Brand:

AUMA GS 63.3 Part-Turn Worm Gearbox, 700 Nm, F10/F12

Description

What AUMA GS 63.3 offers

For a quarter-turn valve with a 50 mm shaft and a demand of up to 700 Nm, the AUMA GS 63.3 supplies a worm gearbox weighing 12 kg with F10 and F12 valve flanges. Its single ratio of 51:1 and a factor of 17.3 mean that a handwheel or a small actuator delivering 41 Nm at the input shaft can drive a 700 Nm valve through 90 degrees in 12.75 input turns.

Where the GS 63.3 sits in the family

GS 50.3 handles 350 Nm; the GS 63.3 doubles that to 700 Nm and grows from 7.0 to 12 kg. GS 80.3 goes up to 1,400 Nm with F12 / F14, a 60 mm shaft and 16 kg. The input shaft of the GS 63.3 is 20 mm, matching the larger GS 80.3, while the input flange stays F07 (F10). So the GS 63.3 is the logical step when 350 Nm is not enough but 1,400 Nm is excessive.

GS 63.3 data

Parameter Value
Type GS 63.3, part-turn worm gearbox
Maximum valve torque 700 Nm
Modulating valve torque 250 Nm
Valve flanges F10, F12 (EN ISO 5211)
Valve shaft diameter, maximum 50 mm
Reduction ratio 51:1 (factor 17.3)
Turns of the input shaft for 90 degrees 12.75
Input shaft diameter 20 mm
Input flange for multi-turn actuator F07 (F10)
Maximum input torque 41 Nm
Strength of the end stop at the input 450 Nm
Weight 12 kg
Handwheel diameters 250 or 315 mm
Gearbox type Part-turn worm gearbox for modulating duty, bronze worm wheel
Duty Intermittent duty S4-25 percent, class C per EN 15714-2 (modulating)
Maximum input speed 215 rpm
Self-locking At standstill under normal service conditions; strong vibration may cancel it and a separate brake is needed if safe braking is required
End stops Positive for both end positions, travelling nut, sensitive adjustment
Swing angle (standard) Fixed between 10 and 100 degrees, set to 92 degrees at the factory unless ordered otherwise
Enclosure IP68 (8 m head of water); IP68-20 (20 m) as option
Ambient range Minus 40 to plus 80 degrees C; options minus 60 to plus 60 and 0 to plus 120
Lifetime (AUMA load spectrum, duty class 2) 1.2 million modulating steps for 90 degree swing
Corrosion protection and coating KS standard, KX optional; double-layer powder coat in silver-grey

Actuator and handwheel options

The usual power drive is a small multi-turn actuator on the F07 input flange, and its torque switch must be set so that the input torque limit of 41 Nm is not exceeded. For manual operation the handwheel is aluminium with ball handle, 250 or 315 mm in diameter by the datasheet table, chosen according to the output torque.

Modulating service

The gearbox is designed for S4-25 percent duty, class C under EN 15714-2, and a lifetime of 1.2 million modulating steps in the manufacturer’s duty class 2 spectrum. The modulating torque limit of 250 Nm applies to a swing of up to 90 degrees. Positive end stops, adjusted finely by the travelling nut, protect the valve with an input-side strength of 450 Nm.

Applications

Butterfly valves of DN150 to DN300, ball valves in water systems, rotary dampers and diverters are typical. In Omani pumping stations the GS 63.3 lets operators move a valve by hand at a convenient height when the electric drive is off, and the 12 kg mass is manageable for maintenance teams.

Valve attachment and swing

The valve flange is F10 or F12 with spigot rings available as an option, and the housing is plane flanged using recesses. Swing angle is fixed between 10 and 100 degrees as standard, 92 degrees at the factory, and adjustable bands to 190 degrees are available. A pointer cover gives continuous position indication; the sealed version for horizontal outdoor installation is an option.

Environment and service life of the GS 63.3

The gearbox accepts any mounting position and works from minus 40 to plus 80 degrees C, with options for minus 60 to plus 60 and 0 to plus 120 degrees C. Protection is IP68 up to 8 m head of water, or IP68-20 for 20 m. KS corrosion protection and a double-layer silver-grey powder coat are standard; KX is available. The manufacturer defines a load spectrum in which one start consists of a movement of at least 1 percent in both directions at 35 percent of the maximum valve torque.

Input shaft, options and deflection of the GS 63.3

The input shaft carries corrosion protection and is cylindrical with a parallel key per DIN 6885-1; a version with a square adapter for power tool emergency operation is optional. A GK bevel gearbox can be mounted directly on the GS to deflect the input shaft by 90 degrees. The worm wheel is made of bronze, and the housing is cast iron GJL-250 as standard or spheroidal cast iron GJS-400-15 as an option.

Bore the coupling to the shaft, mount on the valve flange and fill grease as delivered. Check seals and the pointer cover regularly. The housing is cast iron GJL-250 with spheroidal cast iron as an option.

For GS 63.3 state flange, shaft, swing angle and drive.

Documents and quotation

The manufacturer’s technical data for GS 63.3 is document Y000.289/003/en (issue 1.20) and we can send it with our reply, along with the matching output flange dimension sheet on request. For a quotation, send an RFQ with the part number GS 63.3, the quantity, the reduction ratio, the valve flange, the swing angle, the actuator you plan to mount and the shaft details. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.

Spares and Lifecycle Considerations

For critical service, many plants hold one AUMA GS 63.3 as an operational spare rather than waiting for a failure. When you plan spares, look at how many identical electric actuators units are installed, how long a replacement would take to arrive, and the cost of an unplanned stop. Store spare units in their original packaging in a dry, temperature-controlled area and record the part number and serial number in your maintenance system. We can quote single units or a small spares package and confirm the lead time for each item in writing.

Delivery to Sites in Oman and the GCC

Delivery of the AUMA GS 63.3 is arranged to suit the site, whether that is a plant in Sohar or Duqm, an oilfield location in the interior, or a project elsewhere in the GCC. Tell us the delivery point, any site access or gate-pass requirements, and the person who will receive the goods. Goods are packed to protect sensitive electric actuators equipment during road or air transport, and shipping details are shared once the order is dispatched so that your stores team can plan receipt and inspection.

Other Models in the GS Range

Seven Star LLC supplies models from the GS range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
AUMA GS 50.3 Part-Turn Worm Gearbox, 350 Nm, F05-F10Electric ActuatorsView details
AUMA GS 63.3 Part-Turn Worm Gearbox, 700 Nm, F10/F12Electric ActuatorsYou are viewing this model
Datasheets & Documents
  • PDF Datasheet AUMA GS 63.3 Part-Turn Worm Gearbox, 700 Nm, F10/F12 Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

AUMA builds electric actuators for industrial valves, gates and dampers. The company was founded in 1964 near Stuttgart by Werner Riester and Rudolf Dinse, moved its headquarters to Müllheim in south-west Germany in the early 1970s, and still trades as the owner-managed AUMA Riester GmbH & Co. KG. Its actuators run isolation and control valves in water, power, oil and gas and process plants worldwide.

Seven Star LLC is an independent supplier listing AUMA multi-turn and part-turn actuators, actuator controls, gearboxes and spare parts for buyers in Oman and the GCC. We work from the nameplate data so that a replacement matches the installed actuator, controls and gearbox.

AUMA company profile

Origin Founded in 1964 by Werner Riester (engineering) and Rudolf Dinse (sales and finance); registered as Riester KG in Esslingen. Water and wastewater plants were the first customers.
Headquarters Müllheim, Baden-Württemberg, Germany (since the early 1970s). Production in Germany, with further plants in India, the USA and China, and around 30 sales and service companies worldwide.
Ownership Privately held, owner-managed company: AUMA Riester GmbH & Co. KG
Torque and thrust range Multi-turn, part-turn and linear actuators from 1.5 Nm to 675,000 Nm with gearboxes, and linear thrust up to 217 kN, as published by AUMA
Design principle Modular: actuator, integral controls and gearbox are combined to suit the valve, so one actuator size can serve open-close, modulating, fieldbus or explosion-proof duty

Milestones

  • 1964: Werner Riester and Rudolf Dinse found AUMA near Stuttgart; the first actuator range follows, with water and sewage plants as the first customers.
  • Early 1970s: Lack of space in Nellingen leads to the move to Müllheim in south-west Germany.
  • 1974: AUMA Benelux, the first foreign subsidiary, is founded.
  • Today: About 2,800 employees worldwide, around 850 of them in Müllheim, according to AUMA.

AUMA actuator, controls and gearbox series

Series Type Typical use
SA 07.2 to SA 16.2, SA 25.1 to SA 40.1 Multi-turn actuators, open-close duty Gate and globe valves, sluice gates and penstocks; SA 07.2 to 16.2 cover roughly 10 to 1,000 Nm, the .1 sizes go far higher
SAR 07.2 to SAR 30.1 Multi-turn actuators, modulating duty Control valves that receive a continuous position setpoint and many starts per hour
SAV, SARV, SQV, SQRV Variable-speed actuators Slow approach to the seat to limit water hammer, fast travel elsewhere
SQ 05.2 to SQ 14.2, SQR Part-turn actuators Ball, butterfly and plug valves and dampers, about 50 to 2,400 Nm; SQR for modulating duty; FQM fail-safe unit for spring-return action
SAEx, SAREx, SQEx, PROFOX-MX, TIGRON Explosion-proof actuators Hazardous areas in oil, gas and chemical plants, with ATEX and IECEx certified versions
AUMA MATIC AM, AUMATIC AC, ACExC 01.2, AMExC 01.1, AC 01.2-SIL Integral actuator controls AM for simple parallel wiring; AC for positioning, diagnostics and fieldbus (PROFIBUS DP, PROFINET, Modbus, FOUNDATION Fieldbus, HART depending on version); SIL version for safety functions
GS, GHE, SA + GS combination Part-turn worm gearboxes Large butterfly and ball valves, from GS 63.3 up to GS 630.3 at 675,000 Nm
GK, GST, GHT, GP Multi-turn gearboxes (bevel, spur, worm, planetary) Offset or right-angle drives and very high multi-turn torque
LE, SVC/SVCR, PROFOX-L Linear actuators and thrust units Globe and control valves with a rising stem, up to 217 kN
PROFOX-M, PROFOX-Q Compact smart actuators Small valves where a full SA or SQ is oversized
SA-UW, SGM/SGMR, SVM/SVMR, SAN/SARN Special versions Submerged valves, seawater-exposed ship and offshore duty, nuclear plant service
SIMA2 Master station Fieldbus network management for many actuators on one plant

Where AUMA actuators are used

Water transmission and treatment is the largest use: pipeline isolation valves, pumping stations, desalination plants and sluice gates. AUMA actuators also run valves in power plant steam, feedwater and cooling systems, pipelines and tank farms, refineries and chemical plants, and on ships and offshore platforms. In the Gulf, check the ambient temperature rating, since actuators in direct sun can exceed 50 °C, and specify the enclosure protection for sand and humidity.

Ordering AUMA actuators and spare parts: what we need

For a replacement, send photos of the actuator, motor and controls nameplates: type designation, commission or order number, serial number and wiring diagram number. AUMA identifies the original build from the commission number. For a new actuator, add the valve type, required torque or thrust at the worst case, number of turns or swing angle, operating time, mounting flange to ISO 5210 or ISO 5211, stem or shaft dimensions, duty (open-close or modulating), supply voltage and frequency, control signals or fieldbus, and the hazardous-area marking required on site.

Facts checked against AUMA product information and the company history published by AUMA, October 2026.

FAQ

Questions about the AUMA GS 63.3 Part-Turn Worm Gearbox, 700 Nm, F10/F12

Answers from our engineering team on installation, compatibility and integration.

01What torque can AUMA GS 63.3 deliver?
700 Nm maximum valve torque and 250 Nm modulating valve torque.
02What ratio does GS 63.3 have?
51:1 with a conversion factor of 17.3 and 12.75 input turns per 90 degrees.
03What input torque can GS 63.3 accept?
A maximum of 41 Nm at the 20 mm input shaft of this gearbox.
04What flanges does GS 63.3 offer at the valve?
F10 and F12 per EN ISO 5211, with valve shafts up to 50 mm.
05How much does GS 63.3 weigh?
12 kg, including the unbored coupling and the grease filling.