Brand:

GESTRA UNA 39 Ball Float Steam Trap PN 160 / Class 900-1500

Description

UNA 39: GESTRA ball float trap for PN 160 and Class 1500 steam

At the top of the UNA ball float range, the GESTRA UNA 39 is a steam trap for very high pressures. It is rated PN 160 / Class 900 / Class 1500 in DN 15, 20, 25, 40 and 50, with a body of 1.7335 (A182-F12) alloy steel and a control unit with orifice up to 140 MAX. The datasheet quotes admissible differential pressures of 80, 110 and 140 bar depending on the orifice, equal to 1160, 1595 and 2030 psi.

Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. This page paraphrases the manufacturer’s datasheet; confirm all values against the current document before ordering.

Control and orifice choices for UNA 39

The UNA 39 is supplied with a SIMPLEX control unit: a level-dependent float controller. It works with a pilot valve and a main valve in the way the UNA 3.. series is described: the float senses the condensate level and the pilot opens and closes the main valve through a control chamber and bellows. The orifice table lists the choices and the hole diameter in millimetres.

Parameter Value
Orifice Hole diameter / max. differential pressure
80 1.9 mm / 80 bar (1160 psi)
110 1.6 mm / 110 bar (1595 psi)
140 1.4 mm / 140 bar (2030 psi)
140 MAX 6.5 mm / 140 bar, for large flowrates

UNA 39 ratings

Parameter Value
Type GESTRA UNA 39, ball float steam trap
Sizes DN 15, 20, 25, 40, 50
Rating PN 160 / Class 900 / Class 1500
EN flange pressure 160 barg at -10/300 °C; 134.8 at 450 °C; 104.3 at 500 °C; 71.6 at 520 °C; 46.4 at 540 °C; 37.3 at 550 °C
Class 900 flange 155 barg at -10/100 °C; 117 at 350 °C; 84.6 at 500 °C; 33.6 at 550 °C
Weld ends Socket-weld ends to ASME B16.11 Class 6000; butt-weld ends EN 12627
Body 1.7335 / A182-F12
Cover 1.7335 / A182-F12
Studs and nuts 1.7709
Gasket Graphite/CrNi
Internals Stainless steel
Control unit SIMPLEX with orifice 80, 110, 140 or 140 MAX

Where the UNA 39 differs from the UNA 38

The change from the UNA 38 is first in material: the UNA 38 body is 1.5415 and its cover 1.7357, but the UNA 39 uses 1.7335 for both body and cover, which holds its rating to 550 °C. Second, pressure class: PN 160 and Class 900 or 1500 against PN 100 and Class 600. Third, differential pressure: up to 140 bar against up to 80 bar. Fourth, control units: only SIMPLEX is listed for the UNA 39, so deaeration with a DUPLEX unit is not a choice. Dimensions also change: socket-weld versions have L1 of 170 mm and butt-weld versions L2 of 240 mm, with some DN 50 versions longer at 245 and 315 mm.

Applications for UNA 39

Trap duty at 100 to 160 bar is unusual, and appears in supercritical or high-pressure boiler drains, steam separators, main steam line warm-up drains and high-pressure process steam in refineries and power stations. The float design gives continuous discharge that is not affected by back pressure. Be sure that the application needs this class of equipment; for standard steam pressures a trap in the PN 40 range is more economical.

Reading the UNA 39 rating tables

For EN flanges to EN 1092-1 and for socket-weld and butt-weld ends, the datasheet gives 160 barg at temperatures up to 300 °C, 134.8 barg at 450 °C, 104.3 barg at 500 °C and 37.3 barg at 550 °C, which is 2320 psig falling to 541 psig. For ASME Class 900 flanges the maximum is 155 barg at 100 °C. The differential pressure is a separate figure, limited by the orifice, and is not reduced by temperature in the tables. The UNA 39 is supplied with the SIMPLEX control unit only, so air is removed through the hand-vent valve that the datasheet lists with that unit and not through an automatic bimetallic vent, which suits a trap that works on high-pressure condensate.

Installing and servicing UNA 39

Choose flange, socket-weld or butt-weld ends according to the piping class and weld procedure. Socket-weld versions are listed to Class 6000. Plan lifting equipment and supports, since the body is large for a DN 15-50 trap. Spare control units and gaskets should be kept in stock where an unplanned outage would be costly.

Size and weight of UNA 39

The datasheet dimension tables show how large these traps are. Flanged versions in DN 15 to DN 25 weigh 38 kg and have a length of 300 mm for the UNA 38; for the UNA 39 the lengths depend on the connection and range from 170 mm for socket-weld versions to 350 mm for some ASME flanged versions. Drawings show the body, control unit, cover and flow direction. Allow generous maintenance space around the cover for removing the control unit. The weight and size mean that pipe supports and a hoist point should be planned at the design stage and not left to site decisions.

Selection steps for UNA 39

Gather inlet pressure and temperature, back pressure, expected condensate rate and fluid. Check the flange rating at the operating temperature, then match the orifice to the actual differential pressure with margin below the limit. If the differential is below 80 bar, a UNA 38 may be sufficient and easier to source.

Documents and quotation

The UNA 39 datasheet is available on this page. Send an RFQ with part number UNA 39, orifice, connection and quantity; we will respond with availability for Oman and the GCC.

Delivery to Sites in Oman and the GCC

Delivery of the GESTRA UNA 39 is arranged to suit the site, whether that is a plant in Sohar or Duqm, an oilfield location in the interior, or a project elsewhere in the GCC. Tell us the delivery point, any site access or gate-pass requirements, and the person who will receive the goods. Goods are packed to protect sensitive steam traps & steam specialties equipment during road or air transport, and shipping details are shared once the order is dispatched so that your stores team can plan receipt and inspection.

Selection Notes for the GESTRA UNA 39

When comparing the GESTRA UNA 39 with alternatives, start from the duty it must perform: the measured or controlled variable, the range and accuracy you need, the environment at the mounting point and the interface to your control system. Check the electrical and mechanical connections against the installed equipment, and confirm any hazardous-area or ingress-protection requirements for the location. If any point is unclear, send a photo of the nameplate and a short description of the application, and we will compare it with the GESTRA steam traps & steam specialties range and confirm the correct order code before you commit.

Datasheets & Documents
  • PDF Datasheet GESTRA UNA 39 Ball Float Steam Trap PN 160 / Class 900-1500 Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

GESTRA is the German steam and condensate specialist behind the UNA ball float steam traps, the MPA blowdown valves and a long line of boiler level and conductivity controls. It was founded in Bremen in 1902 by Gustav F. Gerdts, and has been part of Spirax Sarco since 2017.

Seven Star LLC is an independent supplier in Muscat. We list GESTRA steam traps, blowdown valves and boiler control equipment, and supply GESTRA parts and spares to boiler houses and process plants in Oman and the GCC.

GESTRA company profile

Established 29 October 1902, Bremen, Germany, by Gustav Friedrich Gerdts; renamed Gustav F. Gerdts KG in 1907
Ownership history Became a stock corporation (GESTRA AG) in 1987, was taken over by Flowserve in 2002, and has been part of the Spirax Sarco group since 2017
Product families Steam traps, non-return and check valves, boiler blowdown valves, control valves, and boiler control electronics for level, conductivity and temperature
Applications Steam boilers, steam distribution and condensate return in process plants, power stations, hospitals, food and textile plants

Milestones

  • 1902: Gustav Friedrich Gerdts founds the company in Bremen on 29 October.
  • 1907: The company is renamed Gustav F. Gerdts KG.
  • 1987: It becomes a stock corporation, GESTRA AG.
  • 2002: Flowserve takes over GESTRA.
  • 2017: GESTRA becomes part of the Spirax Sarco group.

GESTRA products we list

Series Type What it does
UNA 45, UNA 16, UNA 38 Ball float steam traps Continuous condensate discharge from heat exchangers and process equipment; the UNA 38 is the high-pressure version (PN 100)
BK 45 Bimetallic steam trap Robust trap for steam main drainage and tracing, resistant to water hammer
MK 45, TK 23, SMK 22-81 Thermostatic steam traps Air venting and condensate discharge; the SMK 22-81 is the sanitary version for clean steam
MPA 46 Rapid-action blowdown valve Short, intermittent bottom blowdown that removes sludge from the boiler
NRS 1-54, NRR 2-50, NRR 2-60, NRGT 26-2 Boiler level controls Water level limiting, feedwater control and continuous level measurement
LRGT 16-1, LRR 1-50 Conductivity measurement and control Keeps boiler water conductivity in range through continuous blowdown
TRS 5-50 Safety temperature limiter SIL 3 temperature limiting for boilers and hot water systems

The type of steam trap follows the duty. Ball float traps discharge condensate as soon as it forms, which suits heat exchangers with changing loads. Thermostatic and bimetallic traps hold condensate back slightly and suit steam mains, tracing and air venting. On the boiler itself, GESTRA level and conductivity electronics work as a system: electrodes or transmitters in the boiler, controllers in the panel, and the feedwater and blowdown valves they drive.

Where GESTRA products are used

In Oman and the GCC, GESTRA equipment is used in boiler houses of refineries, petrochemical and fertiliser plants, power and desalination stations, food and beverage plants, laundries, hotels and hospitals.

Ordering GESTRA parts: what we need

Send the type designation, pressure rating (PN) and connection size (DN), the end connection (flanged, screwed or socket weld), the operating pressure and condensate load for steam traps, and the supply voltage and bus type (CAN bus, 4-20 mA) for control equipment. For electrodes, add the insertion length.

Facts checked against GESTRA company history and Bremen city records, October 2026.

FAQ

Questions about the GESTRA UNA 39 Ball Float Steam Trap PN 160 / Class

Answers from our engineering team on installation, compatibility and integration.

01What is the pressure class of the UNA 39?
PN 160 / Class 900 / Class 1500 in DN 15 to DN 50, with a 1.7335 (A182-F12) body.
02What orifices does the UNA 39 have?
Orifice 80, 110, 140 and 140 MAX, with differential pressure limits of 80, 110 and 140 bar.
03Is a DUPLEX control unit available for the UNA 39?
The datasheet lists only the SIMPLEX control unit for the UNA 39; the DUPLEX unit is listed for the UNA 38.
04How does the UNA 39 differ from the UNA 38?
It has a PN 160 / Class 900-1500 rating, 1.7335 body and cover, and differential pressures up to 140 bar instead of 80 bar.
05What end connections exist for the UNA 39?
EN and ASME flanges, socket-weld ends to ASME B16.11 Class 6000 and butt-weld ends to EN 12627.