- Automation & ControlView all 2,718 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Servo Drives
- Pneumatic Cylinders
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: ifm
ifm PN2094 Pressure Sensor with Display, -1 to 10 bar, G 1/4
Description
ifm PN2094 Pressure Sensor with Display, -1 to 10 bar, G 1/4
The ifm PN2094 is a pressure sensor with a red/green display and a ceramic-capacitive measuring cell for liquids and gases. The measuring range is -1 to 10 bar, the process connection is a G 1/4 internal thread, the overload pressure is 75 bar and the minimum burst pressure is 150 bar. The medium temperature is -25 to 80 degrees Celsius.
It has two switching outputs, one of which can be programmed as IO-Link and one as a 4 to 20 mA analogue output. Switch point accuracy is below plus or minus 0.4 percent of the span, response time below 1.5 ms, and the sensor is built for 100 million pressure cycles. Seven Star LLC supplies the ifm PN2094 in Oman and the GCC as an independent supplier in Muscat.
PN2094 technical specifications
The table lists the values published by the manufacturer for the PN2094. Where a parameter has several operating modes, the headline value is shown; the full parameter list is in the manufacturer documentation.
| Parameter | Specification |
|---|---|
| Manufacturer / part number | ifm electronic / PN2094 |
| Measuring range | -1 to 10 bar / -14.6 to 145 psi / -0.1 to 1 MPa |
| Process connection | threaded connection G 1/4 internal thread (DIN EN ISO 1179-2) |
| Dimensions [mm] | Ø 34 / L = 90.7 |
| Measuring element | ceramic-capacitive pressure measuring cell |
| Media | liquids and gases |
| Medium temperature [°C] | -25 to 80 |
| Min. burst pressure | 150 bar / 2175 psi / 15 MPa |
| Pressure rating | 75 bar / 1087 psi / 7.5 MPa |
| Type of pressure | relative pressure; vacuum |
| Operating voltage [V] | 18 to 30 DC (to SELV/PELV) |
| Current consumption [mA] | < 35 |
| Output signal | switching signal; analogue signal; IO-Link (configurable) |
| Electrical design | PNP/NPN |
| Output function | normally open / normally closed (parameterisable) |
| Permanent current rating of switching output DC [mA] | 250 |
| Switching frequency DC [Hz] | < 500 |
| Analogue current output [mA] | 4 to 20; (scalable 1:5) |
| Max. load [Ω] | 500 |
| Switch point accuracy [% of the span] | < ± 0.4 (Turn down 1:1) |
| Repeatability [% of the span] | < ± 0.1 (with temperature fluctuations < 10 K; Turn down 1:1) |
| Long-term stability [% of the span] | < ± 0.05 (Turn down 1:1; per 6 months) |
| Response time [ms] | < 1.5 |
| Communication interface | IO-Link |
| Ambient temperature [°C] | -25 to 80 |
| Protection | IP 65; IP 67 |
| Min. pressure cycles | 100 million |
| Weight [g] | 239 |
| Materials | stainless steel (316L/1.4404); PBT+PC-GF30; PBT-GF20; PC |
| Materials (wetted parts) | stainless steel (316L/1.4404); Al2O3 (ceramics); FKM |
How the PN2094 works
Inside the PN2094 a ceramic-capacitive measuring cell converts process pressure into a small change in capacitance. The electronics linearise that signal, compensate for temperature and compare the result with the switch points you have stored. The red/green four-digit display shows the live value in the unit you select, while two yellow LEDs mirror the state of the two outputs. Because the cell is ceramic and the wetted parts are limited to stainless steel, ceramic and FKM, the same sensor handles liquids and gases without an isolating diaphragm. One output can run in IO-Link mode, which lets a controller read the pressure as process data and push parameters back to the sensor after a replacement.
Where the PN2094 fits and related parts
The PN2094 is a pressure switch with display and analogue output in one housing. The PN7094 in our range covers the same -1 to 10 bar span in the PN7 series, while the PX3224 is a transmitter without display.
Selection and ordering checklist for the PN2094
Work through the points below before you confirm the order, so that the PN2094 you receive is the one your machine or plant needs.
- Confirm the -1 to 10 bar range suits the maximum process pressure
- Confirm G 1/4 internal thread (ISO 1179-2)
- Check media compatibility with stainless steel, ceramic and FKM
- Decide which output is analogue and which IO-Link
- Check the 18 to 30 V DC supply
The manufacturer lists this article under the type designation Pressure sensor with display, PN-010-RER14-MFRKG/US/ /V. The article number PN2094 is the reference to quote when ordering, and the type designation is useful for technicians who compare the label on an installed unit.
Installation, commissioning and maintenance
Fit the sensor with a suitable sealing washer or O-ring for the thread form and tighten within the torque window printed in the table; over-tightening a ceramic cell is a common cause of zero shift. Mount it so that the connector points downward or sideways, which keeps condensation from running into the M12 interface, and rotate the process connection to align the display before final tightening. During commissioning set the unit, then the switch points and hysteresis or window, and decide whether each output is normally open or normally closed. Check that the supply stays inside 18 to 30 V DC under load. For maintenance, a periodic zero check against atmosphere on a vented line and a look at the connector for moisture are normally enough. In pulsating systems such as piston pumps, a restrictor or damper protects the cell and steadies the reading.
Typical applications in Oman and the GCC
Hydraulic and pneumatic circuits, compressors and pump discharge pressure. In Oman and the GCC it is used on compressed air systems and utility water pumps.
Pressure instruments in the Gulf face heat on sun-exposed skids, fine dust and salty humidity. Stainless steel wetted parts, a sealed M12 connection and a conservative pressure margin are the three things that decide service life. Mount the sensor out of direct sun where possible and keep the connector pointing down.
PN2094 compared with related ifm types
The table places the PN2094 next to neighbouring types in the same application group, so you can see whether a sibling would suit the job better.
| Part number | Key characteristics | Note |
|---|---|---|
| PN2094 | -1 to 10 bar, G 1/4 int., 2 outputs, IO-Link | This page |
| PG2453 | -1 to 25 bar, G 1/2 ext., LED bar graph, IP69K | Related type |
| PX3223 | 0-500 psi, 1/4 NPT ext., 4-20 mA, ceramic | Related type |
| PN7094 | Pressure sensor -1 to 10 bar | Related type |
| PX3224 | Pressure transmitter | Related type |
Information to send with an RFQ for the PN2094
To prepare an accurate offer for the PN2094, please include the following with your enquiry:
- Required pressure range and whether the process is gauge, vacuum or compound
- Medium, temperature range and any pulsation or pressure spikes
- Process thread and the sealing material you need
- Connector or cordset requirements and the cable length
- Quantity, delivery location and whether IO-Link master ports are available
Documents and quotation
The official ifm data sheet for the PN2094 (document PN2094-02, English, issued 1 March 2024) is attached on this page as a PDF. It sets out the electrical data, the output function, the operating conditions, the approvals and the dimension drawing for this article. Check these values and the wiring diagram against your application before ordering, then send us the quantity and the delivery location for a quotation.
Seven Star LLC is an independent supplier in Muscat serving Oman and the GCC and is not affiliated with the manufacturer; the name ifm is used only to identify the product. Prices are not shown on the page, so send the part number, the quantity and the delivery location to receive a quotation.
Other Models in the Ifm61 Press Range
Seven Star LLC supplies models from the Ifm61 Press range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| ifm PN2094 Pressure Sensor with Display, -1 to 10 bar, G 1/4 | Automation Accessories | You are viewing this model |
| ifm PG2453 Pressure Sensor with Analogue Display, -1 to 25 bar | Automation Accessories | View details |
| ifm PX3223 Pressure Transmitter 0-500 psi, 1/4 NPT, 4-20 mA | Automation Accessories | View details |
Datasheets & Documents
- Datasheet ifm PN2094 Data Sheet (PDF) Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.
Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.
ifm company profile
| Founded | 1969, Essen, Germany |
|---|---|
| Founders | Robert Buck and Gerd Marhofer |
| Headquarters | Essen, Germany |
| Ownership | Family-owned |
| Product families | Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters |
Milestones
- 1969: ifm is founded in Essen.
- 2001: The founders' sons take over management.
ifm sensors listed on this page
ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:
- O1D100: laser distance sensor for position and distance measurement
- PN7093: pressure sensor with local display
- NG5021: inductive proximity sensor with NAMUR output
Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.
ifm products we list
Ordering ifm sensors: what we need
Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.
Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.
Browse ifm products by category: Sensors & Transmitters, Pressure Instrumentation.
FAQ
Questions about the ifm PN2094 Pressure Sensor with Display, -1 to 10
Answers from our engineering team on installation, compatibility and integration.
01What measuring range does the ifm PN2094 have?
-1 to 10 bar. This is the value published by the manufacturer for the PN2094; confirm details before ordering.
02What process connection does the PN2094 have?
G 1/4 internal thread. This is the value published by the manufacturer for the PN2094; confirm details before ordering.
03What outputs does the PN2094 offer?
Two switching outputs, one programmable as IO-Link and one as 4 to 20 mA.
04What overload pressure does the PN2094 allow?
75 bar. This is the value published by the manufacturer for the PN2094; confirm details before ordering.
05What is the response time of the PN2094?
Below 1.5 ms. This is the value published by the manufacturer for the PN2094; confirm details before ordering.


















Reviews
There are no reviews yet.