Brand:

Carlo Gavazzi RSGT4025E0V10C 25 A Three-Phase Soft Starter

Description

A compact 25 A soft starter with overload protection and Modbus

The RSGT4025E0V10C is a three-phase soft starter for AC induction motors from the Carlo Gavazzi RSGT range. It is rated 25 A (rms) at 40 degC for 220 to 400 V AC supplies, built into a 45 mm wide housing, and takes a 110 to 400 V AC control signal on terminals A1-A2. Class 10 electronic overload protection and a Modbus RTU port are built in.

The RSGT sets its own start parameters. A self-learning algorithm adjusts current limit and ramp to keep the actual start time close to the ramp-up setting, so only three selectors need to be set: full-load current (FLC), ramp-up time and ramp-down time. During ramp-down it uses torque control for a smoother stop, which helps pumps where hydraulic hammer is a concern. Wrong phase sequence detection, dry-run detection for pumps and an alarm relay are included, so separate monitoring relays may not be needed in the same panel.

Technical specifications

Parameter Specification
Order code RSGT4025E0V10C
Decoding RSGT = three-phase general purpose soft starter; 40 = 220 to 400 V AC; 25 = 25 A rms; E0 = 110 to 400 V AC control voltage, internally supplied; V1 = integrated motor overload protection (Class 10); 0 = no PTC; C = Modbus communication
Operational voltage 220 to 400 V AC (+10 %, -15 %); range 187 to 440 V rms; 50/60 Hz (plus or minus 10 %)
Rated operational current 25 A rms at 40 degC; 23 A at 50 degC; 21 A at 60 degC
Overload cycle AC53b: 3 to 12 : 288; maximum 12 starts per hour at 40 degC
FLC setting range 12 to 25 A
Ramp-up time / ramp-down time 1 to 20 s / 0 to 20 s; initial torque set automatically
Minimum load current 1 A rms
Control voltage (A1-A2) 110 to 400 V AC (+10 %, -15 %); range 93.5 to 440 V AC; pick-up below 80 V AC; drop-out above 20 V AC
Control input current 0.55 to 1.3 mA rms
Response time 200 ms (mains already present); 2 s with mains applied together with control
Blocking voltage / insulation 1200 Vp; rated insulation voltage 600 V AC; 2.5 kV rms supply to input and heatsink
Protection and diagnostics Class 10 electronic overload, wrong phase sequence detection, dry-run detection, integrated varistor
Auxiliary relays 2 outputs: alarm (NC) and bypassed / top of ramp (NO); 3 A at 250 V AC or 30 V DC
Communication Modbus RTU over RS485, 2 wires; address 1 to 247; 9.6, 19.2 or 38.4 kbit/s
Motor rating (product page) 5.5 kW at 230 V; 11 kW at 400 V; internal bypass
Housing PA66, DIN rail (EN 50022) or panel mount, IP20; 45 mm wide, about 125 mm high and 150 mm deep (product page); 0.5 to 0.75 kg
Working / storage temperature -20 to +60 degC (derating above 40 degC) / -40 to +80 degC
Altitude / pollution degree 1000 m / 2; installation category III
Standards and approvals EN 60947-4-2 (LVD, EMCD); UL 60947-4-2 and cUL (E172877)

Sizing the RSGT for a motor

The datasheet gives a selection guide for 220 to 400 V motors by full-load current and overload class: for example, a 22 A motor (about 11 kW at 400 V) is covered by the RSGT4025 at Trip Class 5 and 10, while the same motor at Trip Class 20 needs an RSGT4045. A 12 A motor (5.5 kW at 400 V) fits the RSGT4012 at Class 5 and 10 but needs an RSGT4025 at Class 20 and 30. Typical ramp settings are tabulated for compressors, pumps, fans, feeders and conveyors.

The nameplate current of the motor takes precedence over the table. For high inertia loads at Class 20 or 30 the datasheet recommends an external overload relay, and enough time between starts for the soft starter to cool.

Variants and what to confirm before ordering

The same range is available at 12, 16 and 25 A in the 45 mm housing, in 32, 45 and 55 A in a 75 mm housing and in 70 and 90 A in a 120 mm housing, with 24 V AC/DC control (F0) or 600 V versions (RSGT60). This 25 A code is the 400 V, 110 to 400 V control, Modbus version with no PTC input and no fan. Confirm supply voltage, control voltage, motor current and starting duty. For other soft starters on this site, see the Schneider Electric Altistart 22 or browse the motor soft starters category.

Related Carlo Gavazzi products: Carlo Gavazzi RGC1A60D25KKE 25 A Solid State Contactor, Carlo Gavazzi RM1A48D50 50 A 480 Vac Solid State Relay, Carlo Gavazzi EM340DINAV23XS1X Three-Phase Energy Meter RS485, Carlo Gavazzi EM540DINAV23XS1PFA Three-Phase MID Energy Analyzer, Carlo Gavazzi DPB01CM44 3-Phase Voltage Monitoring Relay and Carlo Gavazzi EM111DINAV81XS1X Single-Phase Energy Analyzer.

Documents and quotation

The official RSGT datasheet (Carlo Gavazzi document RSGT DS ENG, 09/09/2026) is attached. It contains the ordering code key, selection tables, settings, outputs, communication data, drawings and approvals. Send the order code, quantity and delivery location through the quotation form for availability from Seven Star LLC.

Datasheets & Documents
  • PDF Datasheet Carlo Gavazzi RSGT datasheet (EN, 09/09/2026) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Carlo Gavazzi is an international group making electronic components for industrial and building automation, founded in 1931 in Milan, Italy. The group's holding company, Carlo Gavazzi Holding AG, is based in Steinhausen, Switzerland, and has been listed on the SIX Swiss Exchange since 1996. Its sensors, relays and energy meters are used in machinery, HVAC, solar and building systems.

Seven Star LLC is an independent supplier in Muscat. We list Carlo Gavazzi components for panel builders and building services contractors in Oman and the GCC.

Carlo Gavazzi company profile

Founded 1931, Milan, Italy
Headquarters Steinhausen, Switzerland (Carlo Gavazzi Holding AG)
Listing SIX Swiss Exchange, since 1996
Markets Industrial automation and building automation
Product families RG and RM solid-state relays, CA capacitive and ICB inductive proximity sensors, DPA and DPB monitoring relays, EM24 and EM340 energy meters, Dupline field bus, timers and soft starters

Milestones

  • 1931: Carlo Gavazzi is founded in Milan.
  • 1996: Carlo Gavazzi Holding lists on the Swiss exchange.

Carlo Gavazzi product series

Energy meters include the EM340DINAV23XS1X three-phase meter with RS-485, the EM540DINAV23XS1PFA three-phase MID energy analyzer, the EM111DINAV81XS1X single-phase analyzer and the WM50AV53HBC multichannel power analyzer.

Switching and control includes the RM1A48D50 50 A solid state relay, the RGC1A60D25KKE 25 A solid state contactor, the RSGT4025E0V10C 25 A three-phase soft starter and the DPB01CM44 three-phase voltage monitoring relay. The ICB12S30N04NO is an M12 inductive proximity sensor.

Solid state relays and contactors switch heaters and other resistive loads silently and with long life, while soft starters reduce starting current and mechanical shock on pumps and fans. Carlo Gavazzi energy meters and analyzers are available with MID approval for billing and with Modbus RTU, Modbus TCP or M-Bus for building management systems.

Where Carlo Gavazzi products are used

Energy sub-metering in buildings, heating and process control with solid state switching, pump and fan soft starting, phase and voltage supervision of motors, and object detection on machines.

Carlo Gavazzi products we list

Family Examples
Automation Accessories DPB01CM44 3-Phase Voltage Monitoring Relay, EM111DINAV81XS1X Single-Phase Energy Ana…, EM340DINAV23XS1X Three-Phase Energy Mete…, EM540DINAV23XS1PFA Three-Phase MID Energ…, WM50AV53HBC Multichannel Power Analyzer
Contactors & Overload Relays RGC1A60D25KKE 25 A Solid State Contactor, RM1A48D50 50 A 480 Vac Solid State Relay
Inductive Proximity Sensors ICB12S30N04NO M12 Inductive Proximity Se…

Ordering Carlo Gavazzi products: what we need

Send the full ordering code, which defines input, supply, outputs and communication, or give the voltage, current, load type and interface needed.

Facts checked against Carlo Gavazzi Holding company profiles, October 2026.

FAQ

Questions about the Carlo Gavazzi RSGT4025E0V10C 25 A Three-Phase Soft

Answers from our engineering team on installation, compatibility and integration.

01What does the RSGT4025E0V10C do?
It soft starts and soft stops a three-phase AC motor up to 25 A, with Class 10 overload protection and Modbus RTU communication.
02What supply and control voltages does it use?
A 220 to 400 V AC power supply and a 110 to 400 V AC control signal on A1-A2.
03How is it set up?
With three selectors for motor FLC, ramp-up time and ramp-down time; a self-learning algorithm handles the rest.
04What protection is built in?
Class 10 electronic overload, wrong phase sequence detection and dry-run detection for pumps.
05How wide is it?
45 mm, for DIN rail or panel mounting.