Schneider Electric RMCA61BD Analog Current Converter

RMCA61BD analog converter and what the part number covers

RMCA61BD belongs to the Harmony Analog range from Schneider Electric and is described in its datasheet as a current-to-signal converter with an isolated 24 V DC supply. It takes AC/DC current in three ranges: 0–1.5 A, 0–5 A or 0–15 A (50/60 Hz where AC) at the input and delivers 0–20 mA or 4–20 mA into a load of up to 500 Ω, or 0–10 V into 100 kΩ or more, chosen by wiring; the output form is by cabling (terminal choice). The datasheet (dated 29 Jun 2026) shows it as discontinued on 29 Jun 2026, so availability has to be confirmed per order.

The supply is 24 V DC ± 20 %, isolated (isolated per the datasheet), and a green LED confirms power. The housing is the familiar DIN-rail enclosure with screw terminals on the top and bottom rows, designed for control cabinets rather than field mounting.

Because the converter changes the form of a signal rather than conditioning a specific sensor, it is usually selected after the receiving device is known. Seven Star LLC supplies RMCA61BD in Oman and the GCC as an independent supplier, mainly for panel retrofits and spares.

How the conversion behaves in service

The module reads the input, rescales it and drives the output stage. For RMCA61BD the datasheet states the following abnormal-state behaviour: an output pulled to about −15–0 V (voltage mode) or −30–0 mA (current mode) if the input is absent or its wire breaks. A receiving analog card should therefore be configured so that this level is read as a fault, not as a valid process value.

Output protection is stated as reverse-polarity, short-circuit and overvoltage protection on the output (overvoltage up to ±30 V). That helps when a long cable run is mis-wired during commissioning, but it does not replace proper loop wiring checks.

Use case in plain terms: reading motor, heater or feeder current directly and handing a normalised signal to a PLC analog card, a recorder or a panel meter.

Information to send with an RFQ

To quote correctly we need the following:

• Exact part number RMCA61BD and quantity.
• Input and output signal standards actually used in your loop.
• Whether you need a like-for-like replacement or are open to the current successor offered by the manufacturer.
• Delivery location in Oman or the GCC and the target date.

Installation, commissioning and maintenance

Mount the module on a 35 mm symmetrical rail or on a plate with screws. Tighten terminals within 0.6–1.1 N·m, and keep the signal wiring away from power cables; the datasheet quotes fast-transient immunity of 1 kV on the input and output and 2 kV on the supply.

During commissioning, apply a known input, measure the output with a calibrator, and also simulate a broken input wire to see how the receiving device reacts. For RMCA61BD the green LED only proves that supply is present, so it cannot show whether the signal path is healthy.

These modules have no user-serviceable parts. Keep one spare on the shelf where the loop is critical and record the wiring selection used, because a replacement has to be cabled in the same way.

Where RMCA61BD is used in Oman and the GCC

Converters like this appear in pump skids, ventilation plant, switchrooms, desalination utilities and older process panels across Oman, where a legacy instrument speaks a different signal standard from the new controller. The listed operating limit is 0–50 °C side by side or 0–60 °C with 2 cm spacing, which suits an air-conditioned electrical room but needs checking for sun-loaded outdoor cabinets in Muscat or inland sites.

Dust and humidity are managed by the enclosure around the module, not by the module itself; the datasheet lists pollution degree 2. Seven Star LLC typically supplies such converters for brownfield replacements, where matching the original wiring is more important than adding features.

Selection and ordering checklist for RMCA61BD

Before requesting a quotation, confirm these points:

• Input signal type and range, including whether it is AC, DC or bipolar.
• Required output form and whether the load stays within the stated limits (500 Ω maximum for current, 100 kΩ minimum for voltage).
• Whether a isolated supply matches your 24 V DC distribution; the datasheet gives 24 V DC ± 20 %, isolated.
• Rail space and spacing: the datasheet allows 0–50 °C side by side and 0–60 °C with 2 cm spacing.
• Whether a discontinued part is acceptable or a current replacement should be quoted instead.

RMCA61BD technical specifications

Fitting RMCA61BD into a signal chain

Compare the three Harmony Analog converters seen together: RMCA61BD accepts AC/DC current up to 15 A, RMCL55BD converts between 0–20 mA, 4–20 mA and ±10 V / 0–10 V with selectable outputs, and RMCN22BD handles 4–20 mA and 0–10 V only with a non-isolated supply. Choosing among them comes down to the input quantity, whether the output must be switchable, and whether the 24 V DC supply needs to be isolated from the signal side.

RMCA61BD is one of these three, so confirm the input and output standards against the controller or recorder you are connecting before you order.

Family comparison: three Harmony Analog converters

Documents and quotation

The datasheet for RMCA61BD is attached to this page (document dated 29 Jun 2026); it marks the product as discontinued on 29 Jun 2026. Treat it as the reference for every figure above, and expect us to confirm stock or a current replacement before we quote.

Send the part number, quantity, required delivery point and any project reference through the quotation form or by email. Seven Star LLC is an independent industrial supplier based in Muscat, serving customers across Oman and the GCC, and we reply with availability and lead time for this exact part number.