Simtronics GD10-P00-17DG-0XH-00 Infrared Gas Detector (GD10P Series)

Overview

The Simtronics GD10-P00-17DG-0XH-00 Infrared Gas Detector is a GD10P Series point detector from Teledyne Simtronics, designed for combustible gas detection in industrial plants. The GD10P Series is an infrared gas detector family, and this configuration is set up for CH4 methane detection over the 0-100% LEL range, with ATEX certification for use in hazardous areas and HART communication for integration with plant control systems. For oil, gas and petrochemical facilities in Oman and the GCC, the Simtronics GD10-P00-17DG-0XH-00 is a genuine replacement detector for installed Simtronics gas detection systems.

Engineering Design

The GD10P detector uses infrared measurement technology to monitor the presence of combustible gas in the atmosphere. The infrared source and detector arrangement measures the absorption of infrared energy by the target gas, and because the measurement principle is physical rather than catalytic, the sensor is not consumed by the gas it detects. This configuration is specified for CH4 methane monitoring over the full 0-100% LEL range, with the detector output available through the HART protocol, which allows the device to be interrogated, calibrated and diagnosed digitally over the same two-wire loop used for the measurement signal.

Compatibility & Integration

The detector is part of the Simtronics GD10P Series, so it integrates with existing Simtronics gas detection systems and their associated monitoring infrastructure. The HART output allows the detector to be connected to HART-capable control systems, marshalling panels and handheld communicators, which simplifies commissioning and routine maintenance in plants that already use HART instruments.

With ATEX certification, the Simtronics GD10-P00-17DG-0XH-00 is suited to hazardous-area installations where combustible gas may be present, and the 0-100% LEL range gives the control room a direct reading of how close the atmosphere is to the lower explosive limit. Plants typically mount the detector in the gas release risk areas and connect the output to the fire and gas system or the process control system.

Key Features

• GD10P Series infrared gas detector from Teledyne Simtronics
• CH4 methane detection over 0-100% LEL
• ATEX certified for use in hazardous areas
• HART communication for digital integration with plant systems
• Infrared measurement principle with no consumable sensing element
• Full configuration: Simtronics GD10-P00-17DG-0XH-00

Industrial Applications

• Combustible gas monitoring in oil, gas and petrochemical facilities
• Gas compressor stations, processing units and storage areas
• Hazardous-area installations requiring ATEX-certified detectors
• Plants across Oman and the GCC operating Simtronics gas detection systems

Technical Specifications

Why Seven Star LLC

Seven Star LLC supplies gas detection equipment and spares to industrial customers across Oman and the wider GCC region. Every GD10-P00-17DG-0XH-00 we supply is checked against the configuration code before dispatch, and our team confirms the detector matches your installed Simtronics system and hazardous-area classification before you order.

Reading the GD10P Configuration Code

Simtronics GD10P detectors are identified by a full configuration code, and every position in the code matters. It defines items such as the gas calibration, the measuring range, the output and communication option, and the certification. For a like-for-like replacement, copy the complete code from the label of the installed detector rather than ordering by series name alone. Also check:

• That the target gas and range on the label, CH4 methane at 0-100% LEL for this unit, match the fire and gas cause and effect documentation.
• The certification marking and cable entry arrangement required at the installation point.
• The accessories used on site, such as the weather protection, calibration adaptor and mounting bracket.

Installation and Commissioning

Methane is lighter than air, so point detectors for methane are normally placed above potential leak sources such as compressor seals, flanges and valve stations. Final positions should follow the site gas detection layout, taking air movement and ventilation into account. After wiring and power-up, allow the detector to warm up and stabilise. Then confirm the zero reading in clean air and verify the response with certified methane test gas applied through the correct calibration accessory. Use the HART connection to check the device configuration and tag. Finish by confirming the analog signal and alarm levels at the fire and gas system.

Maintenance and Troubleshooting

The infrared measurement principle has no consumable catalytic element, so routine work focuses on keeping the optical path clean and proving the response. Recommended practice includes:

• Periodic gas tests at the interval set by the site procedure, with the results recorded
• Inspection and cleaning of the optics and weather protection, particularly after sandstorms or heavy dust
• Using HART diagnostics to read fault and status information before removing a detector from service

A persistent optics or beam-block fault usually indicates dirt, condensation or an obstruction in the measuring path.

Applications in Oman and the GCC

Gas processing plants, compressor stations, wellhead facilities and terminals across Oman and the GCC use Simtronics detectors in their fire and gas systems. The Simtronics GD10-P00-17DG-0XH-00 lets operators keep installed systems on the same detector family, which simplifies spares and training.

Supply from Seven Star LLC

Seven Star LLC supplies Simtronics gas detectors and accessories for replacements and system extensions. Send the full configuration code from the installed unit, and our team will confirm the match.

Ordering Information

To order the Simtronics GD10-P00-17DG-0XH-00 from Seven Star LLC, quote the full configuration code together with the quantity required. Our team confirms availability, certification documents and delivery to your site in Oman or anywhere in the GCC.

FAQ

Related Products

• Teledyne C70043A PCB Assembly, Paramagnetic Preamp for MDL 3000 Series
• AMETEK 300-8707 Copper Hollow Cathode Lamp (Cu HCL)
• CS Instruments FA 510/515 – Dew Point Sensor for Compressed Air & Gases
• Hach LBOD0101Intellical Laboratory Luminescent Optical Dissolved oxygen
• Siemens Maxum II FID 302A Detector Assembly 2021651-002
• Air Products SPAN GAS -HYDROGEN(2%) BEL AIR,34 L