Brand:

ifm LMT110 Point Level Sensor, G 1/2 Sealing Cone, PEEK, IP69K

Description

ifm LMT110 Point Level Sensor, G 1/2 Sealing Cone, PEEK, IP69K

The ifm LMT110 is a point level sensor for liquid and viscous media and powder. It has a G 1/2 sealing cone thread, a stainless steel (316L) body with a PEEK sensing surface, a hygienic design for food and beverage and a surface finish of Ra below 0.8 micrometre. The medium temperature is -40 to 100 degrees Celsius and the tank pressure is -1 to 40 bar.

The outputs are switching and IO-Link, with a response below 0.5 s and a PNP/NPN selection, 100 mA. Protection is IP68 and IP69K. Seven Star LLC supplies the LMT110 in Oman and the GCC as an independent supplier in Muscat.

LMT110 technical specifications

The table lists the values published by the manufacturer for the LMT110. Where a parameter has several operating modes, the headline value is shown; the full parameter list is in the manufacturer documentation.

Parameter Specification
Manufacturer / part number ifm electronic / LMT110
Process connection threaded connection G 1/2 sealing cone
Dimensions [mm] Ø 30 / L = 113
Probe length [mm] 11
Media liquid and viscous media; powder
Medium temperature [°C] -40 to 100
Tank pressure -1 to 40 bar / -0.1 to 4 MPa
Operating voltage [V] 18 to 30 DC
Current consumption [mA] < 50
Output signal switching signal; IO-Link
Electrical design PNP/NPN
Output function normally open / normally closed (parameterisable)
Permanent current rating of switching output DC [mA] 100
Response time [s] < 0.5
Communication interface IO-Link
Ambient temperature [°C] -40 to 85
Protection IP 68; IP 69K
Weight [g] 210
Materials stainless steel (316L/1.4404); PEEK; PEI; FKM
Materials (wetted parts) PEEK surface characteristics: Ra < 0.8 µm / Rz = 4 µm
Connector 1 x M12; coding: A; Contacts: 4, gold-plated
MTTF [years] 223

How the LMT110 works

The LMT110 detects the presence of a medium at the probe tip with a capacitive principle: when liquid, paste or powder reaches the probe, the capacitance of the sensing electrode changes, and the electronics compare it with a stored reference for the selected medium type. The medium type is preset at the factory and can be changed through IO-Link, which tunes the sensing to the product. Because the stainless steel body and PEEK probe have no moving parts, the sensor is not affected by wear, sticking or mechanical float problems.

Where the LMT110 fits and related parts

The LMT110 is a sealing-cone type for hygienic tanks. The LMT100 and LMT121 in our range have other connections, and the LMC510 is a capacitive type.

Selection and ordering checklist for the LMT110

Work through the points below before you confirm the order, so that the LMT110 you receive is the one your machine or plant needs.

  • Confirm the G 1/2 sealing cone
  • Check the medium and deposits
  • Check the temperature range
  • Confirm the tank pressure
  • Choose switching or IO-Link

The manufacturer lists this article under the type designation Sensor for point level detection, LMACE-A12E/QSKG/1/US. The article number LMT110 is the reference to quote when ordering, and the type designation is useful for technicians who compare the label on an installed unit.

Installation, commissioning and maintenance

Install the sensor in a nozzle or tank wall so that the probe tip protrudes by the stated length into the product, keeping it away from internal structures and filling jets. Seal it with the correct cone or thread seal for the process connection and observe the allowed tank pressure and medium temperature. At commissioning, select the medium type, run the tank to the switching level and check the output, and then test with product that clings to the probe to see that the build-up is rejected. Inspect the probe from time to time for heavy deposits and keep the M12 connection tight and dry.

Typical applications in Oman and the GCC

Dairy, beverage and chemical tanks and process vessels. In Oman and the GCC it is used on water treatment, food and utility tanks.

Level sensors in tanks exposed to Gulf summers must tolerate hot product, condensation on cold nozzles and long periods without attention. Plan a periodic proof test of the alarm point, and record the output state at known levels during commissioning.

LMT110 compared with related ifm types

The table places the LMT110 next to neighbouring types in the same application group, so you can see whether a sibling would suit the job better.

Part number Key characteristics Note
LR3000 GWR, G 3/4, 100-1600 mm probe, 4-20 mA, IO-Link Related type
LMT110 Point level, G 1/2 cone, -40 to 100 C, 40 bar, IO-Link This page
LK3123 Continuous capacitive, 472 mm, 4-20 mA, IO-Link Related type
LMT100 Point level sensor Related type
LMC510 Capacitive point level sensor Related type
LK1022 Continuous level sensor Related type
LR2750 Guided wave radar Related type

Information to send with an RFQ for the LMT110

To prepare an accurate offer for the LMT110, please include the following with your enquiry:

  • Medium (water-based, oil, powder or paste) and its temperature
  • Tank pressure and cleaning method (CIP or washdown)
  • Process connection type and thread
  • Switching or IO-Link requirement
  • Quantity and delivery location

Storage, handling and spares for the ifm LMT110

Keep ifm LMT110 units in their original packaging until they are mounted. Store them indoors in a dry, dust-free room, away from direct sun and condensation. Panel shops in Oman and the GCC often hold stock in warehouses that get very hot in summer, so check that storage temperature stays within the limits given in the manufacturer datasheet.

  • Check the label and order code on every unit against the drawing before it goes into the panel.
  • Use the correct tool and tightening torque for the terminals, as given in the instructions supplied with the product.
  • Keep a small number of spare units for each rating used on site, so that a failed or damaged part can be replaced without waiting for a new shipment.
  • Record the order code in the panel documentation and the as-built drawings, so that maintenance teams can reorder the same part later.

When you plan spares for a project, group the ifm LMT110 with the other parts of the same panel in one RFQ. This keeps delivery dates aligned and makes it easier to confirm stock for the whole bill of materials at once.

Documents and quotation

The official ifm data sheet for the LMT110 (document LMT110-01, English, issued 13 April 2023) is attached on this page as a PDF. It sets out the electrical data, the output function, the operating conditions, the approvals and the dimension drawing for this article. Check these values and the wiring diagram against your application before ordering, then send us the quantity and the delivery location for a quotation.

Seven Star LLC is an independent supplier in Muscat serving Oman and the GCC and is not affiliated with the manufacturer; the name ifm is used only to identify the product. Prices are not shown on the page, so send the part number, the quantity and the delivery location to receive a quotation.

Other Models in the Ifm61 Level Range

Seven Star LLC supplies models from the Ifm61 Level range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
ifm LR3000 Guided Wave Radar Level Sensor, G 3/4, 100-1600 mmAutomation AccessoriesView details
ifm LMT110 Point Level Sensor, G 1/2 Sealing Cone, PEEK, IP69KAutomation AccessoriesYou are viewing this model
Datasheets & Documents
  • PDF Datasheet ifm LMT110 Data Sheet (PDF) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.

Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.

ifm company profile

Founded 1969, Essen, Germany
Founders Robert Buck and Gerd Marhofer
Headquarters Essen, Germany
Ownership Family-owned
Product families Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters

Milestones

  • 1969: ifm is founded in Essen.
  • 2001: The founders' sons take over management.

ifm sensors listed on this page

ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:

  • O1D100: laser distance sensor for position and distance measurement
  • PN7093: pressure sensor with local display
  • NG5021: inductive proximity sensor with NAMUR output

Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.

ifm products we list

Family Examples
Inductive Proximity Sensors NG5021 Inductive NAMUR Proximity Sensor
Laser Distance, LiDAR & Radar Sensors O1D100 Laser Distance Sensor
Pressure Instrumentation PN7093 Pressure Sensor with Display

Ordering ifm sensors: what we need

Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.

Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.

FAQ

Questions about the ifm LMT110 Point Level Sensor, G 1/2 Sealing Cone,

Answers from our engineering team on installation, compatibility and integration.

01What process connection does the ifm LMT110 have?
G 1/2 with a sealing cone. This is the value published by the manufacturer for the LMT110; confirm details before ordering.
02What media can the LMT110 detect?
Liquid and viscous media and powder. This is the value published by the manufacturer for the LMT110; confirm details before ordering.
03What temperature range applies to the LMT110?
-40 to 100 degrees Celsius medium. This is the value published by the manufacturer for the LMT110; confirm details before ordering.
04What protection does the LMT110 have?
IP68 and IP69K. This is the value published by the manufacturer for the LMT110; confirm details before ordering.
05Does the LMT110 support IO-Link?
Yes, with switching outputs. This is the value published by the manufacturer for the LMT110; confirm details before ordering.