Fluke 902 FC True-RMS HVAC Clamp Meter, Wireless

902 FC wireless HVAC clamp meter explained

The Fluke 902 FC True-RMS HVAC Clamp Meter (902 FC) is a true-RMS clamp meter for HVAC systems. It measures AC current to 600 A, voltage to 600 V, resistance to 60 kΩ, capacitance, microamps and contact temperature, and sends readings to a smartphone. Seven Star LLC supplies 902 FC in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer.

The 902 FC is the HVAC specialist of the clamp family. The table decodes its key data.

902 FC technical specifications

Values are from the manufacturer product page and 902 FC datasheet.

How the Fluke 902 FC True-RMS HVAC Clamp Meter works

The jaw senses AC current, while the leads and the 80BK probe provide voltage, resistance, capacitance, microamps and temperature, which are the checks an HVAC technician makes on compressors, fans, capacitors and flame sensors.

Bluetooth to Fluke Connect sends the data to a phone for logging and reporting. A technician can also place the clamp, close the panel and read from a distance to reduce exposure.

Key features

• AC current to 600 A
• Microamps for flame sensors
• Contact temperature to 400 °C
• Capacitance to 1000 µF
• Fluke Connect wireless

Where 902 FC fits and related Fluke models

The 902 FC is the clamp counterpart of the 116 HVAC multimeter. Use the 902 FC when current through conductors is needed; use the 116 when you need direct DC and AC measurement on a bench.

It has no DC current measurement through the jaw.

Selection checklist for 902 FC

Confirm the following points before ordering, so that the instrument matches the work and the safety rules of your site.

• AC-only jaw current.
• Temperature probe included.
• Smartphone use.
• Rating CAT III 600 V.

Safe use, care and maintenance of 902 FC

• Close the jaw fully and check that the faces are clean. Dirt or rust on the jaw faces causes reading errors, and a jaw that does not close completely should be taken out of service.
• Clamp only one conductor at a time. Two conductors of a single-phase pair or a three-phase set cancel each other and the 902 FC will show a value close to zero.
• Verify the clamp on a known live circuit before and after any test that decides whether equipment is safe to touch.
• Replace batteries when the low-battery indicator appears and remove them for long storage. Inspect the test leads for damage before each use of the voltage and resistance functions.
• Keep the jaw and display free of dust. In dusty Gulf sites, use the supplied case and wipe the instrument after switchgear room work.
• Respect the maximum conductor size and never clamp bare busbars unless the rating and your site procedure allow it. Treat the clamp as a measuring tool, not a switch or an isolator.
• Allow the instrument to reach ambient temperature after moving it from an air-conditioned vehicle into a hot plant area, so that condensation does not form inside the housing and the display settles.
• Schedule periodic calibration through your quality system, and keep the certificate with the instrument record so that readings used for reports remain traceable.

Typical applications of 902 FC in Oman and the GCC

Clamp meters are used for load checks on motors, feeders, chillers and pump drives. In Oman, maintenance teams at oil and gas plants, power and water utilities, desalination units and petrochemical sites use them for current surveys without opening circuits. A clamp reading showing a motor drawing more than its nameplate current points to a mechanical overload, a supply imbalance or a failing winding, while a reading near zero on a running pump suggests a lost phase or dry running. Because the circuit stays intact, these checks can be done on live equipment under a permit, which keeps downtime low during the hot summer months when cooling and pumping loads peak.

In Oman, chiller and air-handling-unit technicians in commercial and industrial buildings use the 902 FC to check compressor current, capacitors and temperature differentials during peak cooling season.

902 FC compared with nearby models

The 116 is a multimeter, not a clamp.

Information to send with an RFQ for 902 FC

To prepare an accurate quotation, please send:

• Exact model 902 FC and the quantity required.
• Maximum conductor size and expected current, so the jaw or flexible probe option can be confirmed.
• Whether wireless or smartphone use is needed on site.
• Any extra accessories such as a hanging strap, leads or a case.
• Calibration traceability paperwork if required on delivery.
• Delivery point in Oman or elsewhere in the GCC and the required date.

Storage, handling and spares for the Fluke 902 FC

Store the Fluke 902 FC in its case or holster with the test leads disconnected. Remove the batteries if the meter will not be used for several weeks, because leaking cells can damage the battery contacts. In Oman and the GCC, do not leave the instrument in a parked vehicle during summer, where cabin temperature can go well above the storage limit in the user manual.

• Inspect test leads, probes and clamps before each use and replace any lead with damaged insulation or exposed metal.
• Use only leads and accessories rated for the same or a higher measurement category than the work you do.
• Keep spare fuses of the exact type given in the manual; a wrong fuse removes the protection the meter is built with.
• Plan a regular calibration interval, often twelve months, and keep the certificate with the instrument records.

If your team uses several units of the Fluke 902 FC, it is useful to order spare test leads and batteries in the same RFQ, so that a meter is not taken out of service for a simple accessory.

Documents and quotation

A manufacturer datasheet for the Fluke 902 FC True-RMS HVAC Clamp Meter is attached on this page so that you can check the full specification before ordering. Please review it against your site requirements.

For a quotation, send the part number 902 FC, the quantity and your delivery location in Oman or the GCC through the RFQ button on this page. Availability and lead time are confirmed per request.