Reelcraft TW86075 OLPT 75 ft. Twin Line Welding Hose Reel

Oxygen and fuel gas on one retractable reel

The Reelcraft TW86075 OLPT is a Series TW80000 twin-line spring-retractable welding reel, built to carry oxygen and fuel gas together. A 3/8 in. x 75 ft twin welding hose in T-grade is included, so the reel supplies a torch with both gases from one wall or post mount.

Reelcraft says the Series TW design aims to improve safety and productivity in the work area. The baked-on red powder coat resists corrosion, and the frame, spool and drum are heavy-gauge steel. The double-sealed swivel uses specially molded O-rings, and the two swivel inlets are permanently identified with machined grooves on the gas side so the lines cannot be installed the wrong way round.

Page features

• Seals and hoses are T-grade, for gases including MAPP, propane, natural and fuel gases
• Robotically welded steel base; individually powder-coated components
• Included hose: 601040-75 3/8 in. x 75 ft twin welding T-grade
• Ships LTL only; made in the USA

Technical specification

Reel data

Materials

TW80000 codes in the manual

TW denotes twin-line welding, 8 the 80000 series, then 6075 the 3/8 in. size and 75 ft length; OLPT is low-pressure T-grade. The same manual lists TW84000, TW84100, TW86000 and TW86050 variants; the reels without hose (TW84000 OLPT and TW86000 OLPT) are the ones the manual describes as UL listed (#70H2).

The product page quotes a 10 day estimated lead time and notes that Series 80000 reels only ship LTL, so plan for pallet or freight delivery rather than courier. At 99 lb with hose, it is the heaviest of the welding reels listed here.

Gas safety and installation from instructions 834-696D

The manual warns against closing the fuel gas at the regulator first, as flashback may damage the hose; close at the torch, then at the regulator or supply, and bleed remaining gas after shutdown. It also asks for adequate ventilation, particularly in confined spaces, and follows NEC, OSHA and local code for installation.

• Install no higher than 16 ft unless specified at order.
• Use a wrench on the fittings on the shaft when tightening the hose connector.
• Rewind the hose and bleed pressure before replacing the hoses or swivel; user servicing is limited to those.
• Identify the oxygen and fuel gas inlets using the grooves on the gas side so lines are not crossed.

Cutting and brazing stations

Twin reels bring oxy-fuel to bench stations, pipe racks and maintenance bays, keeping 75 ft of hose off the ground so it is not run over or burned. Gulf yards benefit from the heavy powder coat but hose and cylinders should still be shaded from sun. Follow your site hot-work permit rules for gas cylinders and flashback protection. The twin hose uses 3/8 in. size at 200 psi, which is within normal oxy-fuel regulator pressures, but check regulator outlet settings and the T-grade hose rating for the gas you use. The reel is heavy at 99 lb, so use rated anchors on masonry or steel.

Selection and installation notes

A twin-line welding reel carries oxygen and fuel gas together, so use only hose and fittings approved for each gas, fit flashback arrestors and check valves at the torch and at the regulators, keep the reel away from oil and grease and from ignition sources, test the connections with a leak solution and follow the site hot-work rules. Replace the hose if it is cracked, burnt or worn.

Information needed for a quotation

Send the full model code, the quantity, the delivery location in Oman or the GCC, the intended use and any accessories needed, so that the complete package can be quoted together.

Documents and supply information

The manufacturer data sheet is attached to this page and should be read together with the project specification and the site risk assessment before a purchase is confirmed. Ratings, standards and dimensions are quoted as printed on that sheet. Lead time, stock position and certificates available with the shipment are confirmed in the quotation, and we supply to Oman and the wider GCC region for industrial, utility and building services projects.

Related items

The page lists 601040-75 hose, S600521 bumper stop, S601031-2, -4 and -6 one-quarter-inch twin welding inlet hoses, a 600801 340 degree pivot base and the 600980 wall swing bracket. Flashback arrestors and regulators are not listed and must be sourced separately.

Reelcraft also publishes tech bulletins on hose replacement and required wraps (TB0020) and a twin welding bulletin (TB0024) linked from the product page, which help when re-tensioning the spring after changing the hose.

Related Reelcraft products: Reelcraft SWHD76100 OLPT 100 ft. Single Line Welding Reel, Reelcraft RS7850 OLP 1/2 in. x 50 ft. REELSAFE Hose Reel, Reelcraft 7850 OMP 1/2 in. x 50 ft. Oil Hose Reel with Hose, Reelcraft 5600 OMP 3/8 in. x 30 ft. Oil Hose Reel, 3000 psi, Reelcraft GCCA33112 L 3/4 in. x 100 ft. Hand Crank Hose Reel and Reelcraft E9300 OMPBW 3/4 in. x 50 ft. Vehicle-Mount Oil Reel.

Documents and quotation

The linked PDF is Reelcraft form 834-696D, the Series TW80000 instruction manual. The photograph shows a TW80000 family reel from the maker page. Send your gas types, hose length and mounting position for a quote; approvals, freight and availability need confirmation with us before ordering. Seven Star LLC is an independent supplier in Muscat. More products in this range are listed under Welding Accessories & Safety.