30735489-001 (82-39-0206-06) Honeywell Pen
Overview
The 30735489-001 Honeywell Pen is a genuine Honeywell chart pen used with Honeywell recording instruments. As a consumable recording accessory, it belongs to the Honeywell range of spare parts for plant instrumentation, where it supports the ongoing operation of panel recorders and data control instruments, indicators and recorders. Listed by Honeywell parts suppliers under the Data Control System and Chart Pen/Ink categories, this accessory is identified by part number 30735489-001, with 82-39-0206-06 carried as a cross-reference in the product designation.
Chart pens are consumable items in process plants that still rely on paper chart recorders: the pen marks the trend of a measured value directly on the chart, providing a permanent record of process behaviour without any electronic storage. Keeping a spare 30735489-001 Honeywell Pen on the shelf avoids the production of unrecorded intervals when the installed pen runs dry.
Engineering & Design
Honeywell chart pens are manufactured for the pen arms of Honeywell recorders and data control instruments, where they track across the chart surface as the measured value changes. The 30735489-001 Honeywell Pen is a lightweight item, listed at approximately 0.15 lbs, and is fitted in the same manner as the original pen.
Because recording accessories are specific to the instrument family, the correct part number must be matched to the recorder model. The cross-reference 82-39-0206-06 provides an additional route for checking compatibility against Honeywell documentation and spares lists.
Key Features
- Genuine Honeywell part number 30735489-001
- Chart pen / ink accessory for Honeywell data control systems
- Used with Honeywell instruments, indicators and recorders
- Cross-referenced as 82-39-0206-06
- Lightweight: approximately 0.confirmed at quotation
Applications
- Paper chart recorders in process and utility plants
- Honeywell data control system recorders and indicators
- Replacement pen for panel-mounted Honeywell instruments
- Spare stock for maintenance departments operating Honeywell recorders, keeping a 30735489-001 Honeywell Pen ready for each change-out
Specifications
| Part number | 30735489-001 |
| Cross reference | 82-39-0206-06 |
| Type | Chart pen / ink (Data Control System > Chart Pen/Ink) |
| Manufacturer | Honeywell |
| Application | Honeywell instruments, indicators and recorders |
| Weight | Approx. 0.confirmed at quotation |
Compatibility & Integration
The 30735489-001 Honeywell Pen is intended for Honeywell recording instruments. Before ordering, check the pen arm type and chart width of the recorder against the Honeywell spares list, using the 82-39-0206-06 cross-reference as a secondary check.
Our team can confirm the application against the part number you provide. Where a plant operates several Honeywell recorders, keeping this pen in routine spares stock is the simplest way to protect continuous chart recording.
Ordering Information
To order the 30735489-001 Honeywell Pen from Seven Star LLC, quote the part number and the recorder model it is intended for. We confirm availability and delivery to your site in Oman or anywhere in the GCC, and we verify the part number against our stock before dispatch.
Why Seven Star LLC
Seven Star LLC supplies recorder accessories and instrumentation spares to industrial customers across Oman and the wider GCC region. Every Honeywell 30735489-001 pen we supply is verified against the part number before dispatch, and our team confirms the pen matches your recorder before you order.
How to Confirm the Pen Matches Your Recorder
Chart pens look similar across recorder families but are not interchangeable, and a pen that does not seat correctly on the pen arm will skip, blot or scratch the chart. The most reliable check is to compare the part number on the pen or its packaging with the recorder spares list.
- Read the recorder model and serial number from the instrument label, usually inside the door or on the chassis.
- Check the existing pen or its packaging for 30735489-001 or the cross-reference 82-39-0206-06.
- Note the number of pens and the ink colour used for each channel, so that trend colours stay consistent with the chart legend and operator practice.
- If the recorder has been modified or relabelled, send us a photograph of the pen arm and the old pen, and our team will compare them against the part data.
Fitting and Changing the Pen
Change pens with the recorder in a safe state and the chart drive accessible, following the instrument manual. Remove the used pen carefully without bending the pen arm; a bent arm causes the trace to wander from the true value and can be mistaken for an instrument fault. Seat the new pen fully, remove any protective cap, and let the recorder draw for a short while to confirm a clean continuous line. Check that the trace lines up with the chart graduations at a known value; if it does not, the problem is usually arm alignment or calibration rather than the pen.
Storage and Shelf Life
Ink pens are consumables and they do not last forever on the shelf. Store spares in their original packaging, capped, in a cool and dry store away from direct sunlight; heat dries the ink and is a real concern in unconditioned stores during Gulf summers. Rotate stock so the oldest pens are used first, and avoid ordering far more than the site uses in a reasonable period.
Troubleshooting Poor Traces
- Faint or broken line: the pen is drying out or was stored hot; replace it.
- Blots or thick line: check that the pen is seated correctly and that the chart paper is the right type and is dry.
- No trace at all: confirm that the protective cap has been removed and the pen lifter is not engaged.
Recorders are still found in utilities, water plants and older process units across Oman and the GCC, where paper charts remain part of the record-keeping routine. Seven Star LLC can supply this pen together with other recorder consumables in a single order, with lead time confirmed when you quote the part number and recorder model.
FAQ
What is the Honeywell 30735489-001?
It is a Honeywell chart pen used with Honeywell instruments, indicators and recorders, listed under the Data Control System Chart Pen/Ink category.
What does the cross-reference 82-39-0206-06 mean?
82-39-0206-06 is carried as a cross-reference part number for the same pen, providing an additional way to check compatibility against Honeywell spares documentation.
Which Honeywell instruments is this pen for?
Per the original listing, the pen is for Honeywell accessories for instruments, indicators and recorders, i.e. paper chart recording equipment.
Is the 30735489-001 a heavy item?
No. The pen weighs approximately 0.confirmed with the quotation.
Can I order the 30735489-001 pen from Seven Star?
Yes. Quote the part number and the recorder model, and we confirm availability and delivery to your site in Oman or anywhere in the GCC.
Related Products
Honeywell product families on this page
Open path infrared detection is represented by the Searchline Excel and the newer Searchline Excel Plus. Point detection includes the Sensepoint XCD in flammable and toxic versions, for example the SPXCDALMG1 hydrogen detector, the Sensepoint XRL and the XNX universal transmitter. The FS24X Plus is a triple infrared flame detector. Replacement cells such as the SR-X2V oxygen sensor and the SR-W-MP75C MICROpeL combustible sensor are also listed. Process instruments include SmartLine STG700 and STG800 gauge pressure transmitters, the STR82D remote seal transmitter and the VersaFlow Coriolis mass flow meter. Recorder consumables such as chart pens are also sourced.Where Honeywell detectors and transmitters are used
Gas and flame detectors guard wellheads, compressor stations, tank farms, loading bays, process units and utility buildings, and report to the fire and gas system. Open path units watch plant boundaries and long pipe racks. SmartLine transmitters and VersaFlow meters measure pressure and flow in refining, gas processing, chemicals and power.Ordering Honeywell gas detection parts: what we need
Send the full part number from the label, such as SPXCDALMG1 or 02104-N-XSSA, and the serial number. For gas detectors state the target gas and measuring span, housing material, cable entry thread, output (4-20 mA, relays, Modbus) and the approval required. For replacement sensors name the detector model they go into. For SmartLine transmitters send the complete model selection string.Browse Honeywell products by category: Fire & Gas Detector, Vibration, Flowmeters, Pressure Instrumentation, Temperature Instrumentation.
Reviews
There are no reviews yet.