valve torque, the F25 interface details and the preferred controls. Download the AUMA datasheet from this page, then contact the Seven Star LLC instrumentation division in Muscat.

Datasheets & Documents
  • PDF Datasheet AUMA SA 25.1 - SA 48.1 Technical Data Sheet (covers AUMA SA 25.1) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

AUMA builds electric actuators for industrial valves, gates and dampers. The company was founded in 1964 near Stuttgart by Werner Riester and Rudolf Dinse, moved its headquarters to Müllheim in south-west Germany in the early 1970s, and still trades as the owner-managed AUMA Riester GmbH & Co. KG. Its actuators run isolation and control valves in water, power, oil and gas and process plants worldwide.

Seven Star LLC is an independent supplier listing AUMA multi-turn and part-turn actuators, actuator controls, gearboxes and spare parts for buyers in Oman and the GCC. We work from the nameplate data so that a replacement matches the installed actuator, controls and gearbox.

AUMA company profile

Origin Founded in 1964 by Werner Riester (engineering) and Rudolf Dinse (sales and finance); registered as Riester KG in Esslingen. Water and wastewater plants were the first customers.
Headquarters Müllheim, Baden-Württemberg, Germany (since the early 1970s). Production in Germany, with further plants in India, the USA and China, and around 30 sales and service companies worldwide.
Ownership Privately held, owner-managed company: AUMA Riester GmbH & Co. KG
Torque and thrust range Multi-turn, part-turn and linear actuators from 1.5 Nm to 675,000 Nm with gearboxes, and linear thrust up to 217 kN, as published by AUMA
Design principle Modular: actuator, integral controls and gearbox are combined to suit the valve, so one actuator size can serve open-close, modulating, fieldbus or explosion-proof duty

Milestones

  • 1964: Werner Riester and Rudolf Dinse found AUMA near Stuttgart; the first actuator range follows, with water and sewage plants as the first customers.
  • Early 1970s: Lack of space in Nellingen leads to the move to Müllheim in south-west Germany.
  • 1974: AUMA Benelux, the first foreign subsidiary, is founded.
  • Today: About 2,800 employees worldwide, around 850 of them in Müllheim, according to AUMA.

AUMA actuator, controls and gearbox series

Series Type Typical use
SA 07.2 to SA 16.2, SA 25.1 to SA 40.1 Multi-turn actuators, open-close duty Gate and globe valves, sluice gates and penstocks; SA 07.2 to 16.2 cover roughly 10 to 1,000 Nm, the .1 sizes go far higher
SAR 07.2 to SAR 30.1 Multi-turn actuators, modulating duty Control valves that receive a continuous position setpoint and many starts per hour
SAV, SARV, SQV, SQRV Variable-speed actuators Slow approach to the seat to limit water hammer, fast travel elsewhere
SQ 05.2 to SQ 14.2, SQR Part-turn actuators Ball, butterfly and plug valves and dampers, about 50 to 2,400 Nm; SQR for modulating duty; FQM fail-safe unit for spring-return action
SAEx, SAREx, SQEx, PROFOX-MX, TIGRON Explosion-proof actuators Hazardous areas in oil, gas and chemical plants, with ATEX and IECEx certified versions
AUMA MATIC AM, AUMATIC AC, ACExC 01.2, AMExC 01.1, AC 01.2-SIL Integral actuator controls AM for simple parallel wiring; AC for positioning, diagnostics and fieldbus (PROFIBUS DP, PROFINET, Modbus, FOUNDATION Fieldbus, HART depending on version); SIL version for safety functions
GS, GHE, SA + GS combination Part-turn worm gearboxes Large butterfly and ball valves, from GS 63.3 up to GS 630.3 at 675,000 Nm
GK, GST, GHT, GP Multi-turn gearboxes (bevel, spur, worm, planetary) Offset or right-angle drives and very high multi-turn torque
LE, SVC/SVCR, PROFOX-L Linear actuators and thrust units Globe and control valves with a rising stem, up to 217 kN
PROFOX-M, PROFOX-Q Compact smart actuators Small valves where a full SA or SQ is oversized
SA-UW, SGM/SGMR, SVM/SVMR, SAN/SARN Special versions Submerged valves, seawater-exposed ship and offshore duty, nuclear plant service
SIMA2 Master station Fieldbus network management for many actuators on one plant

Where AUMA actuators are used

Water transmission and treatment is the largest use: pipeline isolation valves, pumping stations, desalination plants and sluice gates. AUMA actuators also run valves in power plant steam, feedwater and cooling systems, pipelines and tank farms, refineries and chemical plants, and on ships and offshore platforms. In the Gulf, check the ambient temperature rating, since actuators in direct sun can exceed 50 °C, and specify the enclosure protection for sand and humidity.

Ordering AUMA actuators and spare parts: what we need

For a replacement, send photos of the actuator, motor and controls nameplates: type designation, commission or order number, serial number and wiring diagram number. AUMA identifies the original build from the commission number. For a new actuator, add the valve type, required torque or thrust at the worst case, number of turns or swing angle, operating time, mounting flange to ISO 5210 or ISO 5211, stem or shaft dimensions, duty (open-close or modulating), supply voltage and frequency, control signals or fieldbus, and the hazardous-area marking required on site.

Facts checked against AUMA product information and the company history published by AUMA, October 2026.

FAQ

Questions about the AUMA SA 25.1 Multi-Turn Actuator

Answers from our engineering team on installation, compatibility and integration.

01What is the torque range of the AUMA SA 25.1?
The tripping torque of the AUMA SA 25.1 is adjustable between 630 and 2,000 Nm in S2 - 15 min duty, and the S2 - 30 min maximum is 1,400 Nm. Torque is reduced at the highest speeds: 1,700 Nm at 125 rpm and 1,400 Nm at 180 rpm (S2-15 min); 1,200 Nm and 1,000 Nm (S2-30 min).
02Which output speeds and starts per hour does the AUMA SA 25.1 offer?
The AUMA SA 25.1 offers 12 output speeds from 4 to 180 rpm at 50 Hz and up to 40 starts per hour, and it is self-locking up to 90 rpm (50 Hz) / 108 rpm (60 Hz). An illustrative valve needing 60 turns takes about 112 seconds at 32 rpm.
03Which valve flange and stem size does the AUMA SA 25.1 fit?
The AUMA SA 25.1 uses an EN ISO 5210 F25 flange (DIN 3210 G4 optional) with a rising-stem capacity of 95 mm. Special output drives AF, AK, AG, B3D, ED, DD as well as IB1 or IB3 are quoted for this size; the IB variants are limited to the SA 25.1 and are on request for larger sizes.
04When should I choose the AUMA SA 25.1 instead of a neighbouring size?
Select the AUMA SA 25.1 when the valve needs about 630 to 2,000 Nm. For 400 to 1,000 Nm the SA 16.2 is smaller and lighter, while loads between 1,250 and 4,000 Nm are handled by the SA 30.1 on the F30 flange.
05Is Seven Star LLC a trusted supplier for AUMA products?
Yes. Seven Star LLC supplies genuine AUMA products across Oman and the GCC. The AUMA SA 25.1 is supplied as genuine AUMA product with documentation and regional technical support from our Muscat team.