Brand:

ifm LK3123 Level Sensor, 472 mm Probe, 4-20 mA, IO-Link

Description

ifm LK3123 Level Sensor, 472 mm Probe, 4-20 mA, IO-Link

The ifm LK3123 is an electronic level sensor with a 472 mm probe, an active range of 390 mm and a resolution of 5 mm. It measures water, hydrous coolants and oils with a measuring error of plus or minus 5 percent of the final value and repeatability of plus or minus 2. A 4-digit LED display shows the level.

Outputs are switching, 4 to 20 mA (invertible) and IO-Link. The wetted material is PP, the medium temperature is 0 to 35 degrees Celsius, or up to 60 degrees Celsius with the climatic tube E43101, and protection is IP67. Seven Star LLC supplies the LK3123 in Oman and the GCC as an independent supplier in Muscat.

LK3123 technical specifications

The table lists the values published by the manufacturer for the LK3123. Where a parameter has several operating modes, the headline value is shown; the full parameter list is in the manufacturer documentation.

Parameter Specification
Manufacturer / part number ifm electronic / LK3123
Resolution [mm] 5
Dimensions [mm] Ø 16
Probe length L [mm] 472
Active range A [mm] 390
Media hydrous coolants; oils; oil-based media; water; media similar to water
Medium temperature [°C] 0 to 35 (with climatic tube E43101: 35 to 60 °C)
Operating voltage [V] 18 to 30 DC
Current consumption [mA] < 50
Output signal switching signal; analogue signal; IO-Link
Electrical design PNP/NPN
Output function normally open / normally closed (parameterisable)
Permanent current rating of switching output DC [mA] 200
Analogue current output [mA] 4 to 20, invertible
Max. load [Ω] 500
Repeatability ± 2
Measuring error [% of the final value] ± 5
Communication interface IO-Link
Ambient temperature [°C] 0 to 60
Protection IP 67
Weight [g] 372
Materials stainless steel (304/1.4301); stainless steel (316L/1.4404); FKM; NBR; PBT; PC; PA; PP; TPV
Materials (wetted parts) PP
Connector 1 x M12; coding: A; Contacts: 4, gold-plated
MTTF [years] 194

How the LK3123 works

The LK3123 is a capacitive level probe: the measured medium changes the capacitance between the electrodes in the probe, and the electronics convert the covered length into a level value. The device shows the level on its LED display, and the switching output can be set to a level threshold in 5 mm steps within the active range. The probe is suited to water-based liquids, oils and coolants with a dielectric constant above the stated limit, but not to highly conductive, adhering or acidic media.

Where the LK3123 fits and related parts

The LK3123 is a fixed-length continuous rod, comparable with the LK1022 in our range. For longer or hotter tanks the LR3000 guided wave radar is an alternative.

Selection and ordering checklist for the LK3123

Work through the points below before you confirm the order, so that the LK3123 you receive is the one your machine or plant needs.

  • Confirm 472 mm probe and 390 mm active range
  • Check media: water, coolants, oils
  • Check temperature, and the need for the climatic tube
  • Choose switching or analogue output
  • Confirm 18 to 30 V DC

The manufacturer lists this article under the type designation Electronic level sensor, LK0472B-B-00KLPKG/US. The article number LK3123 is the reference to quote when ordering, and the type designation is useful for technicians who compare the label on an installed unit.

Installation, commissioning and maintenance

Mount the probe vertically through a tank opening with the accessory fitting suited to the application, leaving the stated inactive zones at the top and bottom in mind when you choose the length. Keep the probe away from baffles and fill streams, and use the climate tube accessory when the medium is warmer than the base limit. At commissioning, fill to a known level, adjust the reference point and confirm the switching output at both thresholds. Over time, clean the probe if the coolant forms a film or sludge, and check that the cable is routed away from motor leads.

Typical applications in Oman and the GCC

Coolant tanks on machine tools, hydraulic reservoirs and lubricant tanks. In Oman and the GCC the temperature limit needs attention in hot rooms.

Level sensors in tanks exposed to Gulf summers must tolerate hot product, condensation on cold nozzles and long periods without attention. Plan a periodic proof test of the alarm point, and record the output state at known levels during commissioning.

LK3123 compared with related ifm types

The table places the LK3123 next to neighbouring types in the same application group, so you can see whether a sibling would suit the job better.

Part number Key characteristics Note
LR3000 GWR, G 3/4, 100-1600 mm probe, 4-20 mA, IO-Link Related type
LMT110 Point level, G 1/2 cone, -40 to 100 C, 40 bar, IO-Link Related type
LK3123 Continuous capacitive, 472 mm, 4-20 mA, IO-Link This page
LMT100 Point level sensor Related type
LMC510 Capacitive point level sensor Related type
LK1022 Continuous level sensor Related type
LR2750 Guided wave radar Related type

Information to send with an RFQ for the LK3123

To prepare an accurate offer for the LK3123, please include the following with your enquiry:

  • Medium and its temperature profile
  • Required probe length and tank depth
  • Tank pressure and mounting fitting
  • Switching output or IO-Link requirement
  • Quantity and delivery location

Storage, handling and spares for the ifm LK3123

Keep ifm LK3123 units in their original packaging until they are mounted. Store them indoors in a dry, dust-free room, away from direct sun and condensation. Panel shops in Oman and the GCC often hold stock in warehouses that get very hot in summer, so check that storage temperature stays within the limits given in the manufacturer datasheet.

  • Check the label and order code on every unit against the drawing before it goes into the panel.
  • Use the correct tool and tightening torque for the terminals, as given in the instructions supplied with the product.
  • Keep a small number of spare units for each rating used on site, so that a failed or damaged part can be replaced without waiting for a new shipment.
  • Record the order code in the panel documentation and the as-built drawings, so that maintenance teams can reorder the same part later.

When you plan spares for a project, group the ifm LK3123 with the other parts of the same panel in one RFQ. This keeps delivery dates aligned and makes it easier to confirm stock for the whole bill of materials at once.

Documents and quotation

The official ifm data sheet for the LK3123 (document LK3123-03, English, issued 13 April 2023) is attached on this page as a PDF. It sets out the electrical data, the output function, the operating conditions, the approvals and the dimension drawing for this article. Check these values and the wiring diagram against your application before ordering, then send us the quantity and the delivery location for a quotation.

Seven Star LLC is an independent supplier in Muscat serving Oman and the GCC and is not affiliated with the manufacturer; the name ifm is used only to identify the product. Prices are not shown on the page, so send the part number, the quantity and the delivery location to receive a quotation.

Other Models in the Ifm61 Level Range

Seven Star LLC supplies models from the Ifm61 Level range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
ifm LR3000 Guided Wave Radar Level Sensor, G 3/4, 100-1600 mmAutomation AccessoriesView details
ifm LMT110 Point Level Sensor, G 1/2 Sealing Cone, PEEK, IP69KAutomation AccessoriesView details
ifm LK3123 Level Sensor, 472 mm Probe, 4-20 mA, IO-LinkAutomation AccessoriesYou are viewing this model
Datasheets & Documents
  • PDF Datasheet ifm LK3123 Data Sheet (PDF) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.

Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.

ifm company profile

Founded 1969, Essen, Germany
Founders Robert Buck and Gerd Marhofer
Headquarters Essen, Germany
Ownership Family-owned
Product families Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters

Milestones

  • 1969: ifm is founded in Essen.
  • 2001: The founders' sons take over management.

ifm sensors listed on this page

ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:

  • O1D100: laser distance sensor for position and distance measurement
  • PN7093: pressure sensor with local display
  • NG5021: inductive proximity sensor with NAMUR output

Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.

ifm products we list

Family Examples
Inductive Proximity Sensors NG5021 Inductive NAMUR Proximity Sensor
Laser Distance, LiDAR & Radar Sensors O1D100 Laser Distance Sensor
Pressure Instrumentation PN7093 Pressure Sensor with Display

Ordering ifm sensors: what we need

Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.

Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.

FAQ

Questions about the ifm LK3123 Level Sensor, 472 mm Probe, 4-20 mA,

Answers from our engineering team on installation, compatibility and integration.

01What is the probe length of the ifm LK3123?
472 mm, with an active range of 390 mm. This is the value published by the manufacturer for the LK3123; confirm details before ordering.
02What is the temperature limit of the LK3123 medium?
0 to 35 degrees Celsius, or 35 to 60 with the climatic tube E43101.
03What outputs does the LK3123 have?
Switching, 4 to 20 mA and IO-Link. This is the value published by the manufacturer for the LK3123; confirm details before ordering.
04What is the resolution of the LK3123?
5 mm. This is the value published by the manufacturer for the LK3123; confirm details before ordering.
05What are the wetted parts of the LK3123?
PP. This is the value published by the manufacturer for the LK3123; confirm details before ordering.