- Automation & ControlView all 2,679 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Motor Soft Starters
- Safety Switches & Guard Locking
- CCTV & Security
- Encoders
- HMI Displays
- Servo Drives
- Pneumatic Cylinders
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: MTL (Eaton)
MTL MTL4016 Switch/Proximity Detector Interface, 2-Channel
Description
MTL4016 overview
The MTL4016 is a two-channel switch and proximity detector interface unit with dual relay outputs. It allows two switches or proximity detectors located in a hazardous area to each control two safe-area loads, giving four reed-relay outputs in total. The unit is designed for applications where the status of one sensor must be sent to two separate systems, for example a control system and a shutdown system, with the electrical separation that relay contacts provide.
The MTL4016 includes independent phase-reversal switches for each channel, located on top of the module, so that an alarm can be signalled for either state of the sensor. Line fault detection monitors for broken or shorted field wiring, and facilities for earth-fault detection are provided through an optional link to an MTL4220 earth-leakage detector. Power and switch status are shown by LEDs on top of the module. The MTL4016 belongs to the backplane-mounting MTL4000 family that preceded the MTL4500 range.
Key features of the MTL MTL4016
- Two channels, each with two reed-relay outputs (1A/1B and 2A/2B)
- Suitable for switches in Zone 0 (IIC, T6) and NAMUR proximity detectors in Zone 0 (IIC, T4 to T6 if suitably certified)
- Sensor energised with 7.0 to 9.0 V dc from 1 kilohm; outputs close above 2.1 mA and open below 1.2 mA
- Built-in line fault detection that opens the outputs below 100 microamperes (broken line) or above 6.5 mA (shorted line)
- Independent phase-reversal switch for each channel on top of the module
- No-fail earth-fault protection when terminals 3 and 6 are linked to an MTL4220 earth-leakage detector
- 250 V ac isolation between safe-area and hazardous-area circuits
- Amber LED per channel and a green power LED; relays respond within 2 ms
MTL4016 technical specifications
The table lists data from the MTL4016 datasheet. Check the certification marking on the module you receive.
| Parameter | Value |
|---|---|
| Model | MTL4016 switch/proximity detector interface unit, two-channel, dual relay output |
| Channels | Two |
| Switch location | Zone 0, IIC, T6; Div. 1, Group A |
| Proximity detector location | Zone 0, IIC, T4-6 if suitably certified; Div. 1, Group A |
| Voltage applied to sensor | 7.0 to 9.0 V dc from 1 kohm |
| Output switching thresholds | Closed above 2.1 mA (below 2 kohm); open below 1.2 mA (above 10 kohm) |
| Hysteresis | 200 microamperes (650 ohm) nominal |
| Line fault detection | Outputs open if input current below 100 microamperes or above 6.5 mA |
| Relay outputs | Reed relays, double-pole on/off, open when de-energised |
| Contact rating | 10 W, 0.5 A, 35 V dc |
| Contact life | 10 to the power 6 operations at maximum load |
| Response time | 2 ms maximum |
| Isolation | 250 V ac between safe-area and hazardous-area circuits |
| Safety description per channel | 10.5 V, 800 ohm, 14 mA |
| FM entity parameters | Voc 10.5 V, Isc 14 mA, Ca 2.4 microfarad, La 165 mH |
| Power requirement | 50 mA at 24 V dc; 60 mA at 20 V; 45 mA at 35 V |
| Power dissipation | 1.2 W at 24 V; 1.6 W at 35 V |
| Indicators | Amber LED per channel (output closed); green LED power |
| Terminals | 1-2 input 1, 4-5 input 2, 3 and 6 optional earth-fault links, 7-8 and 8-9 outputs 1A and 2A, 10-11 and 11-12 outputs 1B and 2B, 13 supply -ve, 14 supply +ve |
The datasheet notes that switch-type sensors must be fitted with the resistors shown in its diagram, or line fault detection disabled with the switches on top of the unit, to avoid false triggering. Reactive loads on the relay contacts must be adequately suppressed. To maintain isolation between the two channels, separate earth-leakage detectors are needed.
Typical applications in oil and gas, utilities, water and manufacturing
The MTL4016 is used for digital field signals in hazardous areas: limit switches on valves, level switches in tanks, flow switches, and NAMUR inductive proximity sensors on rotating equipment. In Oman’s oil and gas plants, the two output contacts per channel let the same switch signal go to both the process control system and the emergency shutdown system, a common requirement for safety loops.
In power and water facilities across the GCC, the MTL4016 is applied to pump-status sensors, tank-level alarms and valve-position switches in classified areas such as fuel and biogas handling. Line fault detection is valuable on long field cables, because a broken or shorted wire is reported rather than being mistaken for a normal process state.
Selection and compatibility notes for MTL4016
Make sure the sensor is a switch or a NAMUR-type proximity detector compatible with the 7 to 9 V open-circuit supply and the threshold values of 2.1 mA and 1.2 mA. For switch contacts, fit the line-fault resistors per the datasheet. Compare the MTL4016 safety description of 10.5 V, 800 ohm and 14 mA with the entity parameters of the field device and cable.
Check the safe-area load: the reed contacts are rated for 10 W, 0.5 A and 35 V dc, so higher loads need an interposing relay. The MTL4016 is a backplane-mounted module from the MTL4000 family, so confirm that your existing backplane or cabinet system accepts it, and consider the MTL4500 and MTL5500 ranges for new designs.
Installation and commissioning
Before mounting the MTL4016, confirm the hazardous-area apparatus and the cable parameters against the entity values on the nameplate and in the manufacturer certificate, and decide where the intrinsic safety earth will be taken. Mount the unit on the 35 mm top-hat DIN rail in a clean enclosure or cabinet in the safe area, keeping hazardous-area and safe-area wiring physically separated and clearly labelled. As an MTL4000-family module, the MTL4016 plugs into its backplane, which provides the supply and safe-area connections; make sure the backplane is configured as the manufacturer’s installation documents require.
Wire the MTL4016 strictly to the terminal table in the datasheet, tighten the terminal screws to the specified torque and check that no strands are left outside the clamp. Where the unit carries a certificate, the earth connection and the rail must meet the requirements stated there. After wiring, apply the supply, check the power indication, and simulate the field signal to prove the end-to-end loop before the plant is declared ready. Record the as-found readings for future loop checks of the MTL4016.
Set the phase-reversal and line-fault-detection switches on top of the MTL4016 before the loop is put into service, and record the switch positions in the loop documentation. Test each channel by operating the field switch and observing the amber LED and the relay outputs.
Maintenance and service life
The MTL4016 has no user-serviceable parts, so maintenance is mainly periodic inspection. During planned shutdowns, inspect terminals for corrosion and looseness, verify the supply voltage at the unit, and repeat the loop check recorded at commissioning. In coastal or humid locations around Muscat, Sohar and Duqm, a sealed or purged cabinet with a clean, dry interior greatly extends the life of any electronic interface such as the MTL4016.
If a loop drifts outside its tolerance or the unit shows no power indication with a healthy supply, replace the module rather than attempting repair, and keep the replacement documentation with the loop folder. Because certified intrinsically safe equipment must not be modified, any change in cabling, load or hazardous-area device should be re-assessed against the MTL4016 entity parameters before it is put into service.
Related products and ordering notes
Customers who enquire about the MTL4016 often also need matching accessories and neighbouring models from the same family, such as the MTL4220 earth-leakage detector, other MTL4000 and MTL4500 interface modules and the corresponding DIN-rail MTL5000 and MTL5500 models. Please state whether you are replacing an installed MTL4016 or specifying a new system.
When you send an enquiry for the MTL4016, please quote the full part number exactly as printed on the nameplate, the quantity, and the intended application. If you are replacing an installed unit, a photograph of the nameplate helps us confirm the MTL4016 you need. Our team can arrange a quotation with delivery to Oman and across the GCC.
Frequently asked questions about MTL4016
The MTL4016 is a two-channel switch and proximity detector interface with four reed-relay outputs, line fault detection, phase-reversal switches and 250 V isolation. Its safety description is 10.5 V, 800 ohm and 14 mA, and it needs 24 V dc at about 50 mA.
Documents and quotation
A copy of the datasheet for the MTL4016 is available on this page for your engineering review. To request a quotation, send the RFQ with the part number MTL4016, the quantity, the delivery location and any certification or documentation requirements, and we will respond with availability and lead time. Please review the specification against your loop or system requirements before ordering.
Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with MTL. Product names and part numbers are used only to identify the item you ask for.
Datasheets & Documents
- Datasheet MTL4016 Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
MTL is a British maker of intrinsic safety interfaces, surge protection and hazardous-area equipment, founded in 1971 in Luton as Measurement Technology Ltd, a spin-off from Kent Instrumentation. In 2008 Cooper Industries bought MTL Instruments for £144 million and placed it in its Crouse-Hinds division; Eaton acquired Cooper in 2012. MTL is now part of Eaton's Crouse-Hinds business, alongside the MEDC signalling range.
Seven Star LLC lists MTL isolators, a fieldbus barrier and the configuration tools for them, and supplies MTL (Eaton) barriers and spare modules to sites in Oman as an independent supplier.
MTL (Eaton) company profile
| Founded | 1971, Luton, England, as Measurement Technology Ltd |
|---|---|
| Origin | Spin-off from Kent Instrumentation |
| Headquarters | Luton, England |
| Ownership | Eaton (Crouse-Hinds), via Cooper Industries from 2008 |
| Product families | MTL5500 and MTL4500 isolators, MTL7700 zener barriers, 9300 fieldbus barriers, surge protection devices, process junction boxes, PCS45 configuration software; MEDC beacons, sounders and call points |
Milestones
- 1971: Measurement Technology Ltd is founded in Luton.
- 2007: MTL acquires ELPRO Technologies, RTK Instruments and Ocean Technical Systems.
- 2008: Cooper Industries acquires MTL Instruments for £144 million.
- 2012: Eaton acquires Cooper Industries.
MTL product families listed here
Most of the listed items are DIN-rail galvanic isolators. The MTL5541 repeater power supply and the MTL5576-THC temperature converter belong to the MTL5500 range, and the MTL 5043 repeater power supply comes from the earlier MTL5000 range that many plants still run. The MTL 9370-FB2 is a fieldbus barrier for intrinsically safe FOUNDATION fieldbus spurs. PCS45 software with the PCL45USB link is the configurator for MTL converter modules. For the listed part CPM08-BN, please send a label photo so the number can be matched to the manufacturer's records. Newer labels show Eaton MTL, older ones Measurement Technology Ltd, and the module numbers are the same. The MTL 9608 is a fieldbus junction box with eight spur outlets plus a trunk-in connection, listed under the Crouse-Hinds series part number FCS-9608.
Where MTL barriers and isolators are used
These interfaces sit in marshalling cabinets wherever instruments are located in Zone 0, 1 or 2 areas: gas plants, refineries, offshore platforms, tank farms and chemical units across the GCC. They power 2-wire transmitters, pass HART, convert thermocouple signals and drive solenoids or alarms while limiting energy to the field circuit.
MTL (Eaton) products we list
Ordering MTL modules: what we need
Send the full module number including every suffix, for example MTL5576-THC and not just MTL5576, and the quantity. Tell us if the module mounts on DIN rail or on a backplane, because MTL5500 and MTL4500 parts are not interchangeable. For a fieldbus barrier give the number of spurs and the enclosure reference. A photo of the side label, which shows the certificate numbers, helps when the certificate for your project file must match.
Facts checked against the Eaton MTL company history and Drives & Controls coverage of the 2008 Cooper offer, October 2026.
Browse MTL (Eaton) products by category: Isolator & Barrier, Automation Software.
FAQ
Questions about the MTL MTL4016 Switch/Proximity Detector Interface,
Answers from our engineering team on installation, compatibility and integration.
01How many channels does the MTL4016 have?
The MTL4016 has two channels. Each channel can control two safe-area loads, which gives four reed-relay outputs in total.
02Does the MTL4016 have line fault detection?
Yes. Outputs open if the input current falls below 100 microamperes (broken line) or exceeds 6.5 mA (shorted line), and LFD can be disabled by switches on top of the unit.
03What are the relay contact ratings of the MTL4016?
The datasheet lists double-pole reed relays rated 10 W, 0.5 A and 35 V dc, with a 2 ms response time and 10 to the power 6 operations life at maximum load.
04What is the supply requirement of the MTL4016?
The datasheet gives 50 mA at 24 V dc, 60 mA at 20 V and 45 mA at 35 V, with 1.2 W dissipation at 24 V.
05How can I order the MTL4016?
Send an RFQ quoting MTL4016, the quantity and your delivery location in Oman or the GCC, and Seven Star LLC will respond with availability and lead time.


















Reviews
There are no reviews yet.