Brand:

ifm OGP500 Retro-Reflective Sensor M18, Stainless, Red Light

Description

ifm OGP500 Retro-Reflective Sensor M18, Stainless, Red Light

The ifm OGP500 is a retro-reflective photoelectric sensor in an M18 x 1 stainless steel housing, 72 mm long. It works with red light (624 nm), is set by pushbutton, and can be programmed as light-on or dark-on. The PNP output is rated for 150 mA, rising to 200 mA up to 60 degrees Celsius, and the switching frequency is 2000 Hz.

It runs from 10 to 36 V DC at 20 mA and handles ambient temperatures from -25 to 80 degrees Celsius with IP67 protection. Seven Star LLC supplies the OGP500 in Oman and the GCC as an independent supplier in Muscat.

OGP500 technical specifications

The table lists the values published by the manufacturer for the OGP500. Where a parameter has several operating modes, the headline value is shown; the full parameter list is in the manufacturer documentation.

Parameter Specification
Manufacturer / part number ifm electronic / OGP500
Function principle Retro-reflective sensor
Thread designation M18 x 1
Dimensions [mm] M18 x 1 / L = 72
Type of light red light
Wave length [nm] 624
Max. light spot diameter [mm] 200
Operating voltage [V] 10 to 36 DC
Current consumption [mA] 20
Electrical design PNP
Output function light-on/dark-on mode (programmable)
Permanent current rating of switching output DC [mA] 150 (200 ( to 60 °C))
Switching frequency DC [Hz] 2000
Ambient temperature [°C] -25 to 80
Protection IP 67
Weight [g] 52.1
Materials stainless steel (316L/1.4404); PA; LCP; EPDM; TPU
Connector 1 x M12; coding: A; Contacts: 4
MTTF [years] 431

How the OGP500 works

The OGP500 is a retro-reflective sensor in an M18 x 1 stainless steel tube. It transmits red light at 624 nm and expects it back from a reflector across the detection zone. When an object interrupts the beam the output changes, and the sensitivity is set with a pushbutton so the sensor accepts the return of the installed reflector while ignoring minor contamination. The light spot reaches 200 mm in diameter, which tolerates small alignment shifts. The metal tube makes it a good choice where plastic housings would be struck or scratched.

Where the OGP500 fits and related parts

Compared with the plastic rectangular O5P500, the OGP500 offers a metal tube, M18 mounting and a higher temperature limit. The OGH580 and O6H700 in our range are diffuse types that need no reflector.

Selection and ordering checklist for the OGP500

Work through the points below before you confirm the order, so that the OGP500 you receive is the one your machine or plant needs.

  • Confirm the M18 x 1 stainless housing is needed
  • Confirm the reflector distance
  • Check the derating of output current above 60 degrees Celsius
  • Choose light-on or dark-on
  • Check the supply and PNP input

The manufacturer lists this article under the type designation Retro-reflective sensor, OGP-FPKG/US100. The article number OGP500 is the reference to quote when ordering, and the type designation is useful for technicians who compare the label on an installed unit.

Installation, commissioning and maintenance

Thread the tube into a bracket or a hole and lock it with nuts, then align with the reflector. A reflector of suitable size, fixed on a stable surface, is as important as the sensor itself, and a fixed reflector that is cleaned at each shift keeps the reserve of light high. Press the pushbutton to set the sensitivity with the beam clear, and test with the smallest object. The housing allows 80 degrees Celsius ambient, but the output current is 150 mA at that limit and 200 mA up to 60 degrees Celsius, so size the load accordingly.

Typical applications in Oman and the GCC

Detection of containers and packages on conveyors, access gates and machine guards. In Oman and the GCC the stainless tube resists dust, sand abrasion and cleaning, and the 80 degrees Celsius limit helps near hot equipment.

Optical sensors on open conveyors and loading areas meet dust, sand and strong sunlight. Regular lens cleaning, a firm bracket and a check of the switching point after any mechanical change keep detection reliable.

OGP500 compared with related ifm types

The table places the OGP500 next to neighbouring types in the same application group, so you can see whether a sibling would suit the job better.

Part number Key characteristics Note
O5C500 Colour sensor, RGB LED, 15-19 mm, 2 kHz Related type
O5P500 Retro-reflective, red light, 250 mm spot, 2 kHz Related type
OGP500 M18 stainless, retro-reflective, 200 mm spot, 80 C This page
O8H200 Miniature, 3-15 mm, 4 mm spot, IO-Link Related type
O5D100 Compact distance sensor Related type
O6H700 Background suppression sensor Related type
OGH580 M18 stainless diffuse sensor Related type

Information to send with an RFQ for the OGP500

To prepare an accurate offer for the OGP500, please include the following with your enquiry:

  • Distance to the reflector
  • Object size and surface
  • Light-on or dark-on logic
  • Ambient temperature range
  • Reflector type and mounting bracket

Storage, handling and spares for the ifm OGP500

Keep ifm OGP500 units in their original packaging until they are mounted. Store them indoors in a dry, dust-free room, away from direct sun and condensation. Panel shops in Oman and the GCC often hold stock in warehouses that get very hot in summer, so check that storage temperature stays within the limits given in the manufacturer datasheet.

  • Check the label and order code on every unit against the drawing before it goes into the panel.
  • Use the correct tool and tightening torque for the terminals, as given in the instructions supplied with the product.
  • Keep a small number of spare units for each rating used on site, so that a failed or damaged part can be replaced without waiting for a new shipment.
  • Record the order code in the panel documentation and the as-built drawings, so that maintenance teams can reorder the same part later.

When you plan spares for a project, group the ifm OGP500 with the other parts of the same panel in one RFQ. This keeps delivery dates aligned and makes it easier to confirm stock for the whole bill of materials at once.

Documents and quotation

The official ifm data sheet for the OGP500 (document OGP500-00, English, issued 13 April 2023) is attached on this page as a PDF. It sets out the electrical data, the output function, the operating conditions, the approvals and the dimension drawing for this article. Check these values and the wiring diagram against your application before ordering, then send us the quantity and the delivery location for a quotation.

Seven Star LLC is an independent supplier in Muscat serving Oman and the GCC and is not affiliated with the manufacturer; the name ifm is used only to identify the product. Prices are not shown on the page, so send the part number, the quantity and the delivery location to receive a quotation.

Other Models in the Ifm61 Photo Range

Seven Star LLC supplies models from the Ifm61 Photo range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
ifm O5C500 Colour Sensor, RGB Light, Teach, 15-19 mmAutomation AccessoriesView details
ifm O5P500 Retro-Reflective Sensor, Red Light, Teach, PNPAutomation AccessoriesView details
ifm OGP500 Retro-Reflective Sensor M18, Stainless, Red LightAutomation AccessoriesYou are viewing this model
Datasheets & Documents
  • PDF Datasheet ifm OGP500 Data Sheet (PDF) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.

Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.

ifm company profile

Founded 1969, Essen, Germany
Founders Robert Buck and Gerd Marhofer
Headquarters Essen, Germany
Ownership Family-owned
Product families Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters

Milestones

  • 1969: ifm is founded in Essen.
  • 2001: The founders' sons take over management.

ifm sensors listed on this page

ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:

  • O1D100: laser distance sensor for position and distance measurement
  • PN7093: pressure sensor with local display
  • NG5021: inductive proximity sensor with NAMUR output

Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.

ifm products we list

Family Examples
Inductive Proximity Sensors NG5021 Inductive NAMUR Proximity Sensor
Laser Distance, LiDAR & Radar Sensors O1D100 Laser Distance Sensor
Pressure Instrumentation PN7093 Pressure Sensor with Display

Ordering ifm sensors: what we need

Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.

Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.

FAQ

Questions about the ifm OGP500 Retro-Reflective Sensor M18, Stainless,

Answers from our engineering team on installation, compatibility and integration.

01What housing does the ifm OGP500 have?
An M18 x 1 stainless steel tube, 72 mm long. This is the value published by the manufacturer for the OGP500; confirm details before ordering.
02What ambient temperature does the OGP500 allow?
-25 to 80 degrees Celsius. This is the value published by the manufacturer for the OGP500; confirm details before ordering.
03What is the light spot of the OGP500?
Up to 200 mm in diameter. This is the value published by the manufacturer for the OGP500; confirm details before ordering.
04How is the OGP500 adjusted?
By pushbutton for sensitivity, with light-on or dark-on programmable.
05What is the output current of the OGP500?
150 mA, and 200 mA up to 60 degrees Celsius. This is the value published by the manufacturer for the OGP500; confirm details before ordering.