- Automation & ControlView all 2,648 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Servo Drives
- Pneumatic Cylinders
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Jaquet
Jaquet FTW 3013 Analogue Output Card, FT 3000
Description
Jaquet FTW 3013 analogue output card overview
The Jaquet FTW 3013 is the analogue output card of the FT 3000 overspeed protection and speed monitoring system. The manufacturer describes it as a frequency to current converter and as an auxiliary module. The module is added to a measurement channel that is built around an FTFU 3024 motherboard, and it turns measured speed or frequency values into three isolated, scalable signals that a turbine controller, a DCS or a recorder can read. It is a spare and replacement part for existing FT 3000 racks, which are found on steam turbines, gas turbines, compressors and pumps.
The module does not measure anything by itself. The sensor signal enters through the input card on the FTFU 3024 motherboard, and the value to be output is chosen in the configuration software. Each of the three outputs can be allocated one measured, calculated or stored value, for example the current speed, a voted or averaged speed, or the stored maximum speed. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.
Key features of the Jaquet FTW 3013
- Three separate analogue outputs on one card, each isolated from the other outputs, from the main electronics and from earth.
- Each output has its own range, so the start and end values can be set independently in the chosen engineering unit, such as rpm.
- Standard current outputs of 0 to 20 mA or 4 to 20 mA, programmable for a rising or a falling characteristic.
- Resolution of 12 bit with a maximum linearity error of 0.1 percent and an accuracy of 0.2 percent of the range.
- Software low pass filter on every output with a time constant that can be set between 0.0 and 9.9 seconds.
- Hot module exchange is listed by the manufacturer as a feature of the FT 3000 system, which helps when a card has to be replaced during operation.
FTW 3013 technical specifications
The table below lists the values published by the manufacturer for the analogue outputs of the FT 3000 family, which are provided by the module auxiliary module. Always compare the values with the documentation of your own rack before ordering a replacement.
| Part number | FTW 3013 |
|---|---|
| Brand | Jaquet |
| System family | FT 3000 overspeed protection and speed monitoring |
| Module type | Auxiliary analogue card, plugs into the rack next to the FTFU 3024 motherboard |
| Number of outputs | 3, each isolated and independently scalable |
| Standard output range | 0 to 20 mA or 4 to 20 mA, rising or falling characteristic |
| Maximum load, standard | 500 ohm (10 V) |
| Option S3 | 0 to 5 mA or 1 to 5 mA, maximum load 2000 ohm (10 V) |
| Option U | 0 to 10 V or 2 to 10 V, maximum load 7 kilohm (1.4 mA) |
| Maximum output voltage | 30 V |
| Resolution | 12 bit, 1 in 4096 |
| Maximum linearity error | 0.1 percent |
| Accuracy | 0.2 percent of the range |
| Temperature drift | typically plus or minus 150 ppm per kelvin, maximum plus or minus 300 ppm per kelvin |
| Isolation | 500 V, 50 Hz, 1 minute between outputs, to the main electronics and to earth |
| Output filter | software low pass filter, time constant 0.0 to 9.9 s per output |
| Supply | 18 to 33 VDC via the rack, typically 2.6 W, maximum 2.8 W |
| Power-on surge | limited to 0.1 A |
| Operating temperature | minus 5 to plus 60 degC, plus 70 degC for up to 2 hours |
| Storage temperature | minus 25 to plus 85 degC |
| Rack format | 3 HE plug-in card for a 19 inch card frame to DIN 41494 |
| Protection | plugged modules IP 20 |
Output options and signal behaviour of the FTW 3013
In the standard configuration the FTW 3013 drives current loops with a maximum load of 500 ohm, which corresponds to 10 V at 20 mA. For installations that use low level signals the manufacturer lists the option S3 with 0 to 5 mA or 1 to 5 mA and a load of up to 2000 ohm. A voltage version, option U, provides 0 to 10 V or 2 to 10 V for loads of 7 kilohm or more. The ordering code of your existing card therefore matters: confirm the output option on the type label before you request a spare.
For a step change of the speed the reaction time depends on the fixed measuring time entered in the configuration. When the input period is shorter than the fixed time, the maximum reaction time is twice the fixed time plus the maximum input period plus 7.5 ms. When the input period is longer than the fixed time, the maximum reaction time is the input period plus 7.5 ms. The analogue signal is therefore intended for indication, trending and control, while the fast trip decision stays with the limit relays of the motherboard.
Typical applications of the FTW 3013 in Oman and the GCC
FT 3000 racks are used wherever a rotating machine needs a fast and reliable overspeed trip. The manufacturer names single and dual shaft steam turbines, multi shaft aero derivative gas turbines, combined gas and steam turbine plants, compressor overspeed protection in chemical plants, pump monitoring and control, hydro electric stations and marine applications. In the Gulf region these correspond to power and desalination plants, gas processing and petrochemical sites, and oil and gas compression and pumping stations. In such plants the module carries the speed signal to the control room, the turbine governor or the plant historian.
- Utilities and power generation: speed indication of steam and gas turbine shafts for the DCS.
- Oil and gas: compressor and pump driver speed for trending and alarms.
- Water and desalination: speed feedback of large pump drives.
- Manufacturing and chemical: monitoring of turbine driven machinery.
Selection and compatibility notes for the FTW 3013
The module is intended for the FT 3000 rack system and works together with an FTFU 3024 motherboard. The same measurement channel can also include the FTV 3090 relay card, so a complete channel may be a motherboard alone or a motherboard with the relay card and the module. The supply is fed in through the local bus of the rack, so no separate power connection is needed on the card. Check the output option, the software revision of the rack and the position of the card in the frame before replacing a unit, and keep the configuration file of the rack so that the ranges can be restored if required.
Installation and commissioning of the FTW 3013
The modules are plug-in units for a 19 inch card frame of 3 HE height. Connections for sensors, outputs and supply are normally made at the rear through screw terminals or optional Termi-Point connectors, and the wiring of the FTW 3013 follows the module connection drawing supplied with the rack. Switch off or follow the hot exchange procedure of the manual, observe the dangerous voltages present in parts of the system, and plug the card into its slot. After installation, the output ranges, the allocated values, the rising or falling characteristic and the filter time constants are set through the RS 232 interface of the FTK 3072 communication module with a PC. Verify each output with a calibrated current meter before the loop is returned to service.
Maintenance of the FTW 3013
The manufacturer states a system life of 20 years, after which an overspeed protection system should be replaced, and a mean time between failures of several hundred thousand hours for the measuring channel. Keep the rack clean, dry and free of condensation, keep the operating temperature within the stated range and check the analogue outputs at the intervals required by your plant procedure. A spare FTW 3013 on the shelf shortens the repair time of an out-of-service channel.
Related products and ordering notes for the FTW 3013
Related FT 3000 modules include the FTFU 3024 motherboard with input cards, the FTV 3090 relay card, the FTK 3072 communication module, the FTBU 3034 trip chain control card and the FTZ 306x power supplies. When you ask for a quotation please quote the exact part number FTW 3013, the output option if known and the quantity.
Documents and quotation
A manufacturer product sheet for the FT 3000 family that includes the module is available as a datasheet on this page. To receive availability and lead time, send the RFQ with part number FTW 3013, the quantity and the delivery location, and Seven Star LLC will reply by return.
Datasheets & Documents
- Datasheet Jaquet FTW 3013 Analogue Output Card, FT 3000 Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Jaquet is a Swiss maker of speed sensors and speed measurement systems, based in Basel. Its sensors are used for speed and overspeed measurement on gas and steam turbines, engines, rail vehicles and automotive test benches. TE Connectivity acquired Jaquet in May 2016.
Seven Star LLC, an independent supplier in Muscat, lists Jaquet FT3000 system modules for maintenance teams in Oman and the GCC who need a like-for-like electronic module for a speed measurement rack already in service.
Jaquet company profile
| Location | Basel, Switzerland |
|---|---|
| Ownership | TE Connectivity, since 2016 |
| Markets | Power generation turbines, rail, automotive, industrial engines |
| Product families | Hall effect and inductive speed sensors, FT series speed switches and overspeed protection |
Jaquet FT3000 modules on our site
Two parts are listed at present, both belonging to the FT3000, a rack-mounted overspeed protection and speed measurement system built from plug-in cards. The FTW3013 analog module, type number 377Z-03984, is an analog output card. The FTFU3024-E01, type number 377Z-03981, is the frequency relay motherboard on which the system is based; other FTFU3024 variants carry different type numbers. A specialist distributor lists the FT3000 as discontinued, so the supply of each card has to be checked case by case.
Ordering Jaquet spare parts: what we need
Send the module designation and the full 377Z type number from the label, with any revision or serial number printed beside it. Add a photo of the label and of the rack position, and tell us which machine the system protects. For speed sensors we need the type number, thread, length, connector or cable form and the signal type.
Facts checked against TE Connectivity's acquisition announcement, October 2026.
Browse Jaquet products by category: Vibration.
FAQ
Questions about the Jaquet FTW 3013 Analogue Output Card, FT 3000
Answers from our engineering team on installation, compatibility and integration.
01What does the Jaquet FTW 3013 do?
It is the analogue output card of the FT 3000 system. It converts speed or frequency values from the FTFU 3024 motherboard into three isolated, scalable analogue outputs.
02What output ranges does the FTW 3013 provide?
The standard version gives 0 to 20 mA or 4 to 20 mA, rising or falling. Options exist for 0 to 5 mA or 1 to 5 mA (S3) and 0 to 10 V or 2 to 10 V (option U).
03How accurate is the FTW 3013 output?
The manufacturer states 12 bit resolution, a maximum linearity error of 0.1 percent and an accuracy of 0.2 percent of the range.
04Does the FTW 3013 work without an FTFU 3024?
No. It is an auxiliary module that gets its values from the FTFU 3024 motherboard of the same channel and is powered through the rack local bus.
05How do I request a quotation for the FTW 3013?
Send an RFQ with the part number FTW 3013, the output option if known, the quantity and the delivery location. No price is shown on this page.


















Reviews
There are no reviews yet.