Brand:

Pepperl+Fuchs NBN15-30GM50-E2 M30 PNP Inductive Sensor, 15 mm

Description

Pepperl+Fuchs NBN15-30GM50-E2 overview

The Pepperl+Fuchs NBN15-30GM50-E2 is a cylindrical M30 x 1.5 inductive sensor from the basic series of Pepperl+Fuchs with a rated operating distance of 15 mm and non-flush installation. It has a normally open PNP output in a 3-wire design, a nickel-plated brass housing, a PBT sensing face and a 2 m PVC cable.

The datasheet released on 20 March 2020 lists an operating voltage of 10 to 30 V DC, a switching frequency up to 200 Hz and an all-direction yellow LED for the switching state. The sensor is protected against reverse polarity and short circuit and has IP67 protection.

Key features of the Pepperl+Fuchs NBN15-30GM50-E2

  • M30 x 1.5 nickel-plated brass housing, PBT sensing face
  • Rated operating distance 15 mm, non-flush installation
  • Normally open PNP output, 3-wire design
  • Operating voltage 10 to 30 V DC, output current up to 200 mA
  • Switching frequency 0 to 200 Hz
  • All-direction yellow LED for switching state
  • Reverse polarity and pulsing short-circuit protection
  • IP67 protection, 2 m PVC cable

NBN15-30GM50-E2 technical specifications

The values below are taken from the manufacturer datasheet of the NBN15-30GM50-E2, release date 2020-03-20. Always confirm the current datasheet and the certificates before final engineering.

Parameter Value
Model NBN15-30GM50-E2, inductive sensor, basic series
Switching function / output Normally open (NO), PNP, 3-wire
Rated operating distance sn 15 mm
Assured operating distance sa 0 to 12.15 mm
Installation Non-flush
Operating voltage 10 to 30 V
Switching frequency / hysteresis 0 to 200 Hz / typically 5 percent
Voltage drop / operating current Up to 3 V / 0 to 200 mA
No-load supply current Up to 15 mA
Functional safety data MTTFd 1803 a; mission time 20 a; DC 0 percent
Ambient temperature Minus 25 to 70 degrees C
Housing / sensing face Nickel-plated brass / PBT
Protection IP67
Cable PVC, 4.6 mm diameter, 0.34 mm2, length 2 m
Thread M30 x 1.5

Values for supply, current and temperature apply to the conditions stated in the datasheet; verify them against your application, especially for cold or hot installations.

Typical applications in oil and gas, utilities, water and manufacturing

Three-wire PNP inductive sensors are the workhorse of position detection on machines, valves and conveyors in plants of every kind. The NBN15-30GM50-E2 is applied on valve actuator feedback, pump and compressor skids, gate and damper positions and similar duties in oil and gas, power, water and manufacturing sites in Oman and the GCC.

Because the output is a solid-state PNP switch, it connects straight to PLC digital inputs without a relay and tolerates the vibration and dirt of industrial environments. The sensor is not an intrinsically safe device, so use it in non-hazardous areas or follow the instructions and certificates for any hazardous use.

Selection and compatibility notes for NBN15-30GM50-E2

Check the supply voltage range, the switching frequency and the output current against your input card. The datasheet gives the voltage drop, the no-load current and the delay before availability, and these affect fast counting or sequential logic.

Check the sensing distance against the target material and the mounting. A non-flush sensor needs free space around the sensing face, and the reduction factors in the datasheet show how much the operating distance drops for non-ferrous metals.

Installation and commissioning of the NBN15-30GM50-E2

Before mounting the NBN15-30GM50-E2, check the free space around the sensing face, the mounting hole or bracket and the cable or connector route. Tighten the fixing nuts only to the torque recommended for the housing so that the thread and the sensing face are not damaged, keep cables away from power wiring where possible, and fit the sensor so that the target passes at a repeatable distance well inside the assured operating distance.

Connect the NBN15-30GM50-E2 according to the connection diagram of the datasheet, then move the target through the sensing zone and watch the switching state at the input of the amplifier or controller. Record the switching distance at commissioning, so that later checks can show whether the NBN15-30GM50-E2 has drifted or the target has moved.

Maintenance and service life

The NBN15-30GM50-E2 has no serviceable parts. During planned shutdowns, inspect the housing, the cable or connector and the mounting for damage, loosened nuts and build-up of metal chips or dirt on the sensing face, and repeat the switching distance check recorded at commissioning. In coastal and humid locations such as Muscat, Sohar and Duqm, check cable glands and connector seals for corrosion.

If the NBN15-30GM50-E2 stops switching or switches erratically, check the supply, the wiring and the target position before replacing it. Replace a damaged sensor instead of repairing it, and keep the replacement documentation in the loop folder. Certified equipment must not be modified, and any change of cable or amplifier should be re-assessed against the sensor data.

Related products and ordering notes

Customers who ask for the NBN15-30GM50-E2 often need neighbouring models or accessories from the same system, such as other NAMUR and PNP inductive sensors of neighbouring sizes, K-System switch amplifiers, mounting brackets and connector cables. If you are standardising a cabinet or a spare parts list on one family, send us the loop list or the equipment list and we can quote the matching items together.

When you send an enquiry for the NBN15-30GM50-E2, quote the full part number exactly as printed on the nameplate, the quantity and the intended application. If you are replacing an installed unit, a photograph of the nameplate helps us confirm the exact variant you need. We can arrange a quotation with delivery to Oman and across the GCC.

Frequently asked questions about NBN15-30GM50-E2

The NBN15-30GM50-E2 is an M30 non-flush PNP inductive sensor with 15 mm operating distance, normally open output, 10 to 30 V DC supply, 200 Hz switching frequency and a 2 m cable.

Documents and quotation

A copy of the manufacturer datasheet for the NBN15-30GM50-E2 is attached to this page for your engineering review. To request a quotation, send the RFQ with the part number NBN15-30GM50-E2, the quantity, the delivery location and any certification or documentation requirements, and we will reply with availability and lead time. Please check the specification against your loop or system requirements before ordering.

Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with Pepperl+Fuchs. Product names and part numbers are used only to identify the item you ask for.

Datasheets & Documents
  • PDF Datasheet NBN15-30GM50-E2 Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Pepperl+Fuchs is a German manufacturer of industrial sensors and explosion protection equipment, founded in 1945 in Mannheim by Walter Pepperl and Ludwig Fuchs as a radio repair shop. Defective transformers led them into manufacturing, and the company developed its first proximity switch in the late 1950s. Pepperl+Fuchs is headquartered in Mannheim and is a pioneer of intrinsically safe electrical equipment for hazardous areas.

Seven Star LLC lists Pepperl+Fuchs sensors, isolated barriers, power supplies and hazardous-area mobile devices, and supplies them to instrument and automation teams in Oman by exact model designation.

Pepperl+Fuchs company profile

Founded 1945, Mannheim-Sandhofen, Germany, by Walter Pepperl and Ludwig Fuchs
Headquarters Mannheim, Germany
Ownership Privately owned (Pepperl+Fuchs SE)
Origins Radio repair workshop that began making replacement transformers
Product families Inductive, capacitive, ultrasonic and photoelectric sensors, rotary encoders, R2000 LiDAR scanners, KFD and HiC isolated barriers, Zener barriers, remote I/O, purge and pressurization systems, Ex-rated enclosures

Milestones

  • 1945: Walter Pepperl and Ludwig Fuchs open their radio repair shop in Mannheim.
  • 1958: The first proximity switch is developed (some company sources say 1959).

Pepperl+Fuchs product families on this page

On the interface side there are two systems. The K-System mounts on DIN rail and is represented here by the KFD2-UT2-Ex2 universal temperature converter. The H-System plugs into termination boards and is represented by the HiD2030 SMART transmitter power supply with HART. The PS1000-A6-24.20 is a 24 VDC, 20 A power supply for cabinets. Sensors listed include the NJ2-12GK-SN NAMUR inductive sensor, the R101 retro-reflective photoelectric sensor and the R2000 2-D LiDAR scanner. For field staff there are the Tab-Ex 05 DZ1 tablet for Zone 1/21 areas and the Smart-Ex 03 DZ2 smartphone for Zone 2/22 and Division 2 areas.

Where Pepperl+Fuchs equipment is used

Isolated barriers sit between field instruments in Zone 0 or Zone 1 and the DCS or safety system in refineries, gas plants and chemical works. NAMUR sensors report valve position and machine states in classified areas. Photoelectric sensors and LiDAR scanners work in conveying, packaging, warehousing and vehicle guidance. Ex-rated tablets and phones are carried on operator rounds and maintenance jobs.

Pepperl+Fuchs products we list

Family Examples
Isolator & Barrier HiD2030 SMART Transmitter Power Supply w…, KFD2-SR2-Ex2.W K-System Isolated Switch…, KFD2-UT2-Ex2 Universal Temperature Conve…
Industrial Computers Tab-Ex 05 DZ1 WWAN Hazardous Area Tablet, Smart-Ex® 03 DZ2 smartphone for Zone 2/2…
Inductive Proximity Sensors NJ2-12GK-SN NAMUR Inductive Sensor
Power Modules PS1000-A6-24.20 Power Supply 24 VDC 20 A
Photoelectric Sensors R101 Retro-Reflective Photoelectric Sensor
Laser Distance, LiDAR & Radar Sensors R2000 2-D LiDAR Laser Scanner

Ordering Pepperl+Fuchs parts: what we need

Send the complete model designation as printed on the device, including every suffix; a single letter can change the supply voltage or the output type. Add the part number if the label shows one. For barriers, tell us the field device and signal type, the number of channels and whether the safety loop needs a SIL-assessed module. For mobile devices, state the zone or division and the regional radio version.

Facts checked against Pepperl+Fuchs's own chronicle pages, October 2026.

FAQ

Questions about the Pepperl+Fuchs NBN15-30GM50-E2 M30 PNP Inductive

Answers from our engineering team on installation, compatibility and integration.

01What is the operating distance of the NBN15-30GM50-E2?
The rated operating distance is 15 mm and the assured operating distance is 0 to 12.15 mm, with non-flush installation.
02What output does it have?
A normally open PNP output in a 3-wire design, switching up to 200 mA.
03What is its maximum switching frequency?
The datasheet gives a switching frequency range of 0 to 200 Hz for this sensor.
04Which documents are available for the NBN15-30GM50-E2?
The manufacturer datasheet is attached to this page, and certificates or manuals can be requested together with your RFQ for the NBN15-30GM50-E2.
05How do I order the NBN15-30GM50-E2?
Send an RFQ with the part number NBN15-30GM50-E2, the quantity and the delivery location in Oman or the GCC, and Seven Star LLC will reply with availability and lead time.