Schneider Electric SRVS10KRILRK Easy UPS 10 kVA Rack

SRVS10KRILRK: 10 kVA 5U rackmount Easy UPS 1Ph On-Line

The SRVS10KRILRK is a Schneider Electric Easy UPS 1Ph On-Line unit rated 10000 VA / 10000 W with a sine-wave double-conversion output. It is built as a 5U rackmount chassis with a rail kit and is the extended-runtime version of its family, meaning it relies on external battery packs rather than a large internal string. Seven Star LLC supplies the SRVS10KRILRK in Oman and the GCC as an independent supplier based in Muscat.

The datasheet carries a lifecycle notice: the reference is marked discontinued, with a stated discontinuation date of 31 Oct 2026 and end of service on 30 Aug 2029. Check current availability and ask about replacement options when you enquire. The reading of the reference below is our interpretation of the product title, not a published ordering table: SRVS10KRILRK is described as an extended runtime model, with a 19-inch rail kit included, and a hard-wired output.

Installation, commissioning and maintenance of the SRVS10KRILRK

Before first start, check that the input supply, frequency and earthing agree with the datasheet, and set the nominal output voltage to match the equipment. Operate within 0–40 °C ambient, relative humidity up to 95 % without condensation and altitudes up to 3000 m; the enclosure is IP20, so the room must be clean and indoor. The upstream breaker and cable section must be sized by the installer for the full input current of a 10 kVA unit.

After commissioning, test the transfer to battery with a real load, record the runtime, and log it for later comparison. Keep the intelligent-card slot and the USB or serial port in mind if you want remote alarms. Maintenance should cover battery condition, fan and vent cleanliness, firmware or card settings and a periodic check of the bypass operation.

Technical specifications of the SRVS10KRILRK

Size, weight and mounting of the SRVS10KRILRK

The chassis measures 220 × 438 × 615 mm (H × W × D) and weighs 78 kg. It mounts horizontally in a 19-inch rack and occupies 5U of rack height; the datasheet lists mounting preference as lower in the rack, which matters because of the weight of the battery section. A rail kit is included. Check the rack depth against the 615 mm chassis and the connector space behind it.

Acoustic level is 58 dBA and heat dissipation is not listed. Heat dissipation is not given in this datasheet, so estimate losses from the efficiency figure and the real load.

Typical uses of the SRVS10KRILRK in Oman and the GCC

A 10 kVA on-line unit like SRVS10KRILRK suits telecom and network rooms, security and CCTV systems and building-management and access-control systems, where mains dips and short outages cause more damage than a long blackout would. Gulf sites also deal with high ambient temperatures, dust and unstable feeders from generators or weak grids, so the clean sine output and the input window are valuable, but room cooling and a dust-free enclosure matter just as much as the unit rating. Where the load must run longer than a standard battery allows, the external battery option is the usual route.

How the SRVS10KRILRK compares with sibling references

The nearest relatives in the same range, taken from their own datasheets, are listed here. They share the on-line topology, LCD console and card slot but differ in power, chassis and battery arrangement.

Power path and output behaviour

In on-line operation the load is always fed from the inverter, so the output is isolated from mains disturbances and the datasheet lists a sine waveform at 50/60 Hz ± 3 Hz synchronised to mains. The input accepts 230 V AC single phase with 220 V and 240 V also listed, and an auto-sensing frequency range of 40–70 Hz; the output is configurable for 220, 230 or 240 V nominal. Crest factor is 3:1 and an internal bypass is provided with both automatic and manual operation. This unit lists an efficiency of 94 % (full load) at full load.

The input window is stated as 110–300 V half load and 176–300 V full load, which describes the mains range over which the unit can carry load without going to battery. In practice that is a useful margin on weak or fluctuating supplies, but the figures belong to the datasheet and the unit’s own protection limits apply.

Connections and communication on the SRVS10KRILRK

This is a 10 kVA class unit, so both input and output are terminated as hard wire 3-wire (1P + N + E) connections instead of sockets: the installer wires a feeder in and a distribution board or load circuit out. Input protection is therefore decided by the upstream installation, and an emergency power off facility is listed on the datasheet. Plan cable sizing, breakers and earthing with a qualified electrician before ordering.

For monitoring the datasheet lists a serial port, a USB port and one free intelligent-card slot, plus a multifunction LCD status and control console and audible alarms for battery operation, low battery and continuous overload. Surge energy rating is 600 J. A network management card can be fitted in the slot where compatible, which is how most sites bring the unit onto a monitoring system; confirm the card type separately.

Information to send with an RFQ for the SRVS10KRILRK

• Exact reference SRVS10KRILRK and the quantity needed.
• Connected load in W and VA, and the required runtime.
• Available supply voltage and frequency, and the earthing arrangement.
• Whether matching battery packs, rail kits or a network card are needed in the same order.
• Delivery location and project timeline, plus any replacement requirement given the lifecycle notice.

Documents and quotation

The manufacturer datasheet for the SRVS10KRILRK is attached on this page. It carries the full specification summarised above and the lifecycle notice; check its revision date against your project.

Send us the reference SRVS10KRILRK, quantity and delivery location and Seven Star LLC will reply to your request. We supply as an independent supplier based in Muscat.