Fluke 175 True-RMS Digital Multimeter, CAT III 1000 V

175 baseline true-RMS multimeter for industrial work explained

The Fluke 175 True-RMS Digital Multimeter (175) is the entry model of the Fluke 170 series. It carries the same ranges, safety category and rugged body as the 177 and 179, with a slightly relaxed DC voltage accuracy, which makes it an economical general-purpose instrument. Seven Star LLC supplies 175 in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.

The 175 is the reference point for the family, so the decoding below shows what is shared and what changes upward.

175 technical specifications

Figures come from the manufacturer product page for the Fluke 175 and are best accuracy for each function.

How the Fluke 175 True-RMS Digital Multimeter works

The 175 uses the same measurement engine layout as the rest of the series: input protection, range selection, true-RMS conversion and a 6000-count display. Because all inputs are protected to CAT IV 600 V and CAT III 1000 V, the same instrument can be used on a motor terminal box and on a distribution board without changing meters.

Display Hold and Auto Hold capture a stable value so you can record it later. The auto-hold function is useful when both hands are busy with probes and the display is hard to see; it latches when the reading settles and beeps to confirm.

Key features

• All inputs protected to CAT IV 600 V and CAT III 1000 V
• Display Hold and Auto Hold
• Ergonomic case with integrated holster
• Closed-case calibration through the front panel
• Frequency, capacitance, resistance, continuity and diode tests

Where 175 fits and related Fluke models

Choose the 175 when the job is general troubleshooting and a DC accuracy of 0.15% is more than enough, for example checking supplies and continuity. If you later need higher DC accuracy, the 177 is the next step, and the 179 adds temperature.

The 175 is also the family member most often kept in tool cribs, where many instruments are issued to different technicians and cost control matters.

Selection checklist for 175

Confirm the following points before ordering, so that the instrument matches the work and the safety rules of your site.

• DC accuracy needs: 0.15% is adequate for power circuits and most control wiring.
• Temperature and logging are not included.
• Direct current is limited to 10 A.
• Check how many leads and clips each technician needs.

Safe use, care and maintenance of 175

• Before each shift, inspect the case, the holster and the test leads. Cracked insulation, exposed metal or a loose input jack means the leads should be replaced before the 175 touches any live circuit.
• Confirm the meter on a known live source before and after a measurement that decides whether a circuit is dead. Never rely on a single reading when the result will be used to release a lock-out.
• Keep the input fuses to the specified type only. A blown fuse in the current inputs is the most common service event on a multimeter used on motor circuits, and a wrong fuse defeats the safety design of the Fluke 175 True-RMS Digital Multimeter.
• Replace the battery when the low-battery symbol appears, because readings near the lower end of the range become unreliable on a weak cell. Remove the battery before long storage.
• Store the instrument clean and dry. In coastal Oman, wipe off salt film and condensation after outdoor use and avoid leaving it in a vehicle cabin in summer.

Typical applications of 175 in Oman and the GCC

Handheld multimeters are carried in every plant. In Oman, oil and gas facilities, power stations, desalination plants and petrochemical sites rely on them for control-panel faults, motor circuits, instrument loops and routine electrical checks.

In industrial plants the 175 serves as a shared workshop meter and as the default instrument for apprentices and junior technicians. It copes with panel work, motor circuits and utility checks, and its rugged holster tolerates the knocks of shutdown work on Oman refinery, power and water sites.

175 compared with nearby models

Only the DC accuracy and the temperature input separate the three models; the other ranges are the same.

Information to send with an RFQ for 175

To prepare an accurate quotation, please send:

• Exact model 175 and the quantity required.
• Whether the meter is for a lab, a workshop or field service, so the correct accessory set can be quoted.
• Required test lead type and any extra clips or probes.
• Temperature probe, case or magnetic hanger requirements.
• Whether calibration traceability paperwork is needed on delivery.
• Delivery point in Oman or elsewhere in the GCC and the required date.

Documents and quotation

A manufacturer datasheet for the Fluke 175 True-RMS Digital Multimeter is attached on this page so that you can check the full specification before ordering. Please review it against your site requirements.

For a quotation, send the part number 175, the quantity and your delivery location in Oman or the GCC through the RFQ button on this page. Availability and lead time are confirmed per request.