- Automation & ControlView all 2,741 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Servo Drives
- Pneumatic Cylinders
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Pepperl+Fuchs
Pepperl+Fuchs KFD2-SOT2-Ex1.LB.IO Switch Amplifier, 1-Ch Transistor
Description
Pepperl+Fuchs KFD2-SOT2-Ex1.LB.IO overview
The Pepperl+Fuchs KFD2-SOT2-Ex1.LB.IO is a one-channel isolated switch amplifier from Pepperl+Fuchs that moves a NAMUR sensor or dry contact signal from a hazardous area to a safe area. The single input controls two passive transistor outputs. Switches on the front reverse the mode of operation and switch the line fault detection off, and a further switch decides whether the second output works as a second signal output or as a fault indication output.
Faults are shown by LEDs according to NAMUR NE 44, and a separate collective error message is available when the module is used on the Power Rail. The datasheet released on 10 January 2022 lists SIL 2, a switching frequency up to 5 kHz and a switching current up to 100 mA per output. In practice, the second output as a fault signal lets the control system distinguish a real switching event from a wiring fault on the same loop.
Key features of the Pepperl+Fuchs KFD2-SOT2-Ex1.LB.IO
- One input channel controlling two passive transistor outputs
- Second output selectable as signal output or fault indication output
- NAMUR input according to EN 60947-5-6 with line fault detection that can be switched off
- Switching frequency up to 5 kHz and output current up to 100 mA, short-circuit protected
- SIL 2 according to IEC/EN 61508
- LED fault display according to NAMUR NE 44 and Power Rail collective error message
- Supply 20 to 30 V DC through Power Rail or terminals 14 and 15
- Housing type B2, 20 mm wide, IP20, minus 20 to 60 degrees C
KFD2-SOT2-Ex1.LB.IO technical specifications
The values below are taken from the manufacturer datasheet of the KFD2-SOT2-Ex1.LB.IO, release date 2022-01-10. Always confirm the current datasheet and the certificates before final engineering.
| Parameter | Value |
|---|---|
| Model | KFD2-SOT2-Ex1.LB.IO, Switch Amplifier, 1-channel isolated barrier |
| Signal type | Digital input |
| Safety Integrity Level | SIL 2 |
| Rated supply voltage | 20 to 30 V DC, ripple up to 10 percent (Power Rail or terminals 14+, 15-) |
| Rated current | Up to 50 mA |
| Input | NAMUR according to EN 60947-5-6; terminals 1+, 2+, 3- |
| Open circuit voltage / short-circuit current | Approx. 8 V DC / approx. 8 mA |
| Switching point / hysteresis | 1.2 to 2.1 mA / approx. 0.2 mA |
| Line fault detection | Breakage 0.1 mA or less; short-circuit above 6 mA |
| Output | Output I: passive electronic output, terminals 7, 8; output II: signal or error message, passive transistor, terminals 10, 11 |
| Switching voltage / current | Up to 30 V / up to 100 mA, short-circuit protected |
| Signal level | 1-signal: switching voltage minus 2.5 V at 10 mA, or minus 3 V at 100 mA; 0-signal: off-state current up to 10 microamperes |
| Switching frequency | Up to 5 kHz |
| Isolation | Input to output and to supply: reinforced insulation, 300 V rms; output to supply and output to output: basic insulation, 50 V |
| Hazardous-area marking | (1)G [Ex ia] IIC; certificate PTB 00 ATEX 2035; also (M1) [Ex ia] I, DMT 01 ATEX E 133 |
| Input Ex ia values | Uo 10.5 V, Io 13 mA, Po 34 mW (linear characteristic) |
| Zone 2 certificate | TUV 99 ATEX 1499 X, marking Ex nA II T4 |
| IECEx | IECEx PTB 05.0011 |
| Ambient temperature | Minus 20 to 60 degrees C |
| Dimensions / mass | 20 x 119 x 115 mm (W x H x D), housing type B2 / approx. 150 g |
| Degree of protection / mounting | IP20, screw terminals / 35 mm DIN rail |
Both outputs are passive, so each needs an external supply and load. Decide at engineering stage whether output II will be a signal duplicate or a fault output and document the switch position.
Typical applications in oil and gas, utilities, water and manufacturing
Position and process switching in hazardous areas relies on NAMUR proximity sensors and dry contacts, from valve limit switches on ESD valves at wellheads to level switches on storage tanks and flow switches on cooling water lines. The KFD2-SOT2-Ex1.LB.IO passes these signals out of the hazardous area to relays, PLC inputs or annunciators, and its line fault detection tells operators when a cable is open or shorted instead of leaving them with a silent failure.
In power stations, water treatment plants and manufacturing facilities around the GCC, the same module is common on package units, burner management panels and compressor skids. Because the signal is a simple switching state, the KFD2-SOT2-Ex1.LB.IO is easy to commission, and spare units are often held on the shelf because a failed channel can stop a whole skid.
Selection and compatibility notes for KFD2-SOT2-Ex1.LB.IO
Check the sensor type first. The input is designed for NAMUR sensors according to EN 60947-5-6 and for mechanical contacts with the resistor network shown in the wiring diagram, so a three-wire sensor or a powered contact needs a different interface. Next check what the safe-area load requires, because a relay output and a transistor output behave very differently with PLC cards, solenoids and counters.
If the signal is part of a safety function, read the functional safety data in the datasheet, including the SIL value and the conditions attached to it, and compare it with your safety requirement specification. When the KFD2-SOT2-Ex1.LB.IO replaces an older module, compare terminal numbers and the supply arrangement, since the Power Rail option changes how power and the collective error message are wired.
Installation and commissioning of the KFD2-SOT2-Ex1.LB.IO
Before mounting the KFD2-SOT2-Ex1.LB.IO, confirm the field device and cable parameters against the entity values in the datasheet and the certificate, and decide whether the module will be powered from a Power Rail or from its own supply terminals. Mount it on a 35 mm DIN rail in a clean, ventilated cabinet in the safe area, keep hazardous-area and safe-area wiring physically separated and labelled, and respect the spacing and marking required by your site rules for intrinsically safe circuits. Confirm the switch position that sets output II as signal or fault output on the KFD2-SOT2-Ex1.LB.IO and write it on the terminal label.
Wire the KFD2-SOT2-Ex1.LB.IO only to the terminal assignment printed in the wiring diagram, tighten the screws and check that no strands are left outside the clamp. After applying the supply, check the power indication, then simulate the field signal and prove the complete loop from field to control system before the plant is handed over. Record the as-found readings so that later loop checks of the KFD2-SOT2-Ex1.LB.IO can be compared with the commissioning values.
Maintenance and service life
The KFD2-SOT2-Ex1.LB.IO has no serviceable parts, so maintenance is mostly inspection. During planned shutdowns, check terminals for looseness and corrosion, verify the supply voltage at the module, and repeat the loop check that was recorded at commissioning. In coastal and humid locations such as Muscat, Sohar and Duqm, a clean, dry and sealed cabinet greatly extends the life of any electronic interface. When a fault output is in use, treat its activation as a request to check the sensor cable first, since the KFD2-SOT2-Ex1.LB.IO detects both breakage and short-circuit on the input.
If a loop drifts out of tolerance or the unit shows no power indication with a healthy supply, replace the module instead of attempting a repair, and keep the replacement documentation in the loop folder. Certified intrinsically safe equipment must not be modified, and any change to cabling, load or field device should be re-assessed against the KFD2-SOT2-Ex1.LB.IO entity parameters before it returns to service.
Related products and ordering notes
Customers who ask for the KFD2-SOT2-Ex1.LB.IO often need neighbouring models or accessories from the same system, such as other KFD2, KFA6 and KHA6 switch amplifiers, NAMUR inductive sensors, the Power Rail and power feed modules, and the K-System accessories. If you are standardising a cabinet on one family, send us the loop list and we can quote the matching modules together.
When you send an enquiry for the KFD2-SOT2-Ex1.LB.IO, quote the full part number exactly as printed on the nameplate, the quantity and the intended application. If you are replacing an installed unit, a photograph of the nameplate helps us confirm the exact variant you need. We can arrange a quotation with delivery to Oman and across the GCC.
Frequently asked questions about KFD2-SOT2-Ex1.LB.IO
The KFD2-SOT2-Ex1.LB.IO is a SIL 2 one-channel switch amplifier with two passive transistor outputs, one of which can be configured as a fault indication output, and switching up to 5 kHz.
Documents and quotation
A copy of the manufacturer datasheet for the KFD2-SOT2-Ex1.LB.IO is attached to this page for your engineering review. To request a quotation, send the RFQ with the part number KFD2-SOT2-Ex1.LB.IO, the quantity, the delivery location and any certification or documentation requirements, and we will reply with availability and lead time. Please check the specification against your loop or system requirements before ordering.
Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with Pepperl+Fuchs. Product names and part numbers are used only to identify the item you ask for.
Other Models in the K System Range
Seven Star LLC supplies models from the K System range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Pepperl+Fuchs KFD2-STC4-Ex1 SMART Transmitter Power Supply | Isolator & Barrier | View details |
| Pepperl+Fuchs KFD2-STC4-Ex1.2O SMART Transmitter Supply, 2 Outputs | Isolator & Barrier | View details |
| Pepperl+Fuchs KFD2-CD-Ex1.32 Current Driver for I/P Converters | Isolator & Barrier | View details |
| Pepperl+Fuchs KFD2-CD-Ex1.32-13 Voltage Driver, 4-20 mA to 0-10 V | Isolator & Barrier | View details |
| Pepperl+Fuchs KFD2-UT2-Ex1-1 Universal Temperature Converter | Isolator & Barrier | View details |
| Pepperl+Fuchs KCD2-STC-Ex1.ES SMART Transmitter Supply, SIL 3 | Isolator & Barrier | View details |
| Pepperl+Fuchs KFD2-SOT2-Ex2.IO Switch Amplifier, 2-Ch Transistor | Isolator & Barrier | View details |
| Pepperl+Fuchs KFD2-SOT2-Ex1.LB.IO Switch Amplifier, 1-Ch Transistor | Isolator & Barrier | You are viewing this model |
Datasheets & Documents
- Datasheet KFD2-SOT2-Ex1.LB.IO Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Pepperl+Fuchs is a German manufacturer of industrial sensors and explosion protection equipment, founded in 1945 in Mannheim by Walter Pepperl and Ludwig Fuchs as a radio repair shop. Defective transformers led them into manufacturing, and the company developed its first proximity switch in the late 1950s. Pepperl+Fuchs is headquartered in Mannheim and is a pioneer of intrinsically safe electrical equipment for hazardous areas.
Seven Star LLC lists Pepperl+Fuchs sensors, isolated barriers, power supplies and hazardous-area mobile devices, and supplies them to instrument and automation teams in Oman by exact model designation.
Pepperl+Fuchs company profile
| Founded | 1945, Mannheim-Sandhofen, Germany, by Walter Pepperl and Ludwig Fuchs |
|---|---|
| Headquarters | Mannheim, Germany |
| Ownership | Privately owned (Pepperl+Fuchs SE) |
| Origins | Radio repair workshop that began making replacement transformers |
| Product families | Inductive, capacitive, ultrasonic and photoelectric sensors, rotary encoders, R2000 LiDAR scanners, KFD and HiC isolated barriers, Zener barriers, remote I/O, purge and pressurization systems, Ex-rated enclosures |
Milestones
- 1945: Walter Pepperl and Ludwig Fuchs open their radio repair shop in Mannheim.
- 1958: The first proximity switch is developed (some company sources say 1959).
Pepperl+Fuchs product families on this page
On the interface side there are two systems. The K-System mounts on DIN rail and is represented here by the KFD2-UT2-Ex2 universal temperature converter. The H-System plugs into termination boards and is represented by the HiD2030 SMART transmitter power supply with HART. The PS1000-A6-24.20 is a 24 VDC, 20 A power supply for cabinets. Sensors listed include the NJ2-12GK-SN NAMUR inductive sensor, the R101 retro-reflective photoelectric sensor and the R2000 2-D LiDAR scanner. For field staff there are the Tab-Ex 05 DZ1 tablet for Zone 1/21 areas and the Smart-Ex 03 DZ2 smartphone for Zone 2/22 and Division 2 areas.
Where Pepperl+Fuchs equipment is used
Isolated barriers sit between field instruments in Zone 0 or Zone 1 and the DCS or safety system in refineries, gas plants and chemical works. NAMUR sensors report valve position and machine states in classified areas. Photoelectric sensors and LiDAR scanners work in conveying, packaging, warehousing and vehicle guidance. Ex-rated tablets and phones are carried on operator rounds and maintenance jobs.
Pepperl+Fuchs products we list
Ordering Pepperl+Fuchs parts: what we need
Send the complete model designation as printed on the device, including every suffix; a single letter can change the supply voltage or the output type. Add the part number if the label shows one. For barriers, tell us the field device and signal type, the number of channels and whether the safety loop needs a SIL-assessed module. For mobile devices, state the zone or division and the regional radio version.
Facts checked against Pepperl+Fuchs's own chronicle pages, October 2026.
Browse Pepperl+Fuchs products by category: Sensors & Transmitters, Industrial Computer, Isolator & Barrier, Power Modules.
FAQ
Questions about the Pepperl+Fuchs KFD2-SOT2-Ex1.LB.IO Switch Amplifier,
Answers from our engineering team on installation, compatibility and integration.
01What is special about the KFD2-SOT2-Ex1.LB.IO?
One input drives two passive transistor outputs, and the second output can be set as a signal output or as a fault indication output.
02What kind of sensors does it accept?
It accepts NAMUR sensors according to EN 60947-5-6 and dry contacts with the resistor network shown in the wiring diagram.
03What switching current is possible?
Each transistor output can switch up to 100 mA at up to 30 V and is short-circuit protected.
04What SIL level is stated for the KFD2-SOT2-Ex1.LB.IO?
The datasheet states SIL 2 according to IEC/EN 61508.
05How do I order the KFD2-SOT2-Ex1.LB.IO?
Send an RFQ with the part number KFD2-SOT2-Ex1.LB.IO, the quantity and the delivery location, and Seven Star LLC will reply with availability and lead time.


















Reviews
There are no reviews yet.