- Automation & ControlView all 2,610 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Festo
Festo ADN-25-40-A-P-A Compact Cylinder
Description
ADN-25-40-A-P-A: Festo 25 mm bore, 40 mm stroke compact cylinder
The Festo Festo ADN-25-40-A-P-A (Festo part number 536257) is a double-acting compact cylinder with a 25 mm piston and a 40 mm stroke, built to ISO 21287. At 6 bar it develops a theoretical 295 N on the advance stroke and 247 N on the return stroke, uses elastic cushioning rings or plates at both ends, and has a male thread piston rod end with M8 thread. Seven Star LLC supplies the Festo ADN-25-40-A-P-A in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.
How to read the ADN-25-40-A-P-A type code
Every element of the type code carries a design decision. Reading it left to right avoids ordering the wrong sibling:
- ADN: Festo compact cylinder series
- 25: piston diameter 25 mm
- 40: stroke 40 mm
- A: piston rod end with male thread
- P: elastic cushioning rings or plates at both ends
- A: position sensing via proximity switch
The datasheet remains the reference. If a type code on a nameplate differs from the code in an enquiry, send us the nameplate photo and we will confirm before quoting.
Festo ADN-25-40-A-P-A technical specifications
| Parameter | Specification |
|---|---|
| Manufacturer / part number | Festo ADN-25-40-A-P-A (Festo part number 536257) |
| Product type | Compact cylinder |
| Stroke | 40 mm |
| Piston diameter | 25 mm |
| Piston rod thread | M8 |
| Cushioning | Elastic cushioning rings/plates at both ends |
| Mounting position | Any |
| Conforms to standard | ISO 21287 |
| Piston-rod end | Male thread |
| Position detection | Via proximity switch |
| Variants | Piston rod at one end |
| Operating pressure | 0.06 MPa to 1 MPa; 0.6 bar to 10 bar |
| Mode of operation | Double-acting |
| Operating medium | Compressed air to ISO 8573-1:2010 [7:4:4] |
| Note on operating and pilot medium | Lubricated operation possible (in which case lubricated operation will; always be required) |
| Corrosion resistance class CRC | 2 – Moderate corrosion stress |
| LABS (PWIS) conformity | VDMA24364-B1/B2-L |
| Cleanroom suitability, measured according to ISO 14644-14 | Class 5 according to ISO 14644-1 |
| Ambient temperature | -20 °C to 80 °C |
| Impact energy in end positions | 0.3 J |
| Theoretical force at 0.6 MPa (6 bar, 87 psi), return stroke | 247 N |
| Theoretical force at 0.6 MPa (6 bar, 87 psi), advance stroke | 295 N |
| Moving mass | 66 g |
| Product weight | 285 g |
| Type of mounting | Either: With through-hole; With female thread; With accessories |
| Pneumatic connection | M5 |
| Note on materials | RoHS compliant |
| Material collar screws | Steel |
| Material cover | Anodised wrought aluminium alloy |
| Material seals | TPE-U(PUR) |
| Material piston rod | High-alloy steel |
| Material cylinder barrel | Smooth-anodised wrought aluminium alloy |
Working principle and cushioning of the ADN-25-40-A-P-A
Compressed air admitted to one side of the piston pushes it while the opposite chamber exhausts; reversing the supply reverses the movement. Because the effective piston area on the rod side is smaller, the ADN-25-40-A-P-A produces 295 N advancing but 247 N on return at 6 bar, a difference of roughly 16 percent that matters for pulling loads. Cushioning is by elastic rings or plates at both ends rather than an air cushion, which keeps the body short; the datasheet gives 0.3 J as the permissible impact energy in the end positions, so high speeds with heavy loads need an external damper. A magnet on the piston allows the position to be read by proximity switches mounted on the barrel, so end positions can be monitored without any change to the cylinder.
Mass, weight and force data for sizing the ADN-25-40-A-P-A
The datasheet lists a moving mass of 66 g and a product weight of 285 g for this stroke. These figures help to check carrying structures, to estimate the kinetic energy at the end of the stroke and to confirm that a mounting bracket is rated for the cylinder. Remember that the quoted forces are theoretical values at 6 bar; friction and seal drag reduce them in practice, so a safety margin is normal in sizing. The permitted operating pressure range is 0.6 bar to 10 bar, with an ambient temperature range of -20 °C to 80 °C.
Where the ADN-25-40-A-P-A fits: related Festo parts
Compact ADN cylinders trade stroke length for installation depth. Sibling codes include ADN-40-25-I-P-A, ADN-25-40-A-P-A, ADN-32-40-A-P-A, ADN-40-25-I-PPS-A and ADN-40-50-A-P-A, differing in bore, stroke, rod-end style and cushioning. Around the ADN-25-40-A-P-A you typically need foot, flange or clevis mountings, rod-end couplers, magnetic proximity switches, push-in fittings for the M5 port and a pressure regulator with filter. Send us the complete bill of materials if you want these items quoted together.
| Part number | Bore | Stroke | Advance force at 6 bar | Cushioning | Port |
|---|---|---|---|---|---|
| ADN-40-25-I-P-A | 40 mm | 25 mm | 754 N | Elastic cushioning rings/plates at both ends | G1/8 |
| ADN-25-40-A-P-A | 25 mm | 40 mm | 295 N | Elastic cushioning rings/plates at both ends | M5 |
| ADN-32-40-A-P-A | 32 mm | 40 mm | 483 N | Elastic cushioning rings/plates at both ends | G1/8 |
| ADN-40-25-I-PPS-A | 40 mm | 25 mm | 754 N | Self-adjusting pneumatic end-position cushioning | G1/8 |
| ADN-40-50-A-P-A | 40 mm | 50 mm | 754 N | Elastic cushioning rings/plates at both ends | G1/8 |
Selection and ordering checklist for ADN-25-40-A-P-A
Choose this model for small forces and short strokes where a male rod thread simplifies the attachment.
- Bore and force: confirm that 295 N advance and 247 N return at your operating pressure, after friction losses, cover the load with margin.
- Stroke: 40 mm is fixed in this code; a different stroke is a different part number.
- Rod end: male thread with M8 thread; check that your coupler or clevis matches.
- Cushioning: elastic cushioning rings or plates at both ends; confirm this matches the moved mass and speed.
- Sensing: magnetic proximity switches can be fitted; confirm sensor type separately.
- Connection: M5 on both end covers; confirm the fittings and tube size.
- Environment: ambient range -20 °C to 80 °C; avoid aggressive media and welding spatter on the rod.
Installation, commissioning and maintenance of the ADN-25-40-A-P-A
Mount the cylinder so that the load is guided and the rod sees axial force only; side loads on the rod bearing are the most common cause of early wear. Supply clean, dry compressed air at the quality stated in the datasheet (ISO 8573-1 class [7:4:4]) and fit a filter-regulator upstream. Check the end-position behaviour at low pressure first, and add an external damper if the load is heavy. The datasheet notes that lubricated operation is possible but, once started, must be continued, so decide on lubrication at commissioning and keep to it. Inspect the wiper and piston rod surface during scheduled shutdowns, and keep spare seals or a complete spare cylinder for critical lines.
Typical applications of the ADN-25-40-A-P-A in Oman and the GCC
The 25 mm bore with a 40 mm stroke is a small compact cylinder for light assembly, small clamps, ejectors and marking stations. The male rod thread connects directly to a clevis or a floating joint. Plants in Oman and the wider GCC add extra demands: ambient heat, dust, humidity near the coast and long maintenance intervals. Check the temperature range in the table above, protect the rod from sand and abrasive dust with a bellows where needed, and ensure the compressed air is well dried so that moisture does not reach the cylinder.
Information to send with an RFQ for ADN-25-40-A-P-A
- Full type code: ADN-25-40-A-P-A (and Festo part number 536257 if known).
- Quantity and required delivery timeframe.
- Machine or plant where the part will be fitted, and whether it is a replacement or a new design.
- Nameplate photo of the existing cylinder if it is a replacement.
- Mounting accessories, proximity switches and fittings required alongside.
- Delivery destination in Oman or the GCC.
Documents and quotation
A datasheet for the ADN-25-40-A-P-A is attached on this page for reference. It lists the technical data shown above; check any application-specific limit against the document before committing to a design.
To request a quotation, send the part number ADN-25-40-A-P-A, the quantity and the delivery location. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer.
Other Models in the Festo Adn Range
Seven Star LLC supplies models from the Festo Adn range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Festo ADN-40-25-I-P-A Compact Cylinder | Automation Accessories | View details |
| Festo ADN-25-40-A-P-A Compact Cylinder | Automation Accessories | You are viewing this model |
Datasheets & Documents
- Datasheet Festo ADN-25-40-A-P-A Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Festo is a German maker of pneumatic and electric automation technology, founded in 1925 in Esslingen am Neckar by Albert Fezer and Gottlieb Stoll; the name comes from their surnames. It first made woodworking machines and power tools before moving into pneumatics in the 1950s. Festo is family-owned and still headquartered in Esslingen.
Seven Star LLC sources and supplies Festo cylinders, valves and valve terminals for machine maintenance and projects in Oman and the GCC.
Festo company profile
| Founded | 1925, Esslingen am Neckar, Germany |
|---|---|
| Founders | Albert Fezer and Gottlieb Stoll |
| Name | From FEzer and STOll |
| Headquarters | Esslingen am Neckar |
| Ownership | Family-owned |
| Product families | DSBC and ADN pneumatic cylinders, VUVG and VTUG solenoid valves and valve terminals, MS series air preparation units, CPX-AP remote I/O, EMMT servo motors and CMMT servo drives, electric axes and grippers |
Milestones
- 1925: Fezer and Stoll found the company in Esslingen.
- 1950s: Festo begins making pneumatic components.
Festo products listed
Two items show the two halves of a pneumatic circuit. The VTUG is a valve terminal: a manifold that carries a row of directional valves with common air supply and a shared electrical connection. The DSBC-32-100-PPVA-N3 is an ISO standard cylinder. Its type code reads as 32 mm piston diameter and 100 mm stroke, with adjustable end-position cushioning and a piston magnet for position sensing.
Festo products we list
Ordering Festo parts: what we need
Festo parts carry both a type code and a numeric part number on the label. Send both when you can; the part number is the shortest route to an exact match. For a cylinder give the full type code as on the listed DSBC example, plus mounting parts and proximity switches if required. For a VTUG valve terminal send the configuration code or a label photo: number of valve positions, valve functions, coil voltage and the electrical connection type all vary from one terminal to the next.
Facts checked against Festo's corporate history pages, October 2026.
Browse Festo products by category: Solenoid Valve, Valve Actuator.
FAQ
Questions about the Festo ADN-25-40-A-P-A Compact Cylinder
Answers from our engineering team on installation, compatibility and integration.
01What force does the ADN-25-40-A-P-A produce?
At 6 bar the datasheet gives a theoretical 295 N on the advance stroke and 247 N on the return stroke. Real forces are lower because of friction, so keep a safety margin when sizing the load.
02What are the operating pressure and temperature limits of the ADN-25-40-A-P-A?
The operating pressure range is 0.6 bar to 10 bar and the ambient temperature range is -20 deg C to 80 deg C. Operation outside these limits is not covered by the datasheet.
03How is the end position of the ADN-25-40-A-P-A cushioned?
The datasheet lists: Elastic cushioning rings/plates at both ends. The permitted impact energy in the end positions is 0.3 J, which limits the moved mass and speed without an external damper.
04Can proximity switches be fitted to the ADN-25-40-A-P-A?
Yes. The datasheet lists position detection via proximity switch, so magnetic switches can be mounted on the barrel. The switches themselves are separate items.
05What port and rod thread does the ADN-25-40-A-P-A have?
The pneumatic connection is M5 and the piston rod end is a male thread with M8 thread, per the datasheet. Confirm these against your fittings and couplers before ordering.


















Reviews
There are no reviews yet.