- Automation & ControlView all 2,610 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Festo
Festo DNC-63-100-PPV-A ISO 15552 Cylinder
Description
DNC-63-100-PPV-A: Festo 63 mm bore, 100 mm stroke ISO 15552 profile-barrel cylinder
The Festo Festo DNC-63-100-PPV-A (Festo part number 163405) is a double-acting ISO 15552 profile-barrel cylinder with a 63 mm piston and a 100 mm stroke, built to ISO 15552. At 6 bar it develops a theoretical 1.87 kN on the advance stroke and 1.68 kN on the return stroke, uses adjustable pneumatic cushioning at both ends, and has a male thread piston rod end with M16x1.5 thread. Seven Star LLC supplies the Festo DNC-63-100-PPV-A in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.
How to read the DNC-63-100-PPV-A type code
Every element of the type code carries a design decision. Reading it left to right avoids ordering the wrong sibling:
- DNC: Festo standards-based (profile barrel) cylinder series
- 63: piston diameter 63 mm
- 100: stroke 100 mm
- PPV: adjustable pneumatic cushioning at both ends
- A: position sensing via proximity switch available (magnet on the piston)
The datasheet remains the reference. If a type code on a nameplate differs from the code in an enquiry, send us the nameplate photo and we will confirm before quoting.
Festo DNC-63-100-PPV-A technical specifications
| Parameter | Specification |
|---|---|
| Manufacturer / part number | Festo DNC-63-100-PPV-A (Festo part number 163405) |
| Product type | ISO cylinder |
| Stroke | 100 mm |
| Piston diameter | 63 mm |
| Piston rod thread | M16x1.5 |
| Cushioning | Pneumatic cushioning, adjustable at both ends |
| Mounting position | Any |
| Conforms to standard | ISO 15552 |
| Piston-rod end | Male thread |
| Design | Piston; Piston rod; Prole barrel |
| Position detection | Via proximity switch |
| Variants | Piston rod at one end |
| Operating pressure | 0.06 MPa to 1.2 MPa; 0.6 bar to 12 bar |
| Mode of operation | Double-acting |
| Operating medium | Compressed air to ISO 8573-1:2010 [7:4:4] |
| Note on operating and pilot medium | Lubricated operation possible (in which case lubricated operation will; always be required) |
| Corrosion resistance class CRC | 2 – Moderate corrosion stress |
| LABS (PWIS) conformity | VDMA24364-B1/B2-L |
| Ambient temperature | -20 °C to 80 °C |
| Impact energy in end positions | 0.5 J |
| Cushioning length | 22 mm |
| Theoretical force at 0.6 MPa (6 bar, 87 psi), return stroke | 1682 N |
| Theoretical force at 0.6 MPa (6 bar, 87 psi), advance stroke | 1870 N |
| Moving mass for 0 mm stroke | 663 g |
| Additional moving mass per 10 mm stroke | 25 g |
| Basic weight for 0 mm stroke | 1709 g |
| Additional weight per 10 mm stroke | 73 g |
| Type of mounting | With female thread; With accessories |
| Pneumatic connection | G3/8 |
| Note on materials | RoHS compliant |
| Material cover | Die-cast aluminium; coated |
| Material seals | TPE-U(PU) |
| Material piston rod | High-alloy steel |
| Material cylinder barrel | Wrought aluminium alloy; Smooth-anodised |
Working principle and cushioning of the DNC-63-100-PPV-A
Compressed air admitted to one side of the piston pushes it while the opposite chamber exhausts; reversing the supply reverses the movement. Because the effective piston area on the rod side is smaller, the DNC-63-100-PPV-A produces 1.87 kN advancing but 1.68 kN on return at 6 bar, a difference of roughly 10 percent that matters for pulling loads. The cushioning is adjustable at both ends: a trapped air cushion decelerates the piston over 22 mm and screws let the commissioning technician trade stopping time against smoothness. The datasheet gives an impact energy of 0.5 J in the end positions, which sets the limit for moved mass and speed. A magnet on the piston allows the position to be read by proximity switches mounted on the barrel, so end positions can be monitored without any change to the cylinder.
Mass, weight and force data for sizing the DNC-63-100-PPV-A
The moving mass is 663 g for 0 mm stroke plus 25 g per additional 10 mm, giving about 913 g at 100 mm; the product weight is 1709 g plus 73 g per 10 mm, about 2439 g at 100 mm. These figures help to check carrying structures, to estimate the kinetic energy at the end of the stroke and to confirm that a mounting bracket is rated for the cylinder. Remember that the quoted forces are theoretical values at 6 bar; friction and seal drag reduce them in practice, so a safety margin is normal in sizing. The permitted operating pressure range is 0.6 bar to 12 bar, with an ambient temperature range of -20 °C to 80 °C.
Where the DNC-63-100-PPV-A fits: related Festo parts
The DNC range is another Festo ISO 15552 cylinder series, in the same mounting-dimension class as the DSBC. Sibling codes include DNC-32-100-PPV-A, DNC-40-100-PPV-A, DNC-50-100-PPV-A, DNC-63-100-PPV-A, DNC-80-100-PPV-A, DNC-100-100-PPV-A and the DNC-50-100-PPV version without position sensing. Around the DNC-63-100-PPV-A you typically need foot, flange or clevis mountings, rod-end couplers, magnetic proximity switches, push-in fittings for the G3/8 port and a pressure regulator with filter. Send us the complete bill of materials if you want these items quoted together.
| Part number | Bore | Stroke | Advance force at 6 bar | Cushioning | Port |
|---|---|---|---|---|---|
| DNC-32-100-PPV-A | 32 mm | 100 mm | 483 N | Pneumatic cushioning, adjustable at both ends | G1/8 |
| DNC-40-100-PPV-A | 40 mm | 100 mm | 754 N | Pneumatic cushioning, adjustable at both ends | G1/4 |
| DNC-50-100-PPV-A | 50 mm | 100 mm | 1178 N | Pneumatic cushioning, adjustable at both ends | G1/4 |
| DNC-63-100-PPV-A | 63 mm | 100 mm | 1870 N | Pneumatic cushioning, adjustable at both ends | G3/8 |
| DNC-80-100-PPV-A | 80 mm | 100 mm | 3016 N | Pneumatic cushioning, adjustable at both ends | G3/8 |
| DNC-100-100-PPV-A | 100 mm | 100 mm | 4712 N | Pneumatic cushioning, adjustable at both ends | G1/2 |
| DNC-50-100-PPV | 50 mm | 100 mm | 1178 N | Pneumatic cushioning, adjustable at both ends | G1/4 |
Selection and ordering checklist for DNC-63-100-PPV-A
Choose this size when a heavier ISO cylinder is needed and 80 or 100 mm is oversized.
- Bore and force: confirm that 1.87 kN advance and 1.68 kN return at your operating pressure, after friction losses, cover the load with margin.
- Stroke: 100 mm is fixed in this code; a different stroke is a different part number.
- Rod end: male thread with M16x1.5 thread; check that your coupler or clevis matches.
- Cushioning: adjustable pneumatic cushioning at both ends; confirm this matches the moved mass and speed.
- Sensing: magnetic proximity switches can be fitted; confirm sensor type separately.
- Connection: G3/8 on both end covers; confirm the fittings and tube size.
- Environment: ambient range -20 °C to 80 °C; avoid aggressive media and welding spatter on the rod.
Installation, commissioning and maintenance of the DNC-63-100-PPV-A
Mount the cylinder so that the load is guided and the rod sees axial force only; side loads on the rod bearing are the most common cause of early wear. Supply clean, dry compressed air at the quality stated in the datasheet (ISO 8573-1 class [7:4:4]) and fit a filter-regulator upstream. Open the supply gradually, then adjust the cushioning screws at both ends until the piston arrives softly without bouncing. The datasheet notes that lubricated operation is possible but, once started, must be continued, so decide on lubrication at commissioning and keep to it. Inspect the wiper and piston rod surface during scheduled shutdowns, and keep spare seals or a complete spare cylinder for critical lines.
Typical applications of the DNC-63-100-PPV-A in Oman and the GCC
The 63 mm bore with 100 mm stroke gives about 1.9 kN advance force at 6 bar and suits stamping, bending and heavier clamping applications, as well as vessel or silo gate actuation on bulk-handling lines. Plants in Oman and the wider GCC add extra demands: ambient heat, dust, humidity near the coast and long maintenance intervals. Check the temperature range in the table above, protect the rod from sand and abrasive dust with a bellows where needed, and ensure the compressed air is well dried so that moisture does not reach the cylinder.
Information to send with an RFQ for DNC-63-100-PPV-A
- Full type code: DNC-63-100-PPV-A (and Festo part number 163405 if known).
- Quantity and required delivery timeframe.
- Machine or plant where the part will be fitted, and whether it is a replacement or a new design.
- Nameplate photo of the existing cylinder if it is a replacement.
- Mounting accessories, proximity switches and fittings required alongside.
- Delivery destination in Oman or the GCC.
Documents and quotation
A datasheet for the DNC-63-100-PPV-A is attached on this page for reference. It lists the technical data shown above; check any application-specific limit against the document before committing to a design.
To request a quotation, send the part number DNC-63-100-PPV-A, the quantity and the delivery location. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer.
Other Models in the Festo Dnc Range
Seven Star LLC supplies models from the Festo Dnc range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Festo DNC-32-100-PPV-A ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DNC-40-100-PPV-A ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DNC-50-100-PPV-A ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DNC-63-100-PPV-A ISO 15552 Cylinder | Automation Accessories | You are viewing this model |
| Festo DNC-80-100-PPV-A ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DNC-100-100-PPV-A ISO 15552 Cylinder | Automation Accessories | View details |
| Festo DNC-50-100-PPV ISO 15552 Cylinder | Automation Accessories | View details |
Datasheets & Documents
- Datasheet Festo DNC-63-100-PPV-A Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Festo is a German maker of pneumatic and electric automation technology, founded in 1925 in Esslingen am Neckar by Albert Fezer and Gottlieb Stoll; the name comes from their surnames. It first made woodworking machines and power tools before moving into pneumatics in the 1950s. Festo is family-owned and still headquartered in Esslingen.
Seven Star LLC sources and supplies Festo cylinders, valves and valve terminals for machine maintenance and projects in Oman and the GCC.
Festo company profile
| Founded | 1925, Esslingen am Neckar, Germany |
|---|---|
| Founders | Albert Fezer and Gottlieb Stoll |
| Name | From FEzer and STOll |
| Headquarters | Esslingen am Neckar |
| Ownership | Family-owned |
| Product families | DSBC and ADN pneumatic cylinders, VUVG and VTUG solenoid valves and valve terminals, MS series air preparation units, CPX-AP remote I/O, EMMT servo motors and CMMT servo drives, electric axes and grippers |
Milestones
- 1925: Fezer and Stoll found the company in Esslingen.
- 1950s: Festo begins making pneumatic components.
Festo products listed
Two items show the two halves of a pneumatic circuit. The VTUG is a valve terminal: a manifold that carries a row of directional valves with common air supply and a shared electrical connection. The DSBC-32-100-PPVA-N3 is an ISO standard cylinder. Its type code reads as 32 mm piston diameter and 100 mm stroke, with adjustable end-position cushioning and a piston magnet for position sensing.
Festo products we list
Ordering Festo parts: what we need
Festo parts carry both a type code and a numeric part number on the label. Send both when you can; the part number is the shortest route to an exact match. For a cylinder give the full type code as on the listed DSBC example, plus mounting parts and proximity switches if required. For a VTUG valve terminal send the configuration code or a label photo: number of valve positions, valve functions, coil voltage and the electrical connection type all vary from one terminal to the next.
Facts checked against Festo's corporate history pages, October 2026.
Browse Festo products by category: Solenoid Valve, Valve Actuator.
FAQ
Questions about the Festo DNC-63-100-PPV-A ISO 15552 Cylinder
Answers from our engineering team on installation, compatibility and integration.
01What force does the DNC-63-100-PPV-A produce?
At 6 bar the datasheet gives a theoretical 1.87 kN on the advance stroke and 1.68 kN on the return stroke. Real forces are lower because of friction, so keep a safety margin when sizing the load.
02What are the operating pressure and temperature limits of the DNC-63-100-PPV-A?
The operating pressure range is 0.6 bar to 12 bar and the ambient temperature range is -20 deg C to 80 deg C. Operation outside these limits is not covered by the datasheet.
03How is the end position of the DNC-63-100-PPV-A cushioned?
The datasheet lists: Pneumatic cushioning, adjustable at both ends. The permitted impact energy in the end positions is 0.5 J, which limits the moved mass and speed without an external damper.
04Can proximity switches be fitted to the DNC-63-100-PPV-A?
Yes. The datasheet lists position detection via proximity switch, so magnetic switches can be mounted on the barrel. The switches themselves are separate items.
05What port and rod thread does the DNC-63-100-PPV-A have?
The pneumatic connection is G3/8 and the piston rod end is a male thread with M16x1.5 thread, per the datasheet. Confirm these against your fittings and couplers before ordering.


















Reviews
There are no reviews yet.