Schneider Electric RPM22P7 RPM Relay 230 V AC

RPM22P7 RPM power plug-in relay and its part number

RPM22P7 is an RPM power plug-in relay from the Schneider Electric Harmony Electromechanical Relays range. Its datasheet lists 2 C/O contacts, an AC coil rated 230 V AC 50/60 Hz, and a status LED fitted. Mounting is plug-in, with flat faston-type pins.

Reading the code from the datasheets of this family: RPM22 = RPM series power relay with two changeover contacts; the suffix P7 stands for the coil, here 230 V AC 50/60 Hz. This reading follows how the sibling datasheets line up and is not an ordering table, so verify the full code against the manufacturer catalogue when it matters.

Seven Star LLC supplies RPM22P7 in Oman and the GCC as an independent supplier in Muscat. The datasheet we hold is dated 8 Nov 2026.

Installation, commissioning and maintenance

Start by checking the socket wiring against the relay pin diagram, then plug the relay in and energise. RPM22P7 is described with IP rating IP40 conforming to IEC 60529, and its ambient limits are -40–55 °C for operation; keep it clear of heat sources such as power supplies and braking resistors in the same enclosure.

During commissioning, energise the coil at its nominal voltage, check contact transfer with a meter, and verify that the supply stays inside the voltage limits. In service, inspect for discoloured pins, replace relays that show contact wear, and keep a spare on the shelf for critical interlocks.

Sockets and related parts for RPM22P7

The matching sockets are RPZF2 for the two-pole RPM relay and RPZF4 for the four-pole one; the datasheet of the socket confirms RPM with 2 C/O contact for RPZF2.

The same series also includes the following parts, which share the basic body of RPM22P7 but differ as shown:

• Against RPM22BD: coil 230 V AC 50/60 Hz against 24 V DC on RPM22BD; drop-out ≥ 0.15 Uc AC against ≥ 0.1 Uc DC on RPM22BD.

Because the differences are in the coil or contact details, the complete part number must be confirmed before ordering.

Family comparison and RFQ details

For a quotation on RPM22P7 please send the exact part number, quantity, coil voltage, delivery location in Oman or the GCC and any project reference. If your drawing lists a different coil voltage, say so and we will check the matching variant.

Typical use of RPM22P7 in Oman and the GCC

In Oman and the GCC, relays like this commonly sit in motor control centres, pump and compressor skids, fire-and-gas panels, HVAC plant rooms and utility switchrooms, where they isolate PLC outputs from heavier circuits. Heat inside sun-exposed cabinets and salt-laden coastal air are the main points to design for; the datasheet lists pollution degree 3 and IP rating IP40 conforming to IEC 60529.

RPM22P7 suits panels that need 2 C/O switching with a status LED fitted and a lockable test button, and where the supply is 230 V AC 50/60 Hz.

Coil circuit and supply window of RPM22P7

The coil of RPM22P7 is rated 230 V AC 50/60 Hz with voltage limits of 184–253 V AC. The datasheet gives an average coil resistance of 16270 Ohm at 20 °C ± 15 % and average consumption of 1.1 at 60 Hz VA. The relay releases when the control voltage falls to ≥ 0.15 Uc AC, which is the figure to compare against any sagging control supply or leakage from a PLC output.

Operating time is 20 ms at nominal voltage and release time 20 ms at nominal voltage. An LED shows coil energisation, and the lockable test button allows manual operation checks.

A 230 V AC coil is a direct mains-voltage control supply, which suits GCC single-phase distribution; use fused, segregated wiring and watch for residual voltage on long cable runs.

RPM22P7 technical specifications

Contact ratings and switching limits

Contact data for RPM22P7: maximum switching capacity 3750 VA; 420 W, minimum switching capacity 170 mW at 10 mA, 17 V; contact material AgNi.

Rated operational current entries:

• 15 A at 277 V (AC) conforming to UL
• 15 A at 28 V (DC) conforming to UL
• 15 A at 250 V (AC) NO conforming to IEC
• 15 A at 28 V (DC) NO conforming to IEC
• 7.5 A at 250 V (AC) NC conforming to IEC
• 7.5 A at 28 V (DC) NC conforming to IEC

Durability: 100000 cycles for resistive load. Derate for inductive or DC loads and follow the curves in the datasheet.

Selection and ordering checklist for RPM22P7

Before ordering this unit confirm:

• Control voltage: 230 V AC 50/60 Hz (184–253 V AC); AC and DC versions are not interchangeable.
• Contact load: check the load against 3750 VA; 420 W and the current table above.
• Indicator needs: this version is with a status LED.
• Socket type and terminal style matching the relay pins.
• Quantity and whether a spare relay should be held for the plant.

Documents and quotation

The datasheet for this unit is attached to this page (document dated 8 Nov 2026). Please treat it as the reference for every figure above, and tell us if your project specification asks for anything the datasheet does not state.

Send the part number, quantity, required delivery point and any project reference through the quotation form or by email. Seven Star LLC is an independent industrial supplier based in Muscat, serving customers across Oman and the GCC, and we reply with availability and lead time for this exact part number.