- Automation & ControlView all 2,523 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- CCTV & Security
- Motor Soft Starters
- Safety Switches & Guard Locking
- Encoders
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Festo
Festo DSBC-40-100-PPSA-N3 ISO 15552 Cylinder
Description
DSBC-40-100-PPSA-N3: Festo 40 mm bore, 100 mm stroke ISO 15552 profile-barrel cylinder
The Festo DSBC-40-100-PPSA-N3 (Festo part number 1376907) is a double-acting ISO 15552 profile-barrel cylinder with a 40 mm piston and a 100 mm stroke, built to ISO 15552. At 6 bar it develops a theoretical 754 N on the advance stroke and 633 N on the return stroke, uses self-adjusting pneumatic end-position cushioning, and has a male thread piston rod end with M12x1.25 thread. Seven Star LLC supplies the DSBC-40-100-PPSA-N3 in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.
How to read the DSBC-40-100-PPSA-N3 type code
Every element of the type code carries a design decision. Reading it left to right avoids ordering the wrong sibling:
- DSBC: Festo standards-based (profile barrel) cylinder series
- 40: piston diameter 40 mm
- 100: stroke 100 mm
- PPSA: self-adjusting pneumatic end-position cushioning, with a magnet on the piston for position sensing via proximity switch
- N3: closing element of the type key, quoted exactly as printed on the datasheet
The datasheet remains the reference. If a type code on a nameplate differs from the code in an enquiry, send us the nameplate photo and we will confirm before quoting.
DSBC-40-100-PPSA-N3 technical specifications
| Parameter | Specification |
|---|---|
| Manufacturer / part number | Festo DSBC-40-100-PPSA-N3 (Festo part number 1376907) |
| Product type | ISO cylinder |
| Stroke | 100 mm |
| Piston diameter | 40 mm |
| Piston rod thread | M12x1.25 |
| Cushioning | Self-adjusting pneumatic end-position cushioning |
| Mounting position | Any |
| Conforms to standard | ISO 15552 |
| Piston-rod end | Male thread |
| Design | Piston; Piston rod; Prole barrel |
| Position detection | Via proximity switch |
| Variants | Piston rod at one end |
| Operating pressure | 0.06 MPa to 1.2 MPa; 0.6 bar to 12 bar |
| Mode of operation | Double-acting |
| Operating medium | Compressed air to ISO 8573-1:2010 [7:4:4] |
| Note on operating and pilot medium | Lubricated operation possible (in which case lubricated operation will; always be required) |
| Corrosion resistance class CRC | 2 – Moderate corrosion stress |
| LABS (PWIS) conformity | VDMA24364-B1/B2-L |
| Cleanroom suitability, measured according to ISO 14644-14 | Class 5 according to ISO 14644-1 |
| Ambient temperature | -20 °C to 80 °C |
| Impact energy in end positions | 0.7 J |
| Cushioning length | 19 mm |
| Theoretical force at 0.6 MPa (6 bar, 87 psi), return stroke | 633 N |
| Theoretical force at 0.6 MPa (6 bar, 87 psi), advance stroke | 754 N |
| Moving mass | 365 g |
| Moving mass for 0 mm stroke | 205 g |
| Additional moving mass per 10 mm stroke | 16 g |
| Product weight | 1110 g |
| Basic weight for 0 mm stroke | 740 g |
| Additional weight per 10 mm stroke | 37 g |
| Type of mounting | Either: |
| Pneumatic connection | G1/4 |
| Note on materials | RoHS compliant |
| Material cover | Coated die-cast aluminium |
| Material piston seal | TPE-U(PU) |
| Material piston | Wrought aluminium alloy |
| Material piston rod | High-alloy steel |
| Material piston rod wiper | TPE-U(PU) |
| Buffer seal material | TPE-U(PU) |
| Material of cushioning boss | POM |
| Material cylinder barrel | Smooth-anodised wrought aluminium alloy |
| Material nut | Galvanised steel |
| Material bearing | POM |
| Material collar screws | Galvanised steel |
Working principle and cushioning of the DSBC-40-100-PPSA-N3
Compressed air admitted to one side of the piston pushes it while the opposite chamber exhausts; reversing the supply reverses the movement. Because the effective piston area on the rod side is smaller, the DSBC-40-100-PPSA-N3 produces 754 N advancing but 633 N on return at 6 bar, a difference of roughly 16 percent that matters for pulling loads. The cushioning is self-adjusting: the pneumatic cushion builds pressure in the last millimetres of travel and adapts to the moved energy, so no cushioning screws are present to set; the datasheet gives an impact energy of 0.7 J in the end positions and a cushioning length of 19 mm. A magnet on the piston allows the position to be read by proximity switches mounted on the barrel, so end positions can be monitored without any change to the cylinder.
Mass, weight and force data for sizing the DSBC-40-100-PPSA-N3
The moving mass is 205 g for 0 mm stroke plus 16 g per additional 10 mm, giving about 365 g at 100 mm; the product weight is 740 g plus 37 g per 10 mm, about 1110 g at 100 mm. These figures help to check carrying structures, to estimate the kinetic energy at the end of the stroke and to confirm that a mounting bracket is rated for the cylinder. Remember that the quoted forces are theoretical values at 6 bar; friction and seal drag reduce them in practice, so a safety margin is normal in sizing. The permitted operating pressure range is 0.6 bar to 12 bar, with an ambient temperature range of -20 °C to 80 °C.
Where the DSBC-40-100-PPSA-N3 fits: related Festo parts
The Festo DSBC datasheets we reviewed cover bores from 32 to 100 mm with standard strokes from 25 to 500 mm and two cushioning styles, PPVA with adjustable and PPSA with self-adjusting cushioning. Sibling codes include DSBC-40-100-PPVA-N3, DSBC-63-100-PPVA-N3, DSBC-100-100-PPVA-N3, DSBC-40-100-PPSA-N3, DSBC-63-100-PPSA-N3 and DSBC-40-200-PPVA-N3. Around the DSBC-40-100-PPSA-N3 you typically need foot, flange or clevis mountings, rod-end couplers, magnetic proximity switches, push-in fittings for the G1/4 port and a pressure regulator with filter. Send us the complete bill of materials if you want these items quoted together.
| Part number | Bore | Stroke | Advance force at 6 bar | Cushioning | Port |
|---|---|---|---|---|---|
| DSBC-40-100-PPVA-N3 | 40 mm | 100 mm | 754 N | Pneumatic cushioning, adjustable at both ends | G1/4 |
| DSBC-63-100-PPVA-N3 | 63 mm | 100 mm | 1870 N | Pneumatic cushioning, adjustable at both ends | G3/8 |
| DSBC-100-100-PPVA-N3 | 100 mm | 100 mm | 4712 N | Pneumatic cushioning, adjustable at both ends | G1/2 |
| DSBC-40-100-PPSA-N3 | 40 mm | 100 mm | 754 N | Self-adjusting pneumatic end-position cushioning | G1/4 |
| DSBC-63-100-PPSA-N3 | 63 mm | 100 mm | 1870 N | Self-adjusting pneumatic end-position cushioning | G3/8 |
| DSBC-40-200-PPVA-N3 | 40 mm | 200 mm | 754 N | Pneumatic cushioning, adjustable at both ends | G1/4 |
Selection and ordering checklist for DSBC-40-100-PPSA-N3
Choose the PPSA code over PPVA when you want the end-position cushioning to adapt by itself and do not want to set cushioning screws during commissioning.
- Bore and force: confirm that 754 N advance and 633 N return at your operating pressure, after friction losses, cover the load with margin.
- Stroke: 100 mm is fixed in this code; a different stroke is a different part number.
- Rod end: male thread with M12x1.25 thread; check that your coupler or clevis matches.
- Cushioning: self-adjusting pneumatic end-position cushioning; confirm this matches the moved mass and speed.
- Sensing: magnetic proximity switches can be fitted; confirm sensor type separately.
- Connection: G1/4 on both end covers; confirm the fittings and tube size.
- Environment: ambient range -20 °C to 80 °C; avoid aggressive media and welding spatter on the rod.
Installation, commissioning and maintenance of the DSBC-40-100-PPSA-N3
Mount the cylinder so that the load is guided and the rod sees axial force only; side loads on the rod bearing are the most common cause of early wear. Supply clean, dry compressed air at the quality stated in the datasheet (ISO 8573-1 class [7:4:4]) and fit a filter-regulator upstream. No cushioning screws need adjustment; run a few test cycles at low pressure and raise it step by step while watching the end positions. The datasheet notes that lubricated operation is possible but, once started, must be continued, so decide on lubrication at commissioning and keep to it. Inspect the wiper and piston rod surface during scheduled shutdowns, and keep spare seals or a complete spare cylinder for critical lines.
Typical applications of the DSBC-40-100-PPSA-N3 in Oman and the GCC
The self-adjusting cushioning version suits machines where the moved mass or speed changes often, for example multi-product packaging or palletising lines, because nobody has to open the cushioning screws after a format change. It is also popular where service access to the cylinder ends is poor. Plants in Oman and the wider GCC add extra demands: ambient heat, dust, humidity near the coast and long maintenance intervals. Check the temperature range in the table above, protect the rod from sand and abrasive dust with a bellows where needed, and ensure the compressed air is well dried so that moisture does not reach the cylinder.
Information to send with an RFQ for DSBC-40-100-PPSA-N3
- Full type code: DSBC-40-100-PPSA-N3 (and Festo part number 1376907 if known).
- Quantity and required delivery timeframe.
- Machine or plant where the part will be fitted, and whether it is a replacement or a new design.
- Nameplate photo of the existing cylinder if it is a replacement.
- Mounting accessories, proximity switches and fittings required alongside.
- Delivery destination in Oman or the GCC.
Documents and quotation
A datasheet for the DSBC-40-100-PPSA-N3 is attached on this page for reference. It lists the technical data shown above; check any application-specific limit against the document before committing to a design.
To request a quotation, send the part number DSBC-40-100-PPSA-N3, the quantity and the delivery location. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer.
Other Models in the Festo Dsbc Range
Seven Star LLC supplies models from the Festo Dsbc range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Festo DSBC-40-100-PPVA-N3 ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DSBC-63-100-PPVA-N3 ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DSBC-100-100-PPVA-N3 ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DSBC-40-100-PPSA-N3 ISO 15552 Cylinder | Automation Accessories | You are viewing this model |
Datasheets & Documents
- Datasheet Festo DSBC-40-100-PPSA-N3 Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Festo is a German maker of pneumatic and electric automation technology, founded in 1925 in Esslingen am Neckar by Albert Fezer and Gottlieb Stoll; the name comes from their surnames. It first made woodworking machines and power tools before moving into pneumatics in the 1950s. Festo is family-owned and still headquartered in Esslingen.
Seven Star LLC sources and supplies Festo cylinders, valves and valve terminals for machine maintenance and projects in Oman and the GCC.
Festo company profile
| Founded | 1925, Esslingen am Neckar, Germany |
|---|---|
| Founders | Albert Fezer and Gottlieb Stoll |
| Name | From FEzer and STOll |
| Headquarters | Esslingen am Neckar |
| Ownership | Family-owned |
| Product families | DSBC and ADN pneumatic cylinders, VUVG and VTUG solenoid valves and valve terminals, MS series air preparation units, CPX-AP remote I/O, EMMT servo motors and CMMT servo drives, electric axes and grippers |
Milestones
- 1925: Fezer and Stoll found the company in Esslingen.
- 1950s: Festo begins making pneumatic components.
Festo products listed
Two items show the two halves of a pneumatic circuit. The VTUG is a valve terminal: a manifold that carries a row of directional valves with common air supply and a shared electrical connection. The DSBC-32-100-PPVA-N3 is an ISO standard cylinder. Its type code reads as 32 mm piston diameter and 100 mm stroke, with adjustable end-position cushioning and a piston magnet for position sensing.
Festo products we list
Ordering Festo parts: what we need
Festo parts carry both a type code and a numeric part number on the label. Send both when you can; the part number is the shortest route to an exact match. For a cylinder give the full type code as on the listed DSBC example, plus mounting parts and proximity switches if required. For a VTUG valve terminal send the configuration code or a label photo: number of valve positions, valve functions, coil voltage and the electrical connection type all vary from one terminal to the next.
Facts checked against Festo's corporate history pages, October 2026.
Browse Festo products by category: Solenoid Valve, Valve Actuator.
FAQ
Questions about the Festo DSBC-40-100-PPSA-N3 ISO 15552 Cylinder
Answers from our engineering team on installation, compatibility and integration.
01What force does the DSBC-40-100-PPSA-N3 produce?
At 6 bar the datasheet gives a theoretical 754 N on the advance stroke and 633 N on the return stroke. Real forces are lower because of friction, so keep a safety margin when sizing the load.
02What are the operating pressure and temperature limits of the DSBC-40-100-PPSA-N3?
The operating pressure range is 0.6 bar to 12 bar and the ambient temperature range is -20 deg C to 80 deg C. Operation outside these limits is not covered by the datasheet.
03How is the end position of the DSBC-40-100-PPSA-N3 cushioned?
The datasheet lists: Self-adjusting pneumatic end-position cushioning. The permitted impact energy in the end positions is 0.7 J, which limits the moved mass and speed without an external damper.
04Can proximity switches be fitted to the DSBC-40-100-PPSA-N3?
Yes. The datasheet lists position detection via proximity switch, so magnetic switches can be mounted on the barrel. The switches themselves are separate items.
05What port and rod thread does the DSBC-40-100-PPSA-N3 have?
The pneumatic connection is G1/4 and the piston rod end is a male thread with M12x1.25 thread, per the datasheet. Confirm these against your fittings and couplers before ordering.


















Reviews
There are no reviews yet.