- Automation & ControlView all 2,648 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Servo Drives
- Pneumatic Cylinders
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Itelcond
Itelcond AZS 1000 uF 450 V DC Aluminium Electrolytic Capacitor
Description
Itelcond AZS 1000 uF 450 V DC overview
The Itelcond AZS 1000 uF 450 V DC capacitor is an aluminium electrolytic capacitor of the Itelcond AZS series. The AZS has four solder pins for printed circuit boards, in contrast to the two-pin AZC version of the same family, and is rated for 105 degrees C with a 5,000 hour life. The aluminium case has a hermetic seal on a rubber bakelite cover, a pressure-release vent in the case and a self-extinguishing thermo-shrinkable sleeve made of UL94-V0 material. The 1000 uF, 450 V DC value is a typical DC-link choice for power supplies, drives and inverters.
Itelcond lists four case sizes for the 1000 uF 450 V DC rating in the AZS series, with the ordering code AZS102M450 followed by a case size code: PN (40 x 60 mm), PE (40 x 75 mm), PG (40 x 100 mm) and QE (45 x 75 mm), each ending in the digit 1 for the sleeved version. Because the supplied item depends on the case size, please state the size you need or the dimensions of the board position when you request a quotation for the AZS 1000 uF 450 V DC.
Key features of the Itelcond AZS 1000 uF 450 V DC
- Capacitance 1000 uF, tolerance plus or minus 20 percent (code M), rated voltage 450 V DC
- Four solder pins on the AZS (two pins on the AZC), pin length 6.3 mm
- Climatic category 40/105/56 and temperature range -40 to +105 degrees C
- Rated life 5,000 hours at 105 degrees C under the datasheet conditions
- Aluminium case with hermetic rubber bakelite seal and pressure-release vent on the case
- Thermo-shrinkable self-extinguishing sleeve, UL94-V0 external material; bottom not insulated
- Dissipation factor tan delta 0.10 at 100 Hz, ripple current tabulated at 85 and 105 degrees C
- Four case sizes available for the rating (PN, PE, PG, QE)
AZS 1000 uF 450 V DC technical specifications
Figures are taken from the Itelcond AZS-AZC datasheet. The ESR and impedance values are in milliohm, as in the catalogue tables.
| Parameter | Value |
|---|---|
| Series | AZS (4 pins) / AZC (2 pins), 105 C, 5,000 h |
| Capacitance / voltage | 1000 uF, 450 V DC |
| Capacitance tolerance | Plus or minus 20 percent (M) |
| Ordering code structure | AZ* 102 M 450 [case] 1 (S = 4 pins) |
| Case PN (40 x 60 mm), AZS102M450PN1 | ESR max 159, typ 110 (100 Hz); Z max 101 (10 kHz); ripple 6.0 A at 85 C, 3.2 A at 105 C |
| Case PE (40 x 75 mm), AZS102M450PE1 | ESR max 127, typ 102; Z max 96; ripple 6.5 A at 85 C, 3.6 A at 105 C |
| Case PG (40 x 100 mm), AZS102M450PG1 | ESR max 127, typ 102; Z max 96; ripple 7.4 A at 85 C, 4.1 A at 105 C |
| Case QE (45 x 75 mm), AZS102M450QE1 | ESR max 127, typ 102; Z max 96; ripple 7.0 A at 85 C, 3.9 A at 105 C |
| Dissipation factor tan delta | 0.10 at 100 Hz |
| Surge voltage | 495 V for 450 V working voltage |
| Leakage current | Maximum limit 0.004 x C x V microamperes; operating limit 0.001 x C x V, after 5 minutes at 25 C |
| Operating temperature | -40 to +105 degrees C; climatic category 40/105/56 |
| Terminals | Solder pins, 4 pins on AZS, length 6.3 mm |
| Case and sleeve | Aluminium case, thermo-shrinkable self-extinguishing sleeve, UL94-V0 |
| End-of-life criteria | Capacitance change up to 30 percent, ESR up to 3 times initial value, leakage within initial limit |
The datasheet gives temperature correction factors for ripple current of 2.40 at 50 degrees C, 1.80 at 85 degrees C and 1.00 at 105 degrees C, and frequency factors for voltages above 160 V of 0.88 at 50 Hz, 1.20 at 300 Hz and 1.40 above 1 kHz. Superimposed AC voltage plus DC voltage must not exceed the rated voltage, and reverse polarity is not allowed.
Typical applications in oil and gas, utilities, water and manufacturing
Aluminium electrolytic capacitors in the 450 V class such as the AZS 1000 uF 450 V DC are used for DC-link smoothing in variable-frequency drives, soft starters, inverters, welding equipment, UPS systems and industrial switching power supplies. In Oman and the GCC, they are frequently needed as replacement parts for drives and power electronics that serve pumps, compressors, conveyors and HVAC plants, where a failed capacitor bank can stop production.
Maintenance teams in oil and gas, utilities and manufacturing sites value an exact match for capacitance, voltage and case size, since capacitors on boards are often hard to source at short notice. The 105 degree C rating gives a thermal margin inside hot cabinets, although high ambient temperatures in the Gulf region still shorten the real service life.
Selection and compatibility notes for AZS 1000 uF 450 V DC
Match the AZS 1000 uF 450 V DC to the original component by capacitance, rated voltage, case diameter, height, pin layout (four pins) and ripple current. Because four case sizes exist, the 40 x 60 mm PN type offers lower ripple current than the taller PG or the 45 mm QE types, so choose the one that fits the footprint and meets the ripple requirement at the operating temperature. A 450 V rating with a 495 V surge limit should leave sufficient margin over the actual bus voltage.
For banks of capacitors in series, use balancing resistors and consider the tolerance of plus or minus 20 percent. The AZS has an uninsulated bottom, so keep the required clearance from conductors below the capacitor.
Installation and commissioning
Observe polarity: the capacitor must never be connected in reverse. Insert the four pins fully into the board, solder according to the manufacturer limits and avoid mechanical stress on the case. Keep the pressure-release vent in the case free so that it can operate if needed, and leave clearance above the capacitor.
After replacing a capacitor in a drive that has been stored or has been unpowered for a long time, follow the drive manufacturer instructions for reforming the DC-link capacitors, and discharge capacitors safely before work because 450 V DC stored energy is hazardous. Record the date of replacement for the AZS 1000 uF 450 V DC in the maintenance log.
Maintenance and service life
Electrolytic capacitors are wear components. The datasheet defines the end of life as a capacitance loss of 30 percent, an ESR of three times the initial value or leakage current above the limit. Monitor the temperature of the cabinet, keep ventilation filters clean and replace capacitors at the interval recommended for your equipment, not only after failure.
Inspect capacitors for bulging at the vent, electrolyte residue or discolouration during shutdowns. Replacing all capacitors in a bank together is generally recommended, so that ageing is uniform and one new part does not carry more ripple current than the old parts.
Related products and ordering notes
Customers who enquire about the AZS 1000 uF 450 V DC often also need matching accessories and neighbouring models from the same family, such as AZC two-pin capacitors of the same series, other 450 V ratings and values, and snap-in capacitors of Itelcond for larger banks. Please give the case size or dimensions of your board position.
When you send an enquiry for the AZS 1000 uF 450 V DC, please quote the full part number exactly as printed on the nameplate, the quantity, and the intended application. If you are replacing an installed unit, a photograph of the nameplate helps us confirm the AZS 1000 uF 450 V DC you need. Our team can arrange a quotation with delivery to Oman and across the GCC.
Frequently asked questions about AZS 1000 uF 450 V DC
The AZS 1000 uF 450 V DC is a four-pin PCB aluminium electrolytic capacitor with plus or minus 20 percent tolerance, 105 degrees C and 5,000 h rating and four case sizes from 40 x 60 mm to 45 x 75 mm. Check polarity, case size and ripple current when selecting.
Documents and quotation
A copy of the Itelcond datasheet for the AZC and AZS series for the AZS 1000 uF 450 V DC is available on this page for your engineering review. To request a quotation, send the RFQ with the part number AZS 1000 uF 450 V DC, the quantity, the delivery location and any certification or documentation requirements, and we will respond with availability and lead time. Please review the specification against your loop or system requirements before ordering.
Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with Itelcond. Product names and part numbers are used only to identify the item you ask for.
Datasheets & Documents
- Datasheet Itelcond AZC-AZS Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Itelcond is an Italian manufacturer of aluminum electrolytic capacitors, founded in 1976 and based in Settimo Milanese near Milan. Its catalog covers snap-in and screw-terminal electrolytic capacitors, customized capacitors tailored in capacitance, voltage, ESR and lifetime, bus bars and assembled units, and energy storage systems. Itelcond components are used in power supplies and server units, UPS systems, welding and magnetizing equipment, railway equipment, electric vehicles, industrial drives and medical equipment. The company reports ISO 9001 and ISO 14001 management systems and references CECC, DIN and IEC standards. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer; we help maintenance and panel-building teams match capacitor ratings and mounting styles to the original part, reducing downtime on repairs.
FAQ
Questions about the Itelcond AZS 1000 uF 450 V DC Aluminium
Answers from our engineering team on installation, compatibility and integration.
01What does AZS mean in the Itelcond capacitor code?
AZS denotes the four-pin PCB version of the AZ series, while AZC is the two-pin version, both rated 105 degrees C and 5,000 hours.
02Which case sizes exist for AZS 1000 uF 450 V DC?
The datasheet lists PN (40 x 60 mm), PE (40 x 75 mm), PG (40 x 100 mm) and QE (45 x 75 mm), with codes AZS102M450PN1, PE1, PG1 and QE1.
03What is the tolerance and temperature range?
The standard tolerance is plus or minus 20 percent (code M) and the temperature range is -40 to +105 degrees C.
04What ripple current can the 1000 uF 450 V AZS carry?
At 105 degrees C and 100 Hz the catalogue gives 3.2 A for the PN case, 3.6 A for PE, 4.1 A for PG and 3.9 A for QE.
05How can I order the AZS 1000 uF 450 V DC?
Send an RFQ with the part description, preferred case size, quantity and delivery location in Oman or the GCC, and Seven Star LLC will reply with availability and lead time.


















Reviews
There are no reviews yet.