Brand:

Omron E2E-X14MD1 M18 2-Wire Proximity Sensor

Description

E2E-X14MD1 2M two-wire proximity sensor: what the code means

The Omron E2E-X14MD1 2M is a M18 unshielded DC 2-wire inductive proximity sensor with 14 mm sensing distance and normally open operation. An unshielded M18 body with 14 mm range gives generous clearance for heavy machinery, in a 2-wire connection. Seven Star LLC supplies the E2E-X14MD1 2M in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.

  • E2E is the standard inductive proximity family.
  • X14MD1 is the nominal range of 14 mm in a M18 body.
  • M marks unshielded (non-flush) construction.
  • D means DC 2-wire, in series with the load.
  • 1 means normally open, with a red operation and green setting indicator.
  • 2M is the 2 m pre-wired PVC cable version.

It is the longer-reaching 2-wire sibling of the E2E-X8MD1, with a bigger M18 barrel and 14 mm range, and it is a good fit where the target position varies.

E2E-X14MD1 2M technical specifications

Parameter Specification
Manufacturer / part number Omron / E2E-X14MD1 2M
Type Inductive proximity sensor, DC 2-wire, unshielded
Body size M18
Sensing distance 14 mm ±10%
Set distance 0 to 11.2 mm
Detectable object Ferrous metal
Supply voltage 12 to 24 VDC (operating range 10 to 30 VDC), ripple 10% max.
Leakage current 0.8 mA max.
Load current 3 to 100 mA
Residual voltage 3 V max. at 100 mA load with 2 m cable
Indicators Operation indicator (red) and setting indicator (green)
Operation mode Normally open
Protection Surge suppressor, load short-circuit protection
Ambient temperature Operating −25 to 70°C, storage −40 to 85°C, no icing or condensation
Humidity 35% to 95%, no condensation
Degree of protection IEC 60529 IP67, oil-resistant for pre-wired models
Connection Pre-wired, standard cable length 2 m
Weight (packed, pre-wired) Approx. 130 g

Values are from the manufacturer E2E-X datasheet. Check the datasheet for your final design.

How a 2-wire sensor like the E2E-X14MD1 operates

A DC 2-wire sensor sits in series with the load, so the same two conductors carry both its own operating current and the load current. When the sensor is off it still passes a small leakage current, 0.8 mA maximum for the E2E-X14MD1 2M, and when it is on it drops a residual voltage, 3 V maximum at 100 mA. The input device must therefore turn off at 0.8 mA and accept the reduced voltage.

The sensing part is the same oscillator-and-coil principle as in 3-wire models. Ferrous metal in the field damps the oscillation and the output switches. The green setting indicator lights when the target is inside the stable sensing zone and the red indicator shows output state, which helps commissioning.

Because it has no third wire, the sensor can replace a mechanical switch directly on existing two-core cable, which is one of the main reasons for choosing this type.

Where the E2E-X14MD1 2M fits and related part numbers

The 2-wire DC range of the series covers M8 to M30 in shielded and unshielded forms. Neighbours of the E2E-X14MD1 2M include E2E-X8MD1 (M12, 8 mm), E2E-X10ME1 (3-wire M18, 10 mm), E2E-X7D1 (shielded M18 2-wire).

Typical interface companions are PLC digital input cards with low off-state current thresholds, relay interface modules and counters. Always compare the leakage current of the sensor with the input off-threshold, otherwise the input may stay on even when the sensor is off. The datasheet also lists a model with a self-diagnostic output and connector versions; send the exact code if you need those.

Selection and ordering checklist for E2E-X14MD1 2M

  • Confirm the target is ferrous and that the gap stays inside the 0 to 11.2 mm set distance.
  • Check the input card tolerates 0.8 mA leakage and 3 V residual drop.
  • Check that supply is 10 to 30 VDC.
  • Allow free space around the unshielded M18 head.
  • Check load current is between 3 and 100 mA.
  • Choose 2 m pre-wired unless a connector model is needed.

Installation, commissioning and maintenance of the E2E-X14MD1 2M

Fit the sensor in a bracket with the supplied nuts, keeping other metal away from the face because it is unshielded. Wire the two conductors in series with the load and check polarity per the datasheet connection diagram.

During commissioning, bring the target to the closest position and check that the red indicator turns on; use the green setting indicator to verify the target is inside the stable zone. Verify that the load fully releases when the target moves away, which confirms the input is compatible with the leakage current.

For maintenance, inspect the cable, clean the face, and check nuts on vibrating equipment. Keep one spare of the same code on site for quick replacement.

Typical applications in Oman and the GCC

In Oman and the GCC, 2-wire sensors are often used in refurbishment work where existing field cables are two-core, such as on older conveyors, pump houses and compressor skids. The E2E-X14MD1 2M gives longer reach than 3-wire sensors of the same barrel size, which helps with the loose mounting tolerances typical of retrofit jobs. It is rated IP67 and oil-resistant when pre-wired, which suits dusty, hot and oily plants.

  • Large-gap position detection on slow mechanical equipment.
  • Long-throw detection of steel plates and frames approaching a stop.
  • Replacement of mechanical limit switches where a non-contact solution is preferred.

E2E-X 2-wire family comparison

Model Size Sensing distance Construction
E2E-X8MD1 M12 8 mm Unshielded
E2E-X14MD1 M18 14 mm Unshielded
E2E-X3D1 M12 3 mm Shielded
E2E-X7D1 M18 7 mm Shielded

The E2E-X14MD1 2M row shows how it compares with shielded and unshielded siblings for the same body size.

Information to send with an RFQ for E2E-X14MD1 2M

  • Full part number E2E-X14MD1 2M and quantity.
  • Input card model so leakage and residual voltage can be checked.
  • Target material and required gap.
  • Cable length or connector preference.
  • Supply voltage and temperature.
  • Datasheet requirements.

Documents and quotation

The manufacturer datasheet for the E2E-X series is attached on this page with dimensions and wiring details relevant to E2E-X14MD1 2M.

Send the part number, quantity and delivery point and Seven Star LLC will confirm availability. We are an independent supplier, not affiliated with the manufacturer.

Other Models in the Omron E2e X 2wire Range

Seven Star LLC supplies models from the Omron E2e X 2wire range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Omron E2E-X8MD1 M12 2-Wire Proximity SensorInductive Proximity SensorsView details
Omron E2E-X14MD1 M18 2-Wire Proximity SensorInductive Proximity SensorsYou are viewing this model
Datasheets & Documents
  • PDF Datasheet Omron E2E-X14MD1 2M Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Omron is a Japanese electronics and automation company, founded in 1933 in Osaka by Kazuma Tateisi and now headquartered in Kyoto. Its industrial automation business makes PLCs, I/O, sensors, relays, safety components, motion control and robots. Omron's CJ and NX series controllers and I/O units are widely used in machine building.

Seven Star LLC lists Omron PLC input and output units from the CJ and NX series and supplies them to panel builders and maintenance teams in Oman.

Omron company profile

Founded 1933, Osaka, Japan
Founder Kazuma Tateisi
Headquarters Kyoto, Japan
Business Industrial automation, healthcare, electronic components
Product families CJ1/CJ2 PLCs and I/O units, NX and NJ controllers, NX I/O, E2E proximity sensors, G2R and MY relays

Omron CJ-series and NX-series units listed here

Three I/O units are on this page. The CJ1W-ID211 is a CJ-series 16-point 24 VDC input unit and the CJ1W-OC211 is a CJ-series 16-point relay output unit. The NX-ID5442 is an NX-series 16-point 24 VDC digital input unit for PNP wiring, 12 mm wide with push-in terminals. CJ and NX units belong to different hardware platforms and do not plug into each other's racks.

Omron products we list

Family Examples
PLC & I/O Cards CJ1W-ID211 CJ-Series 16-Point 24 VDC Inp…, CJ1W-OC211 CJ-Series 16-Point Relay Outp…, NX-ID5442 NX-Series 16-Point Digital Inp…

Ordering Omron PLC modules: what we need

Send the complete model number from the front or side label of the unit, including every suffix. If you are replacing a failed card, add the CPU or coupler model it is mounted with, and tell us if the terminal block or connector is needed as well. For obsolete Omron PLC parts we check which successor the manufacturer documents. Requests from other GCC countries are handled the same way.

Facts checked against Omron's published company history, October 2026.

FAQ

Questions about the Omron E2E-X14MD1 M18 2-Wire Proximity Sensor

Answers from our engineering team on installation, compatibility and integration.

01What is the sensing distance of the E2E-X14MD1 2M?
The rated sensing distance is 14 mm ±10% on the standard ferrous object, with a set distance of 0 to 11.2 mm. It is an unshielded sensor, so keep the area around the face free of other metal.
02Is the E2E-X14MD1 2M a 2-wire or 3-wire sensor?
It is a DC 2-wire sensor, connected in series with the load. That keeps wiring simple, but the input has to tolerate the 0.8 mA maximum leakage current and a residual voltage of up to 3 V.
03What supply voltage does the E2E-X14MD1 2M need?
The rated supply is 12 to 24 VDC with an operating range of 10 to 30 VDC and 10% maximum ripple. The load current must stay between 3 mA and 100 mA.
04Does the E2E-X14MD1 2M have status indicators?
Yes. The D1 type has a red operation indicator and a green setting indicator. The green LED shows that the target is within the stable sensing range, which makes alignment checks simple.
05Can the E2E-X14MD1 2M be used outdoors in hot climates?
The rated operating range is −25 to 70°C with IP67 protection and oil-resistant pre-wired construction. For direct sun on a metal skid, check the surface temperature against the 70°C limit and shade the sensor if needed.