Brand:

Keyence FS-N11MN Digital Fiber Amplifier, Monitor Output, NPN

Description

Keyence FS-N11MN: fiber amplifier with an analog monitor output

The Keyence FS-N11MN is a main-unit fiber amplifier of the FS-N series that adds an analog monitor output to the usual switching output. Instead of only telling a PLC that a target is present, the unit also provides a 1 to 5 V signal that follows the received light level, so a controller or data logger can see how strongly the sensor sees the target. Seven Star LLC supplies the FS-N11MN in Oman and the GCC as an independent supplier in Muscat.

In the code, FS-N is the series, 11 is the main unit position, M indicates the monitor output version and N is an NPN open-collector switching output. The maker lists the type as Monitor output, cable connection.

That analog signal turns an ordinary presence sensor into a condition monitor. A slowly falling monitor voltage can warn of a dirty lens, a dusty fiber tip or a weakening target long before the switching output actually fails, which makes the FS-N11MN attractive for maintenance-minded plants.

FS-N11MN technical specifications

Parameter Specification
Manufacturer / part number Keyence / FS-N11MN
Product description Fiber Amplifier, Cable Type, Main Unit, NPN (monitor output type)
Type Monitor output, cable
Output NPN
Main unit / expansion unit Main unit
Control output 1 NPN open collector, 24 V; 100 mA or less per output; residual voltage 1 V or less
Monitor output (1-5 V) 1
External input None
Light source Red, 4-element LED
APC ON/OFF switchable (factory setting OFF)
Response time 50 µs (HIGH SPEED) / 250 µs (FINE) / 500 µs (TURBO) / 1 ms (SUPER) / 4 ms (ULTRA) / 16 ms (MEGA)
Interference prevention units 0 for HIGH SPEED; 4 for FINE; 8 for TURBO, SUPER, ULTRA and MEGA
Unit expansion Up to 16 units in total
Power voltage 12 to 24 VDC ±10 %, ripple (P-P) 10 % or less
Current consumption Normal 900 mW or less (36 mA at 24 V, 48 mA at 12 V); Eco ON 800 mW or less; Eco FULL 470 mW or less
Ambient light Incandescent lamp 20,000 lux or less; sunlight 30,000 lux or less
Ambient temperature -20 to +55 °C, no freezing (derated with more chained units)
Relative humidity 35 to 85 % RH, no condensation
Vibration / shock 10 to 55 Hz, 1.5 mm double amplitude; 500 m/s2
Case material Polycarbonate
Weight Approx. 75 g

How the FS-N11MN turns light level into a monitor signal

The amplifier works like the other FS-N units: an LED emits into the fiber, the returned light is measured, and the switching output toggles when the reading passes your threshold. The FS-N11MN also routes the measured quantity to a 1 to 5 V monitor output, so the receiving device sees a continuous value rather than a bare on/off state.

To use it well, scale the monitor signal in the controller during set-up: record the voltage with the target present and absent, and set alarm limits that sit between a healthy and a marginal reading. If the analog input is shared with other sensors, keep the monitor wire separate from power and drive cables to avoid induced noise.

Remember that the monitor signal is an additional output and does not replace the NPN switching output; both can run simultaneously, which lets you keep the discrete interlock for the machine and use the analog value for diagnostics.

Where the FS-N11MN fits: related FS-N series parts

The FS-N11MN is the choice when the standard FS-N11N or FS-N11P does not give enough process insight. FS-N13N is another cable-type NPN main unit, FS-N14N is the two-output expansion unit with an external input, and FS-N12CP is the M8 connector PNP expansion unit.

Expansion units can be added to the right of the FS-N11MN on the DIN rail, up to 16 in total; the interference-prevention rows in the table explain how many neighbouring units can run without optical crosstalk at each speed.

Selecting FS-N11MN: ordering checklist

  • Do you really need an analog monitor? If not, the standard main unit FS-N11N or FS-N11P is simpler.
  • Analog input range on your PLC or recorder: the FS-N11MN gives 1 to 5 V.
  • NPN switching output compatibility with your PLC input card.
  • Fiber unit type and length for the target.
  • Response time versus signal stability for your product.
  • Power supply 12 to 24 VDC and how many units are chained.

Installing, commissioning and maintaining FS-N11MN

Mount on DIN rail, insert fibers fully, and run the standard power-tuning set-up with the target in place. After tuning, log the monitor voltage with and without the target and note the values in the commissioning record so later drift can be compared.

Use shielded twisted-pair cable for the monitor line when it runs more than a few metres, and ground the shield at the receiving end only. Check that the receiving analog input impedance does not load the output unexpectedly.

In service, clean the fiber tip periodically, watch the monitor trend for slow decline, and replace fibers rather than re-bending. Keep a labelled spare because the monitor output is often wired into a recipe or alarm sheet.

Typical applications of FS-N11MN in Oman and the GCC

The FS-N11MN fits plants in Oman and the GCC where airborne dust, steam or oil mist slowly degrades optical sensing: bottling and packaging, pharmaceutical filling, and light assembly in industrial zones such as Rusayl and Sohar. The analog value allows condition-based cleaning rather than fixed schedules.

It is also used where a simple presence check is not enough, for example confirming that translucent film or a label has acceptable contrast before a machine continues.

FS-N series models compared with FS-N11MN

Use the table to choose between the monitor version and its neighbours.

Model Maker description / difference
FS-N11MN Main unit, NPN, with 1-5 V monitor output
FS-N11N Main unit, NPN, standard 1 output
FS-N11P Main unit, PNP, standard 1 output
FS-N14N Expansion unit, NPN, 2 outputs, 1 external input
FS-N13N Cable type main unit, NPN

Information to send with your FS-N11MN RFQ

  • Exact part number: FS-N11MN, with the quantity and any matching items listed below.
  • Whether the monitor output will be wired to an analog input, and its range.
  • Fiber units to be used (type, length, tip).
  • Output polarity of the PLC card.
  • Cabinet temperature and number of chained units.
  • Project reference, delivery location in Oman or the GCC and the lead time you need.

Documents and quotation

Send us the part number FS-N11MN and we will confirm the available documents, including the maker datasheet and instruction manual where we can provide them. Prices are quoted per request and are not shown on this page.

Seven Star LLC is an independent supplier in Muscat serving Oman and the GCC. We are not affiliated with the manufacturer, and every quotation states delivery and lead time against your RFQ.

Other Models in the Keyence Fs N Range

Seven Star LLC supplies models from the Keyence Fs N range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Keyence FS-N11N Digital Fiber Amplifier, Main Unit, NPNPhotoelectric SensorsView details
Keyence FS-N12CP Digital Fiber Amplifier, M8 Expansion, PNPPhotoelectric SensorsView details
Keyence FS-N13N Digital Fiber Amplifier, 2-Output, NPNPhotoelectric SensorsView details
Keyence FS-N11P Digital Fiber Amplifier, Main Unit, PNPAutomation AccessoriesView details
Keyence FS-N11MN Digital Fiber Amplifier, Monitor Output, NPNAutomation AccessoriesYou are viewing this model
Keyence FS-N14N Digital Fiber Amplifier Expansion Unit, NPNAutomation AccessoriesView details
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Keyence is a Japanese maker of sensors, measuring instruments and machine vision, founded in 1974 by Takemitsu Takizaki and headquartered in Osaka. It sells directly to factories and makes photoelectric and laser sensors, code readers, vision systems, measurement systems and microscopes.

Seven Star LLC sources and supplies Keyence sensors and code readers for machine builders and maintenance teams in Oman and the GCC.

Keyence company profile

Founded 1974, Japan
Founder Takemitsu Takizaki
Headquarters Osaka, Japan
Sales model Direct sales
Product families LR-Z and LR-W laser and photoelectric sensors, SR-X code readers, IV and CV-X vision systems, LJ-X laser profilers

Keyence series listed

Three series appear on this page. The LR-Z is a self-contained CMOS laser sensor. Keyence describes it as detecting by distance and by received light, with one-button teaching, a stainless steel body rated IP68/69K and a range of up to 500 mm depending on the model; the LR-ZB250CP is the listed type. The LR-W500C is a full-spectrum reflective photoelectric sensor from the LR-W series. The SR-X100 is an autofocus 2D code reader.

Keyence products we list

Family Examples
Photoelectric Sensors LR-W500C Full-Spectrum Reflective Photoe…
Laser Distance, LiDAR & Radar Sensors LR-ZB250CP LR-Z Series Self-Contained CM…
Machine Vision SR-X100 Autofocus 2D Code Reader

Ordering Keyence sensors: what we need

Keyence type codes are short but exact. Send the complete model, such as LR-ZB250CP, because the letters at the end decide the output type and the connection. Remember that many Keyence sensors need a separately ordered cable or connector, and code readers need a cable, a power supply and often a mounting bracket. List those items, the cable length, and the communication interface your PLC uses.

Facts checked against Keyence's published company profile, October 2026.

FAQ

Questions about the Keyence FS-N11MN Digital Fiber Amplifier, Monitor

Answers from our engineering team on installation, compatibility and integration.

01What is different about the FS-N11MN?
It adds a 1 to 5 V monitor output in addition to the NPN switching output, so a controller can read the received light level rather than only an on or off state.
02Is the FS-N11MN NPN or PNP?
It is NPN: one NPN open-collector control output at 24 V, 100 mA or less, with residual voltage of 1 V or less.
03Can the FS-N11MN be expanded?
Yes, up to 16 units can be connected in total, with the ambient temperature limit falling as more units are chained.
04What power does it use?
It runs on 12 to 24 VDC plus or minus 10 percent and consumes 900 mW or less in normal mode.
05Does it include fibers?
No, the fiber unit is selected separately, so give the fiber type and length with the RFQ.