Brand:

JUMO hydroTRANS S10 Indoor RH, Temperature and CO2 Transmitter

Description

A wall-mounted indoor air quality transmitter with optional CO2 module

The JUMO hydroTRANS S10 (type 907045) monitors indoor air quality by measuring relative humidity and temperature and, optionally, carbon dioxide. It is made for wall mounting at weather-protected locations and is aimed at building automation, climate monitoring, public indoor spaces and offices. The device is available with or without a 1.77 inch TFT display that shows up to three process values, and it has analog outputs or a Modbus RTU RS485 interface plus a USB port for setup. Calculated values such as dew point, frost point, wet-bulb temperature, absolute humidity, mixing ratio, partial water vapour pressure and specific enthalpy can also be output, which helps HVAC engineers control comfort and condensation risk.

Technical specifications

Parameter Specification
Type 907045 hydroTRANS S10; extension 11 RH and temperature, 12 RH, temperature and CO2
Relative humidity 0 to 100 % RH (0 to 95 % RH with CO2 module); typical ±2.0 % RH, maximum ±2.5 % RH after 60 h stabilisation
Temperature -5 to +55 °C, accuracy ±0.4 °C
CO2 (optional) 400 to 10,000 ppm; ±(50 ppm + 5 % of reading); sampling 30 s
Sampling 1 s for humidity and temperature
Calculated values Dew point, frost point, wet-bulb temperature, absolute humidity, mixing ratio, vapour pressure, specific enthalpy
Current output 4 to 20 mA, limits 0 to 22 mA, ±0.1 % of 20 mA, load up to 500 Ω
Voltage output 0 to 10 V, limits 0 to 11 V, ±0.1 % of 10 V, load 10 kΩ or more
RS485 Modbus RTU, addresses 1 to 254, 9600 to 115200 baud, response time 0 to 500 ms
USB Micro-B USB 2.0 for setup software, cable up to 5 m
Supply DC 24 V SELV or PELV; power up to 2.4 W
Display TFT 1.77 in., 128 x 160 pixels, 11 brightness levels
Housing PC housing with PMMA display cover; about 81 g
Terminals Screw terminals, 0.08 to 4.5 mm2
Protection IP20 (front); climate class 3K22; humidity up to 90 % non-condensing
Ambient temperature -5 to +55 °C; storage -25 to +60 °C; altitude up to 2000 m
Vibration CO2 module is sensitive to vibration; 0.15 mm at 10 to 58.1 Hz

Choosing the variant

Pick extension 11 for humidity and temperature or extension 12 when carbon dioxide is also needed for demand-controlled ventilation. The analog version delivers its signals on screw terminals 3, 4 and 5 with the analog ground on 6, and the RS485 version lists the bus lines A and B on terminals 1, 2, 4 and 5, with an optional ground. With the CO2 module, the maximum humidity measurement range falls to 95 % RH, and the CO2 element is sensitive to vibration, so do not mount the device on a vibrating machine.

The order code is 907045 / extension – version – measuring range – output / extra code. Measuring range 33 gives 0 to 95 % RH and -5 to +55 °C, and range 18 adds a 5000 ppm CO2 range. Output 009 is a configurable 4 to 20 mA or 0 to 10 V combination output, and output 530 is RS485 Modbus. Extra code 994 adds the integrated display, and 775 is a DAkkS calibration service with test points stated in plain text. Stock versions carry part numbers from 30049450 to 30049524, for example 907045/11-0-33-009/994 with display as 30049472.

Installation notes

The transmitter is for indoor use only, with an IP20 front, so it should not be installed where water spray, dust or condensation reaches it. Dimensions of the housing are 81 x 85 mm with a depth of 25 mm without a display or 27 mm with a display. The scope of delivery includes the device, brief instructions and three fastening screws, while the USB cable A to Micro-B (00616250) and the hydroTRANS setup program (00775170) are accessories. The startup display shows the device name, software version, hardware version and TAG number for about five seconds. Mount it on a wall away from direct sunlight, supply air outlets and heat sources, and allow 60 hours after first start-up before judging humidity accuracy. Use conductors of 0.08 to 4.5 mm2 stripped by at least 6 mm, rated for at least 80 °C, and for UL applications use the approved cable types listed in the datasheet, which must also suit the voltage, current and temperature. For commissioning, connect the USB port to a PC to change the output scaling, the Modbus address and the displayed values. In offices, hospitals, classrooms, mosques and shopping malls in hot climates, CO2 and humidity control reduces over-ventilation and saves cooling energy.

See temperature instrumentation for related items.

Using the hydroTRANS S10 in Oman and the GCC

Indoor air quality transmitters are used in the region in offices, schools, hospitals, malls, hotels and data rooms, where air conditioning runs for most of the year. Measuring humidity, temperature and CO2 allows building management systems to control fresh air intake, which saves energy while keeping indoor air comfortable. CO2 control is particularly useful in rooms with variable occupancy, such as meeting rooms and classrooms.

Mount the transmitter on an inside wall at a representative height, away from air conditioning outlets, direct sun, doors and heat sources. Check that the output type, analog or Modbus, matches the building management system. Humidity and CO2 sensors should be checked at regular intervals to keep readings reliable.

For larger buildings, a room-by-room list with the required measured values and output type helps keep the order consistent, and it lets us confirm that the transmitters suit the building management system that will read them. Send the list with the enquiry where possible.

Information to send with an enquiry

  • Measured values needed, with or without CO2
  • Display or no display
  • Output type: analog or Modbus RTU
  • Supply voltage and quantity

Related JUMO products: JUMO hydroTRANS S30 Duct Humidity and Temperature Transmitter, JUMO hydroTRANS S20 Wall-Mount Humidity and Temperature Transmitter, JUMO dTRANS T07 Two-Channel HART Temperature Transmitter, JUMO hydroTRANS H50 Industrial Humidity and Temperature Sensor, JUMO Wtrans E01 Wireless Humidity, Temperature and CO2 Probe and JUMO dTRANS T100 Screw-In RTD Temperature Probe.

Documents and quotation

The hosted document is JUMO data sheet 907045 (10 pages, English). It includes dimensions, terminals and order details. Confirm variant, output and display before ordering. Seven Star LLC is an independent supplier in Muscat; send the room type and signals needed for a quotation. To help us prepare an accurate quotation, please include the medium, temperature and pressure range, required output signal, process connection and supply voltage, together with the quantity needed and the delivery location. We will then compare these details with the order information in the datasheet.

Datasheets & Documents
  • PDF Datasheet JUMO 907045 data sheet 907045 (EN) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

JUMO is the German maker of temperature sensors, process controllers, pressure transmitters and liquid analysis instruments. Moritz Kurt Juchheim founded it in Fulda in 1948 as M. K. Juchheim KG, making glass thermometers with six employees. The name JUMO comes from the founder's name. It is still a family company headquartered in Fulda, and the parent company has been called JUMO GmbH & Co. KG since 2003.

Seven Star LLC is an independent supplier in Muscat. We list JUMO RTD and thermocouple probes, thermowells, transmitters, controllers, recorders and water analysis instruments, and supply them to process plants, OEMs, HVAC contractors and water utilities in Oman and the GCC by type number.

JUMO company profile

Established 1948, Fulda, Germany, by Moritz Kurt Juchheim
First products Glass and contact thermometers; platinum glass sensors from 1966
Ownership Family-owned; renamed JUMO GmbH & Co. KG in 2003
Product families RTD and thermocouple probes, thermowells, temperature and pressure transmitters, controllers and thermostats, safety temperature limiters, paperless recorders, liquid analysis and flow and level instruments

Milestones

  • 1948: Moritz Kurt Juchheim founds M. K. Juchheim KG in Fulda, making glass thermometers with six employees.
  • 1966: Platinum glass temperature sensors are added.
  • 2003: The parent company is renamed JUMO GmbH & Co. KG.

JUMO products we list

Family Models Typical use
RTD and thermocouple probes 902020, 902030, 902050, 902120, 902006 2xPt100, PROCESStemp, mineral-insulated RTD, 901020 thermocouple, 901210, 902810 hygienic, 902550 surface, 902520 HVAC, MarineTemp Temperature measurement in pipes, vessels, machines, HVAC and food plants
Thermowells and inserts 909710 thermowells, 909740 measuring inserts Protecting sensors and replacing them without opening the process
Temperature transmitters dTRANS T01, T03, T04, T05, T06 SIL, T07 HART, T09, T1000 IO-Link, DELOS T switch Converting sensor signals to 4-20 mA, HART or IO-Link
Pressure and level dTRANS p20, p30, p31 hygienic, p33 Ex, p02 DELTA, MIDAS S05, MIDAS DP10, DELOS S02, MAERA S25, NESOS R20 Pressure in process, hydraulic and OEM systems; tank and well level
Controllers, limiters and recorders DICON touch, IMAGO 500, dTRON 316, iTRON, cTRON, diraTRON 104, eTRON T, safetyM STB/STW, safetyM TB/TW, LOGOSCREEN 601, mTRON T Furnace, oven and process control, over-temperature protection and recording
Liquid analysis and flow AQUIS touch S, AQUIS touch P, AQUIS 500 pH, AQUIS 500 CR, dTRANS pH 02, pH electrode, digiLine DO, ecoLine NTU, flowTRANS MAG H20, flowTRANS US W01 pH, conductivity, oxygen and turbidity in water treatment; liquid flow

Choosing a temperature sensor starts with the range and accuracy. A Pt100 RTD is accurate and stable from about -200 to 600 °C and is the usual choice in process plants. A thermocouple (type K or J, for example) covers much higher temperatures and responds faster but is less accurate. The wiring also matters: a 3-wire or 4-wire Pt100 connection cancels the resistance of the cable, while a 2-wire connection adds an error that grows with cable length. That is why a head-mounted transmitter is often fitted close to the sensor.

Where JUMO products are used

In Oman and the GCC, JUMO sensors and controllers are used in oil and gas and chemical plants, food and beverage production, plastics and metal heat treatment, HVAC and district cooling, water and wastewater treatment, swimming pools and marine applications.

Ordering JUMO products: what we need

Send the JUMO type number and the full order code from the label (for example 902020/10-...). For probes, add the sensor type (Pt100, Pt1000, type K or J), the number of wires, the insertion length and diameter, and the process connection. For controllers, add the input, outputs and supply voltage.

Facts checked against JUMO's company history, October 2026.

FAQ

Questions about the JUMO hydroTRANS S10 Indoor RH, Temperature and CO2

Answers from our engineering team on installation, compatibility and integration.

01What does the hydroTRANS S10 measure?
Relative humidity and temperature, with an optional CO2 module from 400 to 10,000 ppm.
02Which outputs does it provide?
4 to 20 mA or 0 to 10 V analog outputs, or a Modbus RTU RS485 interface, depending on version.
03Can it be used outdoors?
No, it is an indoor version for weather-protected wall mounting with an IP20 front.
04Does it calculate dew point?
Yes, it outputs calculated values including dew point, frost point and absolute humidity.
05How long does humidity accuracy take to stabilise?
The datasheet requires at least 60 hours after initial start-up.