Schneider Electric SRVS1KRIRK Easy UPS 1 kVA Rack

SRVS1KRIRK: 1 kVA 2U rackmount Easy UPS 1Ph On-Line

The SRVS1KRIRK is a Schneider Electric Easy UPS 1Ph On-Line unit rated 1000 VA / 800 W with a sine-wave double-conversion output. It is built as a 2U rackmount chassis with a rail kit. Seven Star LLC supplies the SRVS1KRIRK in Oman and the GCC as an independent supplier based in Muscat.

The datasheet carries a lifecycle notice: the reference is marked discontinued, with a stated discontinuation date of 31 Oct 2026 and end of service on 30 Aug 2029. Check current availability and ask about replacement options when you enquire. The reading of the reference below is our interpretation of the product title, not a published ordering table: SRVS1KRIRK is described as a standard runtime model, with a 19-inch rail kit included, and a socket-outlet output.

Typical uses of the SRVS1KRIRK in Oman and the GCC

A 1 kVA on-line unit like this unit suits plant instrumentation and PLC panels, building-management and access-control systems and point-of-sale and back-office equipment, where mains dips and short outages cause more damage than a long blackout would. Gulf sites also deal with high ambient temperatures, dust and unstable feeders from generators or weak grids, so the clean sine output and the input window are valuable, but room cooling and a dust-free enclosure matter just as much as the unit rating. Where autonomy is only needed to ride through brief outages or to shut systems down cleanly, the built-in battery arrangement is usually enough.

How the SRVS1KRIRK compares with sibling references

The nearest relatives in the same range, taken from their own datasheets, are listed here. They share the on-line topology, LCD console and card slot but differ in power, chassis and battery arrangement.

Technical specifications of the SRVS1KRIRK

Selection checklist for the SRVS1KRIRK

• Load: connected load must stay within 800 W as well as 1000 VA; the watt figure is the limiting one when the load has a power factor below the rating.
• Connections: confirm the inlet type and that the sockets match your equipment plugs.
• Form: rack with 2U space and suitable depth.
• Runtime: standard battery only; check the stated runtime against your needs.
• Lifecycle: the datasheet shows the reference as discontinued, so confirm stock and a replacement before committing a project.

Installation, commissioning and maintenance of the SRVS1KRIRK

Before first start, check that the input supply, frequency and earthing agree with the datasheet, and set the nominal output voltage to match the equipment. Operate within 0–40 °C ambient, relative humidity up to 95 % without condensation and altitudes up to 3000 m; the enclosure is IP20, so the room must be clean and indoor. Use a supply cord and outlet appropriate for the rated current.

After commissioning, test the transfer to battery with a real load, record the runtime, and log it for later comparison. Keep the intelligent-card slot and the USB or serial port in mind if you want remote alarms. Maintenance should cover battery condition, fan and vent cleanliness, firmware or card settings and a periodic check of the bypass operation.

Power path and output behaviour

In on-line operation the load is always fed from the inverter, so the output is isolated from mains disturbances and the datasheet lists a sine waveform at 50/60 Hz ± 3 Hz synchronised to mains. The input accepts 230 V AC single phase with 220 V and 240 V also listed, and an auto-sensing frequency range of 40–70 Hz; the output is configurable for 220, 230 or 240 V nominal. Crest factor is 3:1 and an internal bypass is provided with both automatic and manual operation. This unit lists an efficiency of 88 % (full load) at full load.

The input window is stated as 110–285 V half load and 160–280 V full load, which describes the mains range over which the unit can carry load without going to battery. In practice that is a useful margin on weak or fluctuating supplies, but the figures belong to the datasheet and the unit’s own protection limits apply.

Size, weight and mounting of the SRVS1KRIRK

The chassis measures 86 × 438 × 312 mm (H × W × D) and weighs 11 kg. It mounts horizontally in a 19-inch rack and occupies 2U of rack height; the datasheet lists mounting preference as lower in the rack, which matters because of the weight of the battery section. A rail kit is included. Check the rack depth against the 312 mm chassis and the connector space behind it.

Acoustic level is 50 dBA and heat dissipation is not listed. Heat dissipation is not given in this datasheet, so estimate losses from the efficiency figure and the real load.

Information to send with an RFQ for the SRVS1KRIRK

• Exact reference SRVS1KRIRK and the quantity needed.
• Connected load in W and VA, and the required runtime.
• Available supply voltage and frequency, and the earthing arrangement.
• Whether matching battery packs, rail kits or a network card are needed in the same order.
• Delivery location and project timeline, plus any replacement requirement given the lifecycle notice.

Documents and quotation

The manufacturer datasheet for the SRVS1KRIRK is attached on this page. It carries the full specification summarised above and the lifecycle notice; check its revision date against your project.

Send us the reference SRVS1KRIRK, quantity and delivery location and Seven Star LLC will reply to your request. We supply as an independent supplier based in Muscat.