Brand:

Simtronics GD10P Infrared Point Gas Detector

Description

Overview

Simtronics GD10P is an infrared point gas detector engineered for the continuous detection of hydrocarbon gases in demanding industrial and offshore environments. Manufactured by Simtronics, part of Teledyne Gas and Flame Detection, the Simtronics GD10P has become a benchmark instrument for combustible gas monitoring on oil and gas platforms, petrochemical plants, and boiler rooms, where measurement stability and low maintenance are as important as raw sensitivity. Unlike conventional infrared detectors that rely on a filament lamp source, the GD10P uses Simtronics’ patented solid-state SimSource™ infrared emitter, giving the instrument an exceptionally long service life, immunity to vibration-induced drift, and a speed of response that is difficult to match with lamp-based designs.

Working closely with plant engineers in the region, Seven Star LLC proudly supplies the Simtronics GD10P to industrial facilities, EPC contractors, and process plants across the Sultanate of Oman and the wider GCC. Customers in Muscat, Sohar, and Salalah can source the Simtronics GD10P gas detector through Seven Star LLC with the manufacturer’s ATEX and IECEx documentation and local technical support, with lead time confirmed at quotation.

Measurement Principle

The Simtronics GD10P operates on a dual-wavelength, dual-path infrared absorption principle. Two solid-state infrared sources generate radiation that passes through narrowband optical filters selecting a measuring wavelength, at which the target hydrocarbon gas absorbs strongly, and a reference wavelength, at which absorption is negligible. Because hydrocarbon gases each possess a unique absorption spectrum, selecting the correct measuring wavelength lets the Simtronics GD10P respond only to its target gas while ignoring unrelated vapors, eliminating a common source of false alarms in catalytic or single-beam instruments. The radiation is split into an internal reference path monitored by a compensation detector and an external measuring path monitored by the main detector, and the two are continuously compared to cancel out any drift in the sources or optics themselves.

On the Simtronics GD10P, the infrared sources are solid-state, and Teledyne describes the silicon-based source as insensitive to shock and vibration, which suits environments with vibration and rapid thermal transients – conditions that are common on offshore platforms and rotating equipment skids. The four resulting signals are digitized and processed by an onboard microprocessor, which linearizes the gas response and continuously checks internal test limits against the optical and electronic paths, flagging early dirty-optics warnings long before the detector approaches an out-of-tolerance condition. The practical result for the end user is a detector with no moving parts, no consumable flame arrestor or hydrophobic mesh to clog with dust, and no requirement for field re-zeroing or re-calibration throughout its operating life.

Engineering Design of the Simtronics GD10P

Physically, the Simtronics GD10P is housed in a stainless steel (SIS2343 / ASTM 316) explosion-proof enclosure rated IP66/IP67, giving it the corrosion resistance and ingress protection required for coastal, marine, and offshore petrochemical service. The optical chamber sits behind a dual-skin weather protector that shields the internal sources and detectors from rain, dust, and salt spray without needing filters, gauzes, or sinters that would otherwise need periodic replacement, and an optional mosquito net or sunshade accessory can be fitted for facilities exposed to insects or intense solar loading. Heated optics prevent condensation from forming on the measuring path in humid coastal climates typical of the Omani coastline, keeping the detector’s response stable regardless of ambient dew point.

Electrically, the GD10P connects via a three-wire, 4–20 mA current loop (source or sink configurable) through an M20 Exe cable gland into an integral terminal compartment, removing the need for a separate junction box during installation. A HART interface layered onto the 4–20 mA signal allows technicians to configure response time and fault thresholds and to read early dirty-optics and detector-failure warnings remotely using a standard handheld HART terminal, without opening the explosion-proof enclosure. The detector requires no zero or span potentiometers, so there are no user-adjustable parts to tamper with in the field, and functional testing can be carried out from ground or eye level by applying calibration gas through the front-mounted 6 mm test nozzle.

Key Features

The Simtronics GD10P combines the reliability engineers expect from a mature offshore-proven design with features that reduce total cost of ownership over the detector’s operating life:

  • Dual-wavelength, dual-path infrared absorption measurement with independent compensation and main detectors for maximum stability.
  • Patented solid-state SimSource™ infrared emitter, eliminating the filament lamp failures common to legacy IR detectors.
  • Factory-set calibration with a specified lifetime stability of ±5% FS, meaning no field re-calibration is required over the detector’s service life.
  • Fast response, with a standard T90 of 4 seconds and an optional fast-response version rated at T90 = 1.0 second.
  • Early clean-optics and dirty-optics warnings delivered over HART, supporting condition-based rather than calendar-based maintenance.
  • Robust stainless steel (SIS2343 / ASTM 316), IP66/IP67-rated housing suitable for offshore, marine, and heavy industrial environments.
  • Global hazardous-area certification including ATEX, IECEx, CSA, and SIL 2/SIL 3 capability for safety-instrumented systems.
  • Industry-leading warranty of five years on the complete detector and fifteen years on the IR source, reducing long-term lifecycle cost.

Industrial Applications

The Simtronics GD10P is widely deployed on offshore oil and gas platforms, FPSOs, jack-up rigs, and onshore petrochemical and gas processing facilities, where continuous detection of methane, propane, butane, and other hydrocarbon vapors is essential to protect personnel and assets. The Simtronics GD10P is equally suited to boiler plant rooms, compressor stations, LPG storage and bottling facilities, biogas plants, and general industrial sites where combustible gas accumulation presents an explosion risk, and its duct-mount kit option extends its use to HVAC and ventilation air-monitoring applications.

With fast quotation turnaround and technical support, Seven Star LLC distributes the Simtronics GD10P to oil and gas operators, refineries, and industrial gas facilities throughout Oman and the GCC, including projects supported from the Sohar and Salalah economic zones where petrochemical, refining, and free-zone logistics activity concentrate much of the region’s hazardous-area gas detection demand. Facility engineers in Muscat and across the broader GCC specify the Simtronics GD10P where long-term measurement stability, minimal maintenance intervention, and full ATEX/IECEx compliance are non-negotiable requirements for safety-critical gas detection loops.

Technical Specifications

The table below summarizes the key specifications of the Simtronics GD10P infrared point gas detector as supplied by Seven Star LLC.

Parameter Specification
Model Simtronics GD10P (GD10-P00 series)
Technology Infrared absorption, dual wavelength, dual path
IR Source Solid-state SimSource™
Gases Detected Hydrocarbons (methane, propane, butane, hexane, and other HC gases; CO₂ version available)
Detection Range 0–100% LEL (0–100% volume for methane version)
Response Time (Methane) T20 = 0.7 s, T50 = 1.7 s, T90 = 4 s (optional fast version: T20 = 0.2 s, T50 = 0.4 s, T90 = 1.0 s)
Accuracy ±3% FS (0–50% reading), ±5% FS (50–100% reading)
Output Signal 4–20 mA current source/sink, HART communication
Power Supply 24 VDC (18–32 VDC), approx. 3.5 W
Housing Material Stainless steel SIS2343 (ASTM 316)
Protection Category IP66/IP67
Operating Temperature -40°C to +60°C (-40°F to +140°F)
Dimensions (L x W x H) 264 x 104 x 106 mm
Weight Approx. 2.9 kg
Certifications ATEX, IECEx, CSA, SIL 2 (SIL 3 capable software)
Warranty 5 years detector, 15 years IR source
Lifetime stability ±5% FS
Start-up time Typically 65 s
Warm-up time 30 minutes to full specification performance
Early dirty optics warning At 55% signal attenuation
Dirty optics warning At 70% signal attenuation
Max. load impedance (4-20 mA source) 500 Ω
Storage temperature -40 °C to +70 °C
Operating humidity Up to 100% RH, non-condensing
Operating pressure 1013 hPa ±20%
Cable entry M20 Ex e cable gland, 3-wire connection (0.5-1.5 mm²)

Detector Warnings and Start-Up Behaviour

According to the operating manual, the GD10P runs a continuous self-test and reports an early dirty optics warning at 55% signal attenuation and a dirty optics warning at 70% signal attenuation, so cleaning can be planned before detection is affected. Detector failure is flagged for a main function fault or blocked optics. The HART interface is used for maintenance and configuration, and the Teledyne data sheet lists analogue fault currents of 2 mA for a pre-warning, 1 mA for dirt accumulation and 0 mA for an internal fault.

After power is applied the detector typically needs about 65 seconds to start up and 30 minutes to reach full specification performance. Calibration is factory set with no field recalibration required. The manual describes a function test in which test gas is applied through a 6 mm test nozzle on the front of the weather protection while the 4-20 mA output or control system reading is observed. It also notes that pressure affects infrared measurement and that the detector is temperature compensated over its operating range.

Versions, Response Options and Accessories

Teledyne lists standard gas versions for methane and propane with ranges of 0-100% LEL or 0-100% volume, and 0-100% LEL for other flammable gases. The standard response time, measured on methane in natural diffusion and without weather protection, is T20 = 0.7 s, T50 = 1.7 s and T90 = 4.0 s, with an optional fast version at 0.2 s, 0.4 s and 1.0 s. Output is a 4-20 mA current source, with current sink as an option.

The data sheet lists a front cover that must be selected, with weather protection supplied as standard and a sample flow housing for sampling systems and bump tests. Accessories include a mosquito net for extra insect protection, a sun shade for extreme solar radiation or snow deposit, and a duct mount kit for duct monitoring. Approvals listed include ATEX, IECEx, INMETRO and CSA, with functional safety certified to SIL 2 SC3 high demand, and marine approvals MED and ABS.

Request a Quote for Simtronics GD10P Infrared Point Gas Detector

Facility engineers and procurement teams across Oman and the GCC can request a formal RFQ for the Simtronics GD10P infrared point gas detector directly from Seven Star LLC, with lead time confirmed at quotation and full technical datasheets provided on request. With engineering support in Muscat, Seven Star LLC’s instrumentation division supports specification and sizing of Simtronics GD10P gas detection loops from initial enquiry onward, with local technical support.

Related Products

Datasheets & Documents
  • PDF Instruction Manual Simtronics GD10P Infrared Point Gas Detector Manual Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Simtronics is a fire and gas detection brand with operations in Oslo, Norway, and Aubagne, France. It makes infrared gas detectors, flame detectors and fire and gas control systems for oil and gas, marine and industrial sites. United Technologies' UTC Fire & Security took control of Simtronics in 2011, and in 2013 it was sold to Industrial Safety Technologies. Teledyne has owned Simtronics since 2019, when it bought 3M’s gas and flame detection business.
Seven Star LLC sources and supplies Simtronics gas detectors and flame detectors for fire and gas systems in Oman and the GCC. Recent documents for these products may also carry the Teledyne Gas and Flame Detection name.

Simtronics company profile
OperationsOslo, Norway and Aubagne, France2011Acquired by UTC Fire & Security2013Sold to Industrial Safety TechnologiesApplicationsOffshore, onshore oil and gas, marineProduct familiesGD10P infrared point gas detectors, DM-TV6 flame detectors, MultiFlame detectors, fire and gas control panels

Milestones
2011: UTC Fire & Security acquires Simtronics.2013: Simtronics joins Industrial Safety Technologies.

Simtronics detectors listed

The GD10P is an infrared point gas detector for hydrocarbon gas, built around a solid-state infrared source; a separate version measures carbon dioxide. It is listed here both as a series and under one full order code, GD10-P00-17DG-0XH-00, which shows how much of the configuration sits in the code. The third item is the DM-TV6-T, a flame detector that works on three infrared wavelengths. Newer documents also use the designation DF-TV7 for this detector family.

Simtronics products we list
FamilyExamplesFire & Gas DetectorsDM-TV6-T Flame Detector, GD10-P00-17DG-0XH-00 Infrared Gas Detect…, GD10P Infrared Point Gas Detector

Ordering Simtronics GD10 and flame detectors: what we need

Send the complete order code from the nameplate; for a GD10P that is the long string with all its groups. The groups in the code fix the configuration of the detector, and two detectors with different codes are not automatically interchangeable. Add the serial number, the target gas, the hazardous area certification your site requires (ATEX or IECEx, for example) and the cable entry thread. For a flame detector, give the exact type including the last letter, plus the mounting accessories needed.

Facts checked against UTC and Industrial Safety Technologies acquisition releases, October 2026.

Browse Simtronics products by category: Fire & Gas Detector.

FAQ

Questions about the Simtronics GD10P Infrared Point Gas Detector

Answers from our engineering team on installation, compatibility and integration.

01What gases does the Simtronics GD10P detect?
The Simtronics GD10P is an infrared point gas detector primarily configured for hydrocarbon gases such as methane, propane, and butane, with detection ranges typically covering 0-100% LEL. Alternative gas-specific versions, including a CO2 variant, are also available from the GD10 series.
02Does the GD10P require field calibration?
No. The GD10P uses a factory-set dual wavelength, dual path optical design with a specified lifetime stability of +/-5% FS, so no field re-calibration is required; a periodic function test with test gas is still advisable.
03What certifications and approvals does the GD10P carry?
The Simtronics GD10P holds ATEX and IECEx certification for hazardous areas, CSA approval for North America, and is SIL 2 certified with SIL 3 capable software, making it suitable for use in safety-instrumented gas detection systems across offshore and onshore facilities.
04Can the GD10P be retrofitted into an existing catalytic detection system?
The GD10P provides a 4-20 mA current-source output (current sink optional) with HART for maintenance, so it connects to a standard 4-20 mA gas detection input. Whether it can replace a catalytic detector depends on the existing control module and cabling, so please confirm the loop details with us first.
05Is Seven Star LLC an experienced supply partner for Simtronics products?
Yes. Seven Star LLC is an experienced supplier of Simtronics in Oman and the GCC, supplying genuine factory-calibrated GD10P gas detectors with technical documentation, and local after-sales support.