Brand:

Festo DNC-32-100-PPV-A ISO 15552 Cylinder

Description

DNC-32-100-PPV-A: Festo 32 mm bore, 100 mm stroke ISO 15552 profile-barrel cylinder

The Festo Festo DNC-32-100-PPV-A (Festo part number 163309) is a double-acting ISO 15552 profile-barrel cylinder with a 32 mm piston and a 100 mm stroke, built to ISO 15552. At 6 bar it develops a theoretical 483 N on the advance stroke and 415 N on the return stroke, uses adjustable pneumatic cushioning at both ends, and has a male thread piston rod end with M10x1.25 thread. Seven Star LLC supplies the Festo DNC-32-100-PPV-A in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.

How to read the DNC-32-100-PPV-A type code

Every element of the type code carries a design decision. Reading it left to right avoids ordering the wrong sibling:

  • DNC: Festo standards-based (profile barrel) cylinder series
  • 32: piston diameter 32 mm
  • 100: stroke 100 mm
  • PPV: adjustable pneumatic cushioning at both ends
  • A: position sensing via proximity switch available (magnet on the piston)

The datasheet remains the reference. If a type code on a nameplate differs from the code in an enquiry, send us the nameplate photo and we will confirm before quoting.

Festo DNC-32-100-PPV-A technical specifications

Parameter Specification
Manufacturer / part number Festo DNC-32-100-PPV-A (Festo part number 163309)
Product type ISO cylinder
Stroke 100 mm
Piston diameter 32 mm
Piston rod thread M10x1.25
Cushioning Pneumatic cushioning, adjustable at both ends
Mounting position Any
Conforms to standard ISO 15552
Piston-rod end Male thread
Design Piston; Piston rod; Prole barrel
Position detection Via proximity switch
Variants Piston rod at one end
Operating pressure 0.06 MPa to 1.2 MPa; 0.6 bar to 12 bar
Mode of operation Double-acting
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on operating and pilot medium Lubricated operation possible (in which case lubricated operation will; always be required)
Corrosion resistance class CRC 2 – Moderate corrosion stress
LABS (PWIS) conformity VDMA24364-B1/B2-L
Ambient temperature -20 °C to 80 °C
Impact energy in end positions 0.1 J
Cushioning length 20 mm
Theoretical force at 0.6 MPa (6 bar, 87 psi), return stroke 415 N
Theoretical force at 0.6 MPa (6 bar, 87 psi), advance stroke 483 N
Moving mass for 0 mm stroke 162 g
Additional moving mass per 10 mm stroke 9g
Basic weight for 0 mm stroke 517 g
Additional weight per 10 mm stroke 30 g
Type of mounting With female thread; With accessories
Pneumatic connection G1/8
Note on materials RoHS compliant
Material cover Die-cast aluminium; coated
Material seals TPE-U(PU)
Material piston rod High-alloy steel
Material cylinder barrel Wrought aluminium alloy; Smooth-anodised

Working principle and cushioning of the DNC-32-100-PPV-A

Compressed air admitted to one side of the piston pushes it while the opposite chamber exhausts; reversing the supply reverses the movement. Because the effective piston area on the rod side is smaller, the DNC-32-100-PPV-A produces 483 N advancing but 415 N on return at 6 bar, a difference of roughly 14 percent that matters for pulling loads. The cushioning is adjustable at both ends: a trapped air cushion decelerates the piston over 20 mm and screws let the commissioning technician trade stopping time against smoothness. The datasheet gives an impact energy of 0.1 J in the end positions, which sets the limit for moved mass and speed. A magnet on the piston allows the position to be read by proximity switches mounted on the barrel, so end positions can be monitored without any change to the cylinder.

Mass, weight and force data for sizing the DNC-32-100-PPV-A

The moving mass is 162 g for 0 mm stroke plus 9 g per additional 10 mm, giving about 252 g at 100 mm; the product weight is 517 g plus 30 g per 10 mm, about 817 g at 100 mm. These figures help to check carrying structures, to estimate the kinetic energy at the end of the stroke and to confirm that a mounting bracket is rated for the cylinder. Remember that the quoted forces are theoretical values at 6 bar; friction and seal drag reduce them in practice, so a safety margin is normal in sizing. The permitted operating pressure range is 0.6 bar to 12 bar, with an ambient temperature range of -20 °C to 80 °C.

Where the DNC-32-100-PPV-A fits: related Festo parts

The DNC range is another Festo ISO 15552 cylinder series, in the same mounting-dimension class as the DSBC. Sibling codes include DNC-32-100-PPV-A, DNC-40-100-PPV-A, DNC-50-100-PPV-A, DNC-63-100-PPV-A, DNC-80-100-PPV-A, DNC-100-100-PPV-A and the DNC-50-100-PPV version without position sensing. Around the DNC-32-100-PPV-A you typically need foot, flange or clevis mountings, rod-end couplers, magnetic proximity switches, push-in fittings for the G1/8 port and a pressure regulator with filter. Send us the complete bill of materials if you want these items quoted together.

Part number Bore Stroke Advance force at 6 bar Cushioning Port
DNC-32-100-PPV-A 32 mm 100 mm 483 N Pneumatic cushioning, adjustable at both ends G1/8
DNC-40-100-PPV-A 40 mm 100 mm 754 N Pneumatic cushioning, adjustable at both ends G1/4
DNC-50-100-PPV-A 50 mm 100 mm 1178 N Pneumatic cushioning, adjustable at both ends G1/4
DNC-63-100-PPV-A 63 mm 100 mm 1870 N Pneumatic cushioning, adjustable at both ends G3/8
DNC-80-100-PPV-A 80 mm 100 mm 3016 N Pneumatic cushioning, adjustable at both ends G3/8
DNC-100-100-PPV-A 100 mm 100 mm 4712 N Pneumatic cushioning, adjustable at both ends G1/2
DNC-50-100-PPV 50 mm 100 mm 1178 N Pneumatic cushioning, adjustable at both ends G1/4

Selection and ordering checklist for DNC-32-100-PPV-A

Choose this size for loads in the 480 N range at 6 bar on the advance stroke and for the compact 32 mm footprint.

  • Bore and force: confirm that 483 N advance and 415 N return at your operating pressure, after friction losses, cover the load with margin.
  • Stroke: 100 mm is fixed in this code; a different stroke is a different part number.
  • Rod end: male thread with M10x1.25 thread; check that your coupler or clevis matches.
  • Cushioning: adjustable pneumatic cushioning at both ends; confirm this matches the moved mass and speed.
  • Sensing: magnetic proximity switches can be fitted; confirm sensor type separately.
  • Connection: G1/8 on both end covers; confirm the fittings and tube size.
  • Environment: ambient range -20 °C to 80 °C; avoid aggressive media and welding spatter on the rod.

Installation, commissioning and maintenance of the DNC-32-100-PPV-A

Mount the cylinder so that the load is guided and the rod sees axial force only; side loads on the rod bearing are the most common cause of early wear. Supply clean, dry compressed air at the quality stated in the datasheet (ISO 8573-1 class [7:4:4]) and fit a filter-regulator upstream. Open the supply gradually, then adjust the cushioning screws at both ends until the piston arrives softly without bouncing. The datasheet notes that lubricated operation is possible but, once started, must be continued, so decide on lubrication at commissioning and keep to it. Inspect the wiper and piston rod surface during scheduled shutdowns, and keep spare seals or a complete spare cylinder for critical lines.

Typical applications of the DNC-32-100-PPV-A in Oman and the GCC

The 32 mm bore with 100 mm stroke is one of the most common ISO 15552 sizes in light assembly, welding fixtures, packaging machinery and test rigs. A Muscat workshop will typically find this size already in the plant spares list, which makes it a frequent replacement target. Plants in Oman and the wider GCC add extra demands: ambient heat, dust, humidity near the coast and long maintenance intervals. Check the temperature range in the table above, protect the rod from sand and abrasive dust with a bellows where needed, and ensure the compressed air is well dried so that moisture does not reach the cylinder.

Information to send with an RFQ for DNC-32-100-PPV-A

  • Full type code: DNC-32-100-PPV-A (and Festo part number 163309 if known).
  • Quantity and required delivery timeframe.
  • Machine or plant where the part will be fitted, and whether it is a replacement or a new design.
  • Nameplate photo of the existing cylinder if it is a replacement.
  • Mounting accessories, proximity switches and fittings required alongside.
  • Delivery destination in Oman or the GCC.

Documents and quotation

A datasheet for the DNC-32-100-PPV-A is attached on this page for reference. It lists the technical data shown above; check any application-specific limit against the document before committing to a design.

To request a quotation, send the part number DNC-32-100-PPV-A, the quantity and the delivery location. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer.

Datasheets & Documents
  • PDF Datasheet Festo DNC-32-100-PPV-A Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Festo is a German maker of pneumatic and electric automation technology, founded in 1925 in Esslingen am Neckar by Albert Fezer and Gottlieb Stoll; the name comes from their surnames. It first made woodworking machines and power tools before moving into pneumatics in the 1950s. Festo is family-owned and still headquartered in Esslingen.

Seven Star LLC sources and supplies Festo cylinders, valves and valve terminals for machine maintenance and projects in Oman and the GCC.

Festo company profile

Founded 1925, Esslingen am Neckar, Germany
Founders Albert Fezer and Gottlieb Stoll
Name From FEzer and STOll
Headquarters Esslingen am Neckar
Ownership Family-owned
Product families DSBC and ADN pneumatic cylinders, VUVG and VTUG solenoid valves and valve terminals, MS series air preparation units, CPX-AP remote I/O, EMMT servo motors and CMMT servo drives, electric axes and grippers

Milestones

  • 1925: Fezer and Stoll found the company in Esslingen.
  • 1950s: Festo begins making pneumatic components.

Festo products listed

Two items show the two halves of a pneumatic circuit. The VTUG is a valve terminal: a manifold that carries a row of directional valves with common air supply and a shared electrical connection. The DSBC-32-100-PPVA-N3 is an ISO standard cylinder. Its type code reads as 32 mm piston diameter and 100 mm stroke, with adjustable end-position cushioning and a piston magnet for position sensing.

Festo products we list

Family Examples
Automation Accessories KMP3-9P-08-5 Connecting Cable, KMPYE-AIF-1-GS-GD-2 Cable
Pneumatic Cylinders ADN-100-30-A-P-A Compact Cylinder
Valve Actuators DSBC-32-100-PPVA-N3 ISO Cylinder
Pressure Instrumentation VPEV-1/8 Pressure Switch
Solenoid Valves VTUG Valve Terminal

Ordering Festo parts: what we need

Festo parts carry both a type code and a numeric part number on the label. Send both when you can; the part number is the shortest route to an exact match. For a cylinder give the full type code as on the listed DSBC example, plus mounting parts and proximity switches if required. For a VTUG valve terminal send the configuration code or a label photo: number of valve positions, valve functions, coil voltage and the electrical connection type all vary from one terminal to the next.

Facts checked against Festo's corporate history pages, October 2026.

FAQ

Questions about the Festo DNC-32-100-PPV-A ISO 15552 Cylinder

Answers from our engineering team on installation, compatibility and integration.

01What force does the DNC-32-100-PPV-A produce?
At 6 bar the datasheet gives a theoretical 483 N on the advance stroke and 415 N on the return stroke. Real forces are lower because of friction, so keep a safety margin when sizing the load.
02What are the operating pressure and temperature limits of the DNC-32-100-PPV-A?
The operating pressure range is 0.6 bar to 12 bar and the ambient temperature range is -20 deg C to 80 deg C. Operation outside these limits is not covered by the datasheet.
03How is the end position of the DNC-32-100-PPV-A cushioned?
The datasheet lists: Pneumatic cushioning, adjustable at both ends. The permitted impact energy in the end positions is 0.1 J, which limits the moved mass and speed without an external damper.
04Can proximity switches be fitted to the DNC-32-100-PPV-A?
Yes. The datasheet lists position detection via proximity switch, so magnetic switches can be mounted on the barrel. The switches themselves are separate items.
05What port and rod thread does the DNC-32-100-PPV-A have?
The pneumatic connection is G1/8 and the piston rod end is a male thread with M10x1.25 thread, per the datasheet. Confirm these against your fittings and couplers before ordering.