- Automation & ControlView all 2,895 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- Pneumatic Cylinders
- HMI Displays
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: GESTRA
GESTRA DK 45 Thermodynamic Steam Trap with Strainer DN 15-25
Description
GESTRA DK 45 thermodynamic steam trap: how the disc works
The GESTRA DK 45 is a thermodynamic (disc) steam trap in a forged steel body with a permanently mounted cap, available in DN 15, 20 and 25 with flange, thread or weld ends. The datasheet describes it as a trap for discharging condensate with virtually no banking-up, with an integrated non-return valve, a Y-type strainer and an asbestos-free graphite body gasket. It can be installed in any position.
Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. The text below is drawn from the DK 45 datasheet; where the datasheet gives imperial units, we have kept them.
The cycle inside DK 45
A movable valve disc rests on a double seat. Condensate enters from below, lifts the disc off its seat, turns through 180 degrees and flows through the small seat orifice to the outlet. As the condensate gets hotter, pressure builds up above the disc. When the condensate flashes to steam a low-pressure area forms under the disc because of the increased flow velocity, and the disc is pulled down onto its seat. The pressure above acts on a larger area, so closing force exceeds the opening force from the inlet side. As steam in the cap space condenses, the pressure above the disc drops, the disc lifts again, and the cycle repeats.
Why the permanent cap matters for DK 45
Thermodynamic traps are often sensitive to external heat, wind and rain because the cap space needs to stay at a stable temperature. The datasheet states that the DK 45 is not influenced by such external factors because the regulator is protected by the permanently mounted cap. That is helpful in open, windswept pipe racks in coastal plants.
DK 45 technical data
| Parameter | Value |
|---|---|
| Type | GESTRA DK 45, thermodynamic steam trap |
| Sizes | DN 15, 20, 25 (1/2, 3/4, 1 inch) |
| Service pressure at 68 °F | 580 psig |
| Service pressure at 392 °F | 450 psig |
| Service pressure at 572 °F | 363 psig |
| Service pressure at 752 °F | 334 psig |
| Admissible differential pressure | 464 psig |
| Body and cap | 1.0460 / A 105 |
| Screws | 1.7225 / A 193 B 7 |
| Regulator and internals | Stainless steel |
| Gasket | Graphite, asbestos free |
| Flange options | EN 1092-1 PN 40, ASME B16.5 Class 150 and 300 |
| Flanged length | 150, 150, 160 mm; 3.7, 4.3, 4.8 kg |
| Threaded (BSP or NPT) | 95 mm; 2.2, 2.1, 2.0 kg |
| Butt-weld | 200 mm; 2.5 kg |
| Socket-weld | 95 mm; 2.2, 2.1, 2.0 kg |
How DK 45 differs from DK 47 and DK 57
The DK 47 and DK 57 listed in a separate datasheet are small stainless steel traps in sizes from 3/8 to 1 inch with screwed ends only and a 42 bar, 400 °C limit. The DK 45 is a forged steel trap with flanges, threads and weld ends in DN 15 to 25, a 580 psig rating at room temperature and an integrated non-return valve. If you need a flanged connection or an alloy-free carbon steel body for a larger bore line, the DK 45 is the one; for compact installs on tracing lines with threaded ends the smaller types apply.
Applications of DK 45
- Steam main drains in tank farms, where condensate collects at low points after pigging or shutdown.
- Process steam lines that run at constant pressure and need rugged drain points.
- Heated storage tanks and pipelines for fuel and chemicals where robust, simple traps are preferred.
Because the trap discharges condensate in short cycles, it is audible, and a gentle clicking is normal.
Reading the pressure and temperature curve of DK 45
The datasheet draws service pressure against inlet temperature in imperial units. At 68 °F the DK 45 is rated for 580 psig, and the allowed pressure then falls with temperature to 450 psig at 392 °F, 363 psig at 572 °F and 334 psig at 752 °F. The admissible differential pressure, which is inlet pressure minus outlet pressure, is 464 psig. In metric terms that is roughly 40 bar at ambient temperature, falling to about 23 bar at 400 °C, with a differential limit of about 32 bar. Use the curve for the actual steam temperature at the trap, not the nominal header temperature, since drip legs after pressure-reducing stations can run cooler or hotter than the main.
The datasheet also provides a capacity chart for hot condensate against differential pressure. Disc traps discharge intermittently, so the capacity shown is an average. If the load is small and the trap cycles slowly, that is normal; if it cycles quickly with little condensate, the disc may be worn.
Installing and maintaining DK 45
Fit the trap with the cap upward and keep the inlet line free of scale; the integral Y-strainer removes only larger debris. The datasheet gives flange diameters of 95, 105 and 115 mm for PN 40 and 88.9, 98.4 and 107.9 mm for Class 150. Butt-weld ends suit pipes 21.3 x 2.0, 26.9 x 2.3 and 33.7 x 2.6 mm. A short cycle time or continuous steam loss shows a worn disc or seat.
Weights for transport and support planning are 3.7, 4.3 and 4.8 kg for flanged DN 15, 20 and 25, about 2 kg for threaded and socket-weld versions, and 2.5 kg for butt-weld versions. Flange thicknesses b are 16, 18 and 18 mm on PN 40 and 11.1, 12.7 and 14.3 mm on Class 150, with four bolt holes in every case. The overall length follows ISO 6554, so the DK 45 can replace many existing flanged traps without pipe changes.
Documents and quotation
The datasheet for DK 45 is attached. To request a quote, send an RFQ with part number DK 45, quantity and connection type; we will answer with availability for Oman and the GCC.
Delivery to Sites in Oman and the GCC
Delivery of the GESTRA DK 45 is arranged to suit the site, whether that is a plant in Sohar or Duqm, an oilfield location in the interior, or a project elsewhere in the GCC. Tell us the delivery point, any site access or gate-pass requirements, and the person who will receive the goods. Goods are packed to protect sensitive steam traps & steam specialties equipment during road or air transport, and shipping details are shared once the order is dispatched so that your stores team can plan receipt and inspection.
Selection Notes for the GESTRA DK 45
When comparing the GESTRA DK 45 with alternatives, start from the duty it must perform: the measured or controlled variable, the range and accuracy you need, the environment at the mounting point and the interface to your control system. Check the electrical and mechanical connections against the installed equipment, and confirm any hazardous-area or ingress-protection requirements for the location. If any point is unclear, send a photo of the nameplate and a short description of the application, and we will compare it with the GESTRA steam traps & steam specialties range and confirm the correct order code before you commit.
Datasheets & Documents
- Datasheet GESTRA DK 45 Thermodynamic Steam Trap with Strainer DN 15-25 Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
GESTRA is the German steam and condensate specialist behind the UNA ball float steam traps, the MPA blowdown valves and a long line of boiler level and conductivity controls. It was founded in Bremen in 1902 by Gustav F. Gerdts, and has been part of Spirax Sarco since 2017.
Seven Star LLC is an independent supplier in Muscat. We list GESTRA steam traps, blowdown valves and boiler control equipment, and supply GESTRA parts and spares to boiler houses and process plants in Oman and the GCC.
GESTRA company profile
| Established | 29 October 1902, Bremen, Germany, by Gustav Friedrich Gerdts; renamed Gustav F. Gerdts KG in 1907 |
|---|---|
| Ownership history | Became a stock corporation (GESTRA AG) in 1987, was taken over by Flowserve in 2002, and has been part of the Spirax Sarco group since 2017 |
| Product families | Steam traps, non-return and check valves, boiler blowdown valves, control valves, and boiler control electronics for level, conductivity and temperature |
| Applications | Steam boilers, steam distribution and condensate return in process plants, power stations, hospitals, food and textile plants |
Milestones
- 1902: Gustav Friedrich Gerdts founds the company in Bremen on 29 October.
- 1907: The company is renamed Gustav F. Gerdts KG.
- 1987: It becomes a stock corporation, GESTRA AG.
- 2002: Flowserve takes over GESTRA.
- 2017: GESTRA becomes part of the Spirax Sarco group.
GESTRA products we list
| Series | Type | What it does |
|---|---|---|
| UNA 45, UNA 16, UNA 38 | Ball float steam traps | Continuous condensate discharge from heat exchangers and process equipment; the UNA 38 is the high-pressure version (PN 100) |
| BK 45 | Bimetallic steam trap | Robust trap for steam main drainage and tracing, resistant to water hammer |
| MK 45, TK 23, SMK 22-81 | Thermostatic steam traps | Air venting and condensate discharge; the SMK 22-81 is the sanitary version for clean steam |
| MPA 46 | Rapid-action blowdown valve | Short, intermittent bottom blowdown that removes sludge from the boiler |
| NRS 1-54, NRR 2-50, NRR 2-60, NRGT 26-2 | Boiler level controls | Water level limiting, feedwater control and continuous level measurement |
| LRGT 16-1, LRR 1-50 | Conductivity measurement and control | Keeps boiler water conductivity in range through continuous blowdown |
| TRS 5-50 | Safety temperature limiter | SIL 3 temperature limiting for boilers and hot water systems |
The type of steam trap follows the duty. Ball float traps discharge condensate as soon as it forms, which suits heat exchangers with changing loads. Thermostatic and bimetallic traps hold condensate back slightly and suit steam mains, tracing and air venting. On the boiler itself, GESTRA level and conductivity electronics work as a system: electrodes or transmitters in the boiler, controllers in the panel, and the feedwater and blowdown valves they drive.
Where GESTRA products are used
In Oman and the GCC, GESTRA equipment is used in boiler houses of refineries, petrochemical and fertiliser plants, power and desalination stations, food and beverage plants, laundries, hotels and hospitals.
Ordering GESTRA parts: what we need
Send the type designation, pressure rating (PN) and connection size (DN), the end connection (flanged, screwed or socket weld), the operating pressure and condensate load for steam traps, and the supply voltage and bus type (CAN bus, 4-20 mA) for control equipment. For electrodes, add the insertion length.
Facts checked against GESTRA company history and Bremen city records, October 2026.
Browse GESTRA products by category: Liquid Analysis Sensors.
FAQ
Questions about the GESTRA DK 45 Thermodynamic Steam Trap with Strainer
Answers from our engineering team on installation, compatibility and integration.
01How does the DK 45 close?
Flash steam under the disc lowers pressure and pulls it onto the seat, and pressure above the larger disc area holds it closed until condensate relieves the pressure.
02Is the DK 45 affected by weather?
The datasheet states it is not influenced by external factors because the regulator is protected by the permanently mounted cap.
03What is the maximum differential pressure?
The datasheet gives an admissible differential pressure of 464 psig, about 32 bar.
04What sizes does the DK 45 come in?
DN 15, 20 and 25 with PN 40 and Class 150 or Class 300 flanges, BSP or NPT threads, and butt-weld or socket-weld ends.
05Does the DK 45 have a strainer?
Yes, a Y-type strainer and an integrated non-return valve are listed.


















Reviews
There are no reviews yet.