Schneider Electric EZ9R36263 Easy9 2P 63 A 30 mA RCCB

EZ9R36263: Easy9 2P 63 A 30 mA type AC RCCB

The EZ9R36263 is a Schneider Electric Easy9 residual current circuit breaker (RCCB): two-pole, opens phase and neutral together, for a single-phase circuit. Its rated current is 63 A, its earth-leakage sensitivity is 30 mA with instantaneous tripping, and the protection class is type AC. It clips onto a DIN rail, occupies 4 modules of 9 mm (36 mm) and is rated 230 V AC at 50/60 Hz. Seven Star LLC supplies the EZ9R36263 in Oman and the GCC as an independent supplier based in Muscat.

The reference reads as EZ9R, then 3 for 30 mA, then 6, then 2 for the pole count and 63 for the rated current in amperes. That is our reading of the pattern across the twelve Easy9 RCCB references we looked at, not a published ordering table, so confirm the complete reference before you order.

Technical specifications of the EZ9R36263

How the EZ9R36263 detects earth leakage

Inside an RCCB the live conductors pass through a sensing core. When current out and current back are equal the core sees nothing, and when part of it leaves by another path, such as through a person or a damaged cable to earth, the imbalance appears. At 30 mA the EZ9R36263 opens all 2 poles. The datasheet lists voltage-independent tripping, so the mechanism does not rely on the line voltage to act.

The device is type AC, which responds to sinusoidal alternating residual current. Loads that can put a smooth or pulsating DC component into a fault, such as some drives, chargers and rectifier supplies, need a type A or better device, and the protection class on this reference should be compared with those loads before it is chosen.

An RCCB gives no overload or short-circuit protection. The datasheet figure for conditional short-circuit current assumes the proper protective device ahead of the EZ9R36263, which should not be rated above 63 A.

Why 30 mA on the EZ9R36263

The EZ9R36263 has a 30 mA threshold, the figure normally associated with supplementary protection of people on socket and final circuits. All leakage downstream adds up, including the small leakage that filters and electronic supplies send to earth, so a board with many such loads on one RCCB can drift toward the trip level. Splitting circuits across several RCCBs, or moving to a less sensitive stage where the protection goal allows it, is the usual remedy.

Instantaneous tripping, as listed here, means there is no built-in delay. When several residual current devices are cascaded, a downstream fault can trip the upstream device at the same time unless it is a selective type, so plan the board structure with that in mind.

Durability and environment for the EZ9R36263

The datasheet lists 5000 mechanical cycles and 2000 electrical cycles at 230 V AC, IP20 protection, pollution degree 2, tropicalisation 2 and 95 % relative humidity at 55 °C. Operation is listed from -5 to 60 °C and storage from -40 to 85 °C.

The upper operating limit of 60 °C is well above typical indoor room air, but a closed board in an Omani summer runs hotter than the room, so leave ventilation and distance from contactors and busbars around this RCCB.

Installing and testing the EZ9R36263

Isolate and prove dead, clip the this RCCB onto the DIN rail, connect the conductors observing the neutral position and tighten to 3.5 N.m. After energising, operate the test button on the front. The device must trip immediately, and the toggle is then reset by hand. A device that does not trip on test should be replaced instead of reset.

Operate the test button at regular intervals in service and record the rating and sensitivity on the board schedule. When an RCCB trips for real, look for the leakage before closing it again, because a repeated trip normally points to wet equipment, a damaged cable or an earth fault.

The EZ9R36263 among Easy9 RCCBs

Pole count sets the width and the voltage, the current rating sets how much load the device can carry, and sensitivity sets the leakage level at which it trips. The table compares neighbouring Easy9 references.

Selection checklist for the EZ9R36263

• Supply: 230 V AC, 2 poles, matching a single-phase circuit.
• Current: load through the device up to 63 A, with upstream protection no higher.
• Sensitivity: 30 mA against the goal of protecting people, equipment or the installation from fire.
• Waveform: type AC against the loads on the circuit.
• Backup: a miniature circuit breaker or fuse upstream, since the RCCB does not trip on overcurrent.
• Space: 4 modules, 36 mm of DIN rail.

Information to send with an RFQ for the EZ9R36263

• Exact reference EZ9R36263 and the quantity needed.
• Supply voltage, system type and earthing arrangement.
• Description of the loads, including drives or electronic equipment.
• Upstream protective device and its rating.
• Other poles, ratings or sensitivities needed in the same order.
• Delivery location and timeline.

Before ordering, check that the board enclosure, busbar arrangement and neighbouring devices leave enough room for heat to escape, since crowded boards in hot rooms run closer to their limits than the rated ambient suggests.

Keep a record of the installed ratings on the board schedule and note the supply voltage at commissioning, because later extensions and fault investigations depend on knowing exactly what protects each circuit.

Spare devices of the same rating, pole count and sensitivity are worth planning for sites that run continuously, since a like-for-like replacement keeps the original protection design intact after a trip or a fault.

If the board will be extended later, leave spare rail length and think about how added circuits change the leakage current seen by this device, which affects how close it runs to its trip threshold.

Documents and quotation

The Schneider Electric datasheet for the EZ9R36263 is attached on this page and holds the full specification summarised above. It is dated 8 Nov 2026 as printed on the manufacturer’s document.

Send us the reference EZ9R36263, quantity and delivery location and Seven Star LLC will reply to your request. We supply as an independent supplier based in Muscat and do not act for the manufacturer.