Schneider Electric XB5AK123B5 2-Pos Green Illuminated Selector

Description

XB5AK123B5: green illuminated two-position selector switch, 24 V AC/DC

The XB5AK123B5 is a Schneider Electric Harmony XB5 illuminated selector switch with a green handle, two maintained positions and an integral universal LED. It is supplied as a complete product with one NO and one NC contact, a rated supply of 24 V AC/DC at 50/60 Hz and a current draw of 18 mA. Seven Star LLC supplies the XB5AK123B5 in Oman and the GCC as an independent supplier based in Muscat, typically to panel builders who want one device that both selects a mode and shows that it is active.

The datasheet describes the product in words, so our reading of the code is an interpretation and not a manufacturer table: XB5AK is the illuminated selector, the digits give positions and contact set, and the trailing letters mark the lamp supply (B5 for 24 V AC/DC, M5 for 230 to 240 V AC), with the colour carried by the handle. Compare it with XB5AK123B5, XB5AK125M5 and XB5AK133B5 in the table below.

Typical uses of XB5AK123B5 in Oman and the GCC

Illuminated selectors are used on pump and motor starter doors, compressor and chiller panels, water-treatment skids and control desks where a mode must be readable from a distance. In oil and gas, power and desalination plants the sealed head and the LED, which needs no lamp changes, suit dusty, hot and humid areas, and a lit handle is easy to see in dim electrical rooms and in daylight glare outdoors.

Green is conventionally the normal or permitted colour: start, run, ready or valve open. Because operators read green as permission to proceed, keep it for commands that really do start or enable something. An illuminated handle repeats the colour on the lit surface, so choose it with the panel legend in front of you.

Lamp supply and LED data of the XB5AK123B5

The 24 V AC/DC at 50/60 Hz rating is a low-voltage supply that one reference can serve from a PLC output card, a 24 V DC control bus or a 24 V AC transformer winding, so panels that mix supplies can stock a single part number. Lighter wiring is also possible on the lamp circuit.

The datasheet gives supply limits of 19.2–30 V DC and 21.6–26.4 V AC and a consumption of 18 mA. The light source is a universal LED with an integral base, so there is no bulb to replace, and the stated life is 100000 h at rated voltage and 25 °C. The lamp is steady, not flashing. A surge withstand of 1 kV, 2 kV fast transients, 10 V/m field immunity, 6 kV contact and 8 kV air electrostatic discharge and Class B emission are listed, which supports use next to variable-speed drives and contactors.

Technical specifications of the XB5AK123B5

Parameter Specification
Manufacturer / part number Schneider Electric / XB5AK123B5
Range Harmony XB5
Product type Illuminated selector switch
Operator Green standard handle, stay put
Positions 2 positions 90°
Contacts 1 NO + 1 NC, slow-break, positive opening
Terminal marking (ISO) (11-12)NC, (13-14)NO
Light source Universal LED, integral
Rated supply voltage [Us] 24 V AC/DC at 50/60 Hz
Supply voltage limits 19.2–30 V DC and 21.6–26.4 V AC
Current consumption 18 mA
LED service life 100000 h at rated voltage and 25 °C
Signalling Steady
Mounting diameter 22.5 mm
Dimensions (H x W x D) 42 mm × 30 mm × 70 mm
Thermal current [Ith] 10 A
Insulation voltage [Ui] 600 V, pollution degree 3
Impulse withstand [Uimp] 6 kV
Degree of protection IP66, IP67, IP69, IP69K
Operating temperature -40 to 70 °C
Storage temperature -40 to 70 °C
Certifications BV, UL, CSA, DNV, Lloyd’s Register (LROS)
Warranty 18 months

Contact ratings and switching data of the XB5AK123B5

XB5AK123B5 carries one NO and one NC contact, terminals marked (11-12)NC, (13-14)NO under ISO numbering. With one NO and one NC contact in the same block, one position can close a circuit while it opens another, which is useful where an indicator and an interlock must change together. Note that the lamp circuit is separate from the contacts: the LED supply and the switched circuit are wired independently.

The datasheet lists a conventional thermal current of 10 A, a rated insulation voltage of 600 V at pollution degree 3 and an impulse withstand of 6 kV, with short-circuit protection by a 10 A gG cartridge fuse. Operational currents are given by utilisation category:

  • 3 A at 240 V, AC-15, A600
  • 6 A at 120 V, AC-15, A600
  • 0.1 A at 600 V, DC-13, Q600
  • 0.27 A at 250 V, DC-13, Q600
  • 0.55 A at 125 V, DC-13, Q600

The silver alloy (Ag/Ni) contacts have a rated electrical life of 1 million cycles at 2 A, 230 V, AC-15, and the mechanical life stated for the actuator is 1,000,000 cycles. Reliability at low signal levels is quoted at 5 V and 1 mA in a clean environment, which is useful when the contact feeds a PLC input rather than a coil.

Sealing, temperature and approvals of the XB5AK123B5

The datasheet lists IP66, IP67, IP69, IP69K protection with IK04 impact resistance, UL type 4X/13 enclosure type. Operation is rated from -40 to 70 °C and storage from -40 to 70 °C. Certifications listed for this reference: BV, UL, CSA, DNV, Lloyd’s Register (LROS).

This illuminated selector fits a 22.5 mm round hole, and the body depth is the same as the plain selector although the contact block and lamp make the whole unit heavier than a plain head. The datasheet drawing gives a clamping thickness of 1 to 6 mm. The body measures 30 mm wide, 42 mm high and 70 mm deep behind the panel face. Terminals are screw clamps for up to two 1.5 mm² conductors with cable ends, or at least 0.22 mm² without ends, and the recommended tightening torque is 0.8 to 1.2 N.m.

XB5AK123B5 among the illuminated selector references

These references share the contact set (1 NO + 1 NC, positive opening listed) and differ in colour, positions and lamp supply. Siblings of this unit: XB5AK125M5, XB5AK133B5.

Reference Key attributes
XB5AK123B5 2 positions 90°, stay put, 1 NO + 1 NC, green standard handle, 24 V AC/DC at 50/60 Hz
XB5AK125M5 2 positions 90°, stay put, 1 NO + 1 NC, orange standard handle, 230–240 V AC at 50/60 Hz
XB5AK133B5 3 positions ± 45°, stay put, 1 NO + 1 NC, green standard handle, 24 V AC/DC at 50/60 Hz

How the XB5AK123B5 operates

This unit has two maintained positions 90° apart. The handle stays where it is turned, and the green illuminated handle confirms that the circuit is powered, which makes a plain mode choice such as local or remote, or a permissive such as enable or inhibit, visible without a separate pilot lamp.

Selection checklist and RFQ information for XB5AK123B5

Send the points below so that the part number can be confirmed against the datasheet and checked for availability in one reply.

  • Part number XB5AK123B5 and the required quantity.
  • The lamp supply, here 24 V AC/DC at 50/60 Hz, and the panel control voltage.
  • Positions and maintained action: two positions.
  • Handle colour (green) against the project legend.
  • Panel thickness and clearance behind the door.
  • Delivery location in Oman or the GCC and the lead time you need.

Documents and quotation

The Schneider Electric datasheet for the XB5AK123B5 is attached on this page for your technical file. It carries the electrical, mechanical and environmental data summarised above, together with the dimension drawing and the panel cut-out details.

To request a quotation, send the part number and quantity through the enquiry form and we will reply with availability and delivery terms. Seven Star LLC is an independent supplier and does not act for the manufacturer, so please check the datasheet against your project requirements before ordering.

Other Models in the Se Xb5 Illum Selector Range

Seven Star LLC supplies models from the Se Xb5 Illum Selector range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Schneider Electric XB5AK123B5 2-Pos Green Illuminated SelectorAutomation AccessoriesYou are viewing this model
Schneider Electric XB5AK125M5 2-Pos Orange Illuminated SelectorAutomation AccessoriesView details
Schneider Electric XB5AK133B5 3-Pos Green Illuminated SelectorAutomation AccessoriesView details
Datasheets & Documents
  • PDF Datasheet Schneider Electric XB5AK123B5 Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Schneider Electric is the French group for energy management and industrial automation: low and medium voltage switchgear and circuit breakers, motor control, drives, PLCs, power monitoring, UPS systems and building management. Its history goes back to 1836, when the brothers Adolphe and Eugène Schneider took over the iron and steel works at Le Creusot in Burgundy. Over the 20th century the company left steel and heavy engineering and became an electrical group through acquisitions such as Merlin Gerin, Télémécanique, Square D and Modicon. Its head office is in Rueil-Malmaison near Paris, and its shares are listed on Euronext Paris.

Schneider Electric company profile

Origins 1836, Le Creusot, France: Adolphe and Eugène Schneider take over the Le Creusot foundry
Headquarters Rueil-Malmaison (Paris region), France
Ownership Public company listed on Euronext Paris
Key acquisitions Télémécanique (1988), Square D (1991), Merlin Gerin (1992), Modicon (1997), APC (2007), Invensys (2014); majority owner of AVEVA software
Brand names still in use Acti9, ComPacT and MasterPacT breakers, TeSys motor control, Altivar drives, Altistart soft starters, Modicon PLCs, Harmony control components, PowerLogic and Easergy protection and metering, APC UPS, EcoStruxure software platform
Product families Low voltage distribution, medium voltage switchgear and protection relays, motor control and drives, PLCs and HMIs, power meters, UPS and cooling, enclosures, building automation and energy software

Milestones

  • 1836: The Schneider brothers acquire the Le Creusot works; the business grows in steel, locomotives and heavy engineering.
  • 1975: First investment in Merlin Gerin, a French maker of electrical distribution equipment.
  • 1988–1992: Télémécanique, Square D (USA) and Merlin Gerin join the group, making it an electrical specialist.
  • 1997: Modicon, the company behind the first programmable logic controller, joins the group.
  • 1999: The group takes the name Schneider Electric.
  • 2007 and 2014: APC (UPS and data centre power) and Invensys (process automation) are acquired.

Choosing Schneider Electric breakers and motor control

Circuit breakers are chosen by current and breaking capacity. Acti9 miniature circuit breakers (iC60, C120) protect final circuits up to 125 A. ComPacT NSX molded case breakers cover about 16 to 630 A, and the letter after the frame size sets the breaking capacity: B, F, N, H, S, L from lowest to highest. MasterPacT air circuit breakers are used as main incomers on large switchboards. For motors, a TeSys contactor with an LRD overload relay or a GV2 motor circuit breaker suits direct starting, an Altistart soft starter reduces starting current, and an Altivar drive controls speed. The breaking capacity must always be at least the prospective short-circuit current at the point of installation.

Where Schneider Electric products are used

In Oman and the GCC, Schneider Electric equipment is found in main and sub-main switchboards of commercial and residential buildings, motor control centres in water, oil and gas and industrial plants, substations protected by Sepam and Easergy relays, data centres powered by Galaxy and APC UPS systems, and buildings controlled by EcoStruxure Building Operation.

APC by Schneider Electric: UPS and critical power

Since 2007, APC has been part of Schneider Electric and is now its product brand for uninterruptible power supplies, replacement batteries, battery packs, network management cards and rack power distribution. Our APC catalogue covers Smart-UPS line-interactive and on-line models, Easy UPS On-Line, the modular Symmetra LX, RM and PX ranges, Silcon three-phase systems and their spare part kits, and the RBC cartridges that keep them running. Schneider Electric breakers, drives and PLCs can be quoted together with APC UPS systems in one request.

Schneider Electric products we list

Family Examples
Circuit breakers Acti9 iC60N, C120N, NSX100F, NSX250N, NSX630, EasyPact EZC, MasterPacT MTZ1, MasterPacT NW
Motor control TeSys Deca LC1D, TeSys F, LRD overload relay, GV2ME08, Altistart 22, Altistart 480
Drives Altivar 12, Altivar 320, ATV340, Altivar Process 630, ATV930, Lexium 32 servo
PLCs, HMIs and relays Modicon M221, M241, M580 BMEP582040, Zelio Logic, Magelis HMISTU655
Protection, metering and power Sepam series 20, Easergy P3U30, MiCOM P139, PM5560, iEM3255, Galaxy VS UPS

Ordering Schneider Electric products: what we need

Send the commercial reference from the label (for example LC1D18M7 or ATV320U22N4C). For breakers, confirm the rated current, number of poles, breaking capacity and trip unit. For contactors, give the coil voltage. For drives, give the motor power and supply voltage. APC products are listed on their own brand page.

Facts checked against Schneider Electric's published company history, October 2026.

FAQ

Questions about the Schneider Electric XB5AK123B5 2-Pos Green

Answers from our engineering team on installation, compatibility and integration.

01What supply does the XB5AK123B5 lamp use?
The datasheet lists 24 V AC/DC at 50/60 Hz with limits of 19.2–30 V DC and 21.6–26.4 V AC and a consumption of 18 mA. It accepts AC or DC at this level.
02Can the LED of the XB5AK123B5 be replaced?
The datasheet lists the bulb base as an integral LED with a life of 100000 h, so there is no bulb to exchange.
03How many positions and contacts does the XB5AK123B5 have?
Two maintained positions (2 positions 90°) and one NO and one NC contact.
04What protection rating does the XB5AK123B5 list?
IP66, IP67, IP69, IP69K, with operation from -40 to 70 °C.
05Does Seven Star LLC supply the XB5AK123B5 in Oman?
Yes, as an independent supplier in Muscat serving Oman and the GCC. Send the part number and quantity and we confirm availability and documents.