- Automation & ControlView all 2,467 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- CCTV & Security
- Motor Soft Starters
- Encoders
- Safety Switches & Guard Locking
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: ifm
ifm VKV021 Vibration Monitor, 0-25 mm/s, M8 Stud, 4-20 mA
Description
ifm VKV021 Vibration Monitor, 0-25 mm/s, M8 Stud, 4-20 mA
The ifm VKV021 is a compact vibration monitor for permanent monitoring of the overall vibration, in the manner of DIN ISO 10816. It measures vibration velocity from 0 to 25 mm/s (RMS) in a frequency band of 10 to 1000 Hz using a MEMS sensor, and the measuring error is below 3 % of the final value. The switch point is set with two rings on the housing, and the response delay can be set between 1 and 60 seconds.
It has a switching output (500 mA) and a 4 to 20 mA analogue output, an IP67 housing and an M8 x 1.25 stud for mounting. Seven Star LLC supplies the VKV021 in Oman and the GCC as an independent supplier in Muscat.
VKV021 technical specifications
The table lists the values published by the manufacturer for the VKV021. Where a parameter has several operating modes, the headline value is shown; the full parameter list is in the manufacturer documentation.
| Parameter | Specification |
|---|---|
| Manufacturer / part number | ifm electronic / VKV021 |
| Operating voltage [V] | 18 to 32 DC |
| Current consumption [mA] | < 50 |
| Output signal | switching signal; analogue signal |
| Electrical design | PNP |
| Output function | normally closed |
| Permanent current rating of switching output DC [mA] | 500 |
| Analogue current output [mA] | 4 to 20 |
| Max. load [Ω] | 500 |
| Measuring error [% of the final value] | < ± 3 |
| Response time [s] | 1 to 60 |
| Ambient temperature [°C] | -25 to 80 |
| Protection | IP 67 |
| Weight [g] | 113.5 |
| Materials | PBT; PC; FKM; stainless steel (316L/1.4404) |
| Connector | 1 x M12; coding: A; Contacts: 4 |
| MTTF [years] | 510 |
How the VKV021 works
The VKV021 is a compact vibration monitor with a MEMS sensor. It measures the effective vibration velocity in the stated frequency band, for overall vibration monitoring along the lines of DIN ISO 10816, and compares it with a limit that you set using the rings on the housing. When the limit is exceeded for longer than the set delay, the output switches. An analogue 4 to 20 mA output also provides the actual level for trending.
Where the VKV021 fits and related parts
The VKV021 is the easy first step into vibration monitoring: one sensor, one machine, one alarm. When you need several measuring points or detailed history, the VSE002 diagnostic electronics collects data from up to four sensors. In many installations the two are combined, using the VKV021 as a local alarm.
Selection and ordering checklist for the VKV021
Work through the points below before you confirm the order, so that the VKV021 you receive is the one your machine or plant needs.
- Check that the vibration velocity expected is within 0 to 25 mm/s RMS
- Check the frequency band 10 to 1000 Hz covers the machine’s speeds
- Choose the M8 x 1.25 stud mounting point
- Decide on the use of the switching and analogue outputs
- Check supply 18 to 32 V DC
The manufacturer lists this article under the type designation Vibration monitor with intuitive switch point setting, VIBRATION MONITOR. The article number VKV021 is the reference to quote when ordering, and the type designation is useful for technicians who compare the label on an installed unit.
Installation, commissioning and maintenance
Stud-mount the monitor with the M8 thread at a rigid point on the bearing housing, using the stated tightening torque, so that the vibration is transmitted without damping. Connect it with an M12 cordset. At commissioning, run the machine in a healthy condition, read the value, and set the alarm ring above it with a margin. Re-check the threshold after repairs and keep records of readings so a gradual rise can be recognised.
Mount the monitor with the stud at a rigid point close to the bearing, at 15 Nm, and not on a thin cover. Record the vibration reading on a good machine and set the ring at a level above it. Its single axis means that the orientation relative to the dominant vibration direction matters.
Typical applications in Oman and the GCC
Pumps, fans, blowers, motors and cooling tower drives. In Oman and the GCC it is commonly put on utility fans and pumps which run unattended, giving an early alarm when bearings begin to wear.
Vibration monitoring pays back on unattended utility machines in hot, dusty plants, where a bearing failure can stop a whole section. Capture a healthy baseline early, because trends are more informative than single readings.
VKV021 compared with related ifm types
The table places the VKV021 next to neighbouring types in the same application group, so you can see whether a sibling would suit the job better.
| Part number | Key characteristics | Note |
|---|---|---|
| VSE002 | 4 sensor inputs, Ethernet, DIN rail | Related type |
| VKV021 | 0-25 mm/s RMS, 10-1000 Hz, M8 stud | This page |
Information to send with an RFQ for the VKV021
To prepare an accurate offer for the VKV021, please include the following with your enquiry:
- Machine type and speed range
- Mounting point and thread
- Output required: switching, analogue or both
- Cordset length
- Quantity and delivery location
Storage, handling and spares for the ifm VKV021
Keep the ifm VKV021 in its original packaging until installation, and store it indoors in a dry place without condensation. Protect connectors and cable ends from dust and moisture. In hot GCC warehouses, check that the storage temperature stays inside the range given in the manufacturer datasheet before the unit is installed.
- Check the article number and connection type against the drawing before mounting.
- Use the mounting accessories and connection cables recommended for the device, and route cables away from power wiring.
- Keep at least one spare unit of each type used on critical machines, so that a failed device can be swapped quickly.
- Record the device type, firmware version where relevant, and parameter settings, so that a replacement can be set up the same way.
When you order the ifm VKV021, include the matching cables, connectors or mounting parts in the same RFQ. This avoids delays at commissioning when a small accessory is missing.
Documents and quotation
No datasheet is attached to this page. Send us the part number VKV021 and we will confirm which documents are available, such as the datasheet and operating instructions, and for IO-Link devices the device description file.
Seven Star LLC is an independent supplier in Muscat serving Oman and the GCC and is not affiliated with the manufacturer; the name ifm is used only to identify the product. Prices are not shown on the page, so send the part number, the quantity and the delivery location to receive a quotation.
Other Models in the Ifm Vib Range
Seven Star LLC supplies models from the Ifm Vib range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| ifm VSE002 Vibration Diagnostic Electronics, Ethernet, DIN Rail | Vibration Monitoring | View details |
| ifm VKV021 Vibration Monitor, 0-25 mm/s, M8 Stud, 4-20 mA | Vibration Monitoring | You are viewing this model |
Datasheets & Documents
- Datasheet ifm VKV021 Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.
Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.
ifm company profile
| Founded | 1969, Essen, Germany |
|---|---|
| Founders | Robert Buck and Gerd Marhofer |
| Headquarters | Essen, Germany |
| Ownership | Family-owned |
| Product families | Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters |
Milestones
- 1969: ifm is founded in Essen.
- 2001: The founders' sons take over management.
ifm sensors listed on this page
ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:
- O1D100: laser distance sensor for position and distance measurement
- PN7093: pressure sensor with local display
- NG5021: inductive proximity sensor with NAMUR output
Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.
ifm products we list
Ordering ifm sensors: what we need
Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.
Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.
Browse ifm products by category: Sensors & Transmitters, Pressure Instrumentation.
FAQ
Questions about the ifm VKV021 Vibration Monitor, 0-25 mm/s, M8 Stud,
Answers from our engineering team on installation, compatibility and integration.
01What does the ifm VKV021 measure?
The overall vibration velocity in mm/s RMS from 0 to 25 mm/s.
02What is the frequency range of the VKV021?
10 to 1000 Hz. This is the value published by the manufacturer for the VKV021; confirm details before ordering.
03How is the switch point set on the VKV021?
With two setting rings on the housing. This is the value published by the manufacturer for the VKV021; confirm details before ordering.
04What outputs does the VKV021 provide?
A switching output and a 4 to 20 mA analogue output.
05How is the VKV021 mounted?
With an M8 x 1.25 stud. This is the value published by the manufacturer for the VKV021; confirm details before ordering.


















Reviews
There are no reviews yet.