Schneider Electric A9V22325 Vigi iC60 3P 25 A 100 mA

A9V22325: Vigi iC60 3P 25 A 100 mA add-on block

The A9V22325 is a Schneider Electric Acti9 Vigi iC60 add-on residual current device in a three-pole version, rated 25 A with 100 mA sensitivity and Type A detection. It is not a stand-alone breaker: it is clipped to the side of a compatible iC60 miniature circuit-breaker and connected by screws, which adds earth-leakage protection to the overload and short-circuit protection that the breaker already provides. Seven Star LLC supplies the A9V22325 in Oman and the GCC as an independent supplier based in Muscat.

Decoding the product from the datasheet: A9V22325 has a 230–415 V AC rated operational voltage, so the block can sit on a single-phase 230 V circuit or on a three-phase system up to 415 V, it occupies 6 modules of 9 mm and weighs 0.21 kg. Its tripping is voltage independent, meaning the residual current function does not depend on the mains voltage being present to operate.

What 100 mA and Type A mean for the A9V22325

The A9V22325 offers a 100 mA threshold, a medium sensitivity that is typically selected to protect against earth-fault currents in a feeder or to leave room for time discrimination with finer downstream devices, not as the main protection for personal contact. The tripping delay is listed as instantaneous, so there is no built-in time delay for selectivity at this reference.

Type A responds to sinusoidal alternating residual current and to pulsating DC residual current, which makes it a better match for single-phase rectifier loads and electronic equipment that can inject such components into an earth fault. Selecting the sensitivity and the type is a design decision, not a catalogue preference: use the earthing system, the load type and the applicable wiring rules to decide, and avoid putting several loads with natural leakage behind one very sensitive block.

Where the A9V22325 fits in Oman and the GCC

Earth-leakage add-on blocks of this kind are used in commercial buildings, camps, workshops, pump houses, desalination plant auxiliaries, utility substations, and small distribution boards in oil and gas facilities. A 100 mA three-pole unit such as the A9V22325 is normally installed on feeders, with finer devices downstream. Humid coastal air, dust and high summer temperatures put stress on terminals and on the test mechanism, so periodic inspection is a good habit.

Technical specifications of the A9V22325

Compatible iC60 breakers for the A9V22325

The datasheet lists the range compatibility as Acti9 iC60 miniature circuit-breaker and Acti9 Reflex iC60 integrated control circuit breaker. The product compatibility entries for the A9V22325 are: IC60a/N/H/L/P single terminal miniature circuit-breaker ≤ 25 A; Disbo iC60N/H miniature circuit-breaker ≤ 25 A; IC60L MA miniature circuit-breaker ≤ 16 A; Reflex iC60 integrated control circuit breaker ≤ 25 A. The upper current limit in each line is the point to watch: the add-on block rated 25 A is intended to pair with breakers at or below that class, and some breaker versions are restricted to lower currents than the others.

The Reflex iC60 integrated control circuit breaker is included in the compatibility list, so the block can also be used with that control-breaker version. Because the block has 3 poles, the breaker normally has to match that pole count; confirm the pairing against the compatibility table before ordering the breaker and block as a set.

Other Vigi iC60 blocks and how they differ from the A9V22325

The other 3-pole blocks in our lane are: A9V41325 (3P 25 A 30 mA AC), A9V41363 (3P 63 A 30 mA AC). Across the entire set, the key differences are pole count, current class (25 A, 40 A or 63 A), sensitivity (10, 30, 100 or 300 mA), type (AC or A) and the voltage window. The A9V22325 is the one with 3 poles, 25 A, 100 mA, Type A and 230-415 V AC 50/60 Hz V AC.

For reference, the wider list we are quoting is: A9V01225 (2P 25 A 30 mA), A9V10225 (2P 25 A 10 mA), A9V12225 (2P 25 A 100 mA), A9V12263 (2P 63 A 100 mA), A9V12463 (4P 63 A 100 mA), A9V41225 (2P 25 A 30 mA), A9V41263 (2P 63 A 30 mA), A9V41325 (3P 25 A 30 mA), A9V41363 (3P 63 A 30 mA), A9V41425 (4P 25 A 30 mA), A9V41440 (4P 40 A 30 mA), A9V41463 (4P 63 A 30 mA), A9V44240 (2P 40 A 300 mA). The width and the weight also change with pole count and current, which affects how much space the combination takes in a board.

Installation and testing of the A9V22325

Connect the this unit to the bottom of the matching breaker with the supplied screw connection, then fix the assembly on DIN rail. Terminals at the bottom are tunnel type: 1–25 mm² rigid without cable end; 1–16 mm² flexible without cable end; 1–16 mm² flexible with cable end. Strip the conductor to 14 mm and tighten to 2 N.m; the comb busbar is compatible at the bottom.

After energising, use the front test button to confirm tripping, and check the trip indicator shows the fault state. Record the test in the maintenance log and repeat it at regular intervals. Keep in mind the temperature window of -25–60 °C for operation; in hot enclosures at Gulf sites, mount the block away from other heat sources and consider derating or ventilating the board. The unit is IP20 on its own and IP40 when fitted in a modular enclosure.

Information to send with an RFQ for the A9V22325

For a fast quotation on the this unit, send the part number, quantity, the type and rating of the miniature circuit-breaker it will be fitted to, the system voltage and earthing arrangement, the residual current sensitivity required by your design, and the delivery address in Oman or the GCC. If you are replacing an existing assembly, a photo of the label helps us match the pole count and current class.

Documents and quotation

A datasheet for the this unit is attached on this page. The version we reviewed is dated 8 Nov 2026.

Send the part number and your project details through the RFQ form; Seven Star LLC will confirm availability and lead time in Oman and the GCC.