Brand:

Beamex 8009600 Vent Valve for 40 bar Pressure Hoses

Description

Beamex 8009600 vent valve for 40 bar hoses overview

The Beamex 8009600 vent valve helps protect calibration equipment in pneumatic calibrations. Process instruments may contain moisture and dirt, and the vent valve prevents these impurities from entering the calibrator or pressure source such as a calibration pump or pressure controller.

It is used with Beamex 40 bar hoses and is connected between the device under test and the pump (PGC, PGM or ePG). Beamex notes that it must not be used during automatic pressure calibration.

This page describes Beamex 8009600 for buyers who need the exact order code. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.

Key features of the vent valve for 40 bar hoses

  • Prevents dirt and moisture from reaching the calibrator or pump
  • For use with Beamex 40 bar hoses
  • Fitted between the device under test and the PGC, PGM or ePG pump
  • Not for use during automatic pressure calibration

Standard delivery and contents according to Beamex:

  • Vent valve for 40 bar pressure hoses

Technical specifications of Beamex 8009600

Order code 8009600
Use with Beamex 40 bar hoses
Position Between device under test and pump (PGC, PGM or ePG)
Restriction Do not use during automatic pressure calibration
Medium Pneumatic (air) calibrations

All values are taken from Beamex documentation. Items not shown here are not stated in the manufacturer source and are therefore left out.

Typical applications in Oman and the GCC

Process instruments that come off a plant often carry moisture, oil residue or dirt. If that contamination enters a pump, controller or calibrator, it can damage seals and valves. Protective accessories such as the vent valve for 40 bar hoses (8009600) are therefore common in calibration workshops that serve refineries, gas plants, utilities and manufacturing sites in Oman and the GCC.

They are used on the line between the device under test and the pressure source, so that impurities are collected before they reach expensive equipment.

Selection and compatibility notes for 8009600

Confirm the pressure rating and the medium. 8009600 is intended for pneumatic calibrations, so it should not be used with liquids. Match hose thread types to the fittings of the accessory before ordering.

Where several instruments are calibrated from different sources, consider whether a protective accessory is needed on each pressure line, and keep spare seals available.

Installation and commissioning

Fit the accessory in line between the device under test and the pump or calibrator, following the order shown in the Beamex manual. Check that seals are fitted and the connections are tight before applying pressure.

Pressurize slowly, check for leaks and release pressure before disconnecting. Always observe the restrictions listed by Beamex for 8009600.

Maintenance and care

Empty or clean the accessory as the manual instructs, and replace the seals when they wear. Contamination collected in the trap is the reason it exists, so inspect it regularly if you calibrate dirty instruments.

Keep a spare seal kit with the accessory to minimize downtime.

Related products and ordering notes

Beamex lists these related items, each with its own order code:

  • 8009605 service kit for vent valve
  • 9010900 DMT40 dirt and moisture trap
  • 8009550 40 bar pressure T-hose set
  • 9021115 ePG complete kit

Beamex is a Finnish maker of calibration equipment, and its manuals and product pages are the reference for every figure on this page. Always check the manufacturer’s current documentation before putting any accessory or spare part into service.

Seven Star LLC works with industrial maintenance, procurement and calibration teams, so requests that include the full order code, the quantity and the delivery location can be answered quickly. Order codes are often the only reliable way to separate similar-looking accessories from different product generations.

Plants in the region usually plan calibration work around shutdowns, turnarounds and seasonal maintenance windows. Ordering accessories and spare parts well before the work starts avoids waiting for a missing seal, hose or cable when the plant is already offline, and it is cheaper than expediting a single item at the last minute.

Good calibration practice also depends on traceability. Records of the reference equipment, its certificate, the environmental conditions and the as-found and as-left results are what auditors and clients ask for. Accessories do not replace the calibration of the reference itself, but a worn hose, a leaking seal or a damaged cable can spoil an otherwise good measurement, which is why consumables should be replaced on a schedule rather than only after a failure.

When you compare quotations, make sure the order code is identical. Calibration accessories from the same manufacturer often differ only by thread, length or pressure rating, and a similar-looking item with a different code may not be compatible with your equipment. Keep the code on the purchase order, the goods receipt note and the maintenance record so that the same item can be reordered later.

Frequently asked questions about 8009600

What does the 8009600 vent valve do? It stops moisture and dirt from the device under test entering the calibrator or pressure source in pneumatic calibrations.

Where is it installed? Between the device under test and the pump (PGC, PGM or ePG), on Beamex 40 bar hoses.

Can it be used in automatic calibration? No. Beamex notes it must not be used during automatic pressure calibration.

Is a service kit available? Yes. Beamex lists service kit 8009605 for the vent valve.

Is there a larger trap? Yes. The DMT40 dirt and moisture trap, order code 9010900, is also listed for pneumatic use up to 40 bar.

Documents and quotation

The official Beamex PG calibration pumps brochure is attached to this page as a PDF. It covers the low-pressure pumps, hoses and fittings with which this vent valve is used. Share order code 8009600 together with your calibrator model and we will confirm the exact part in a written quotation.

Quote Beamex 8009600 exactly as written when you contact us, so that the correct item is quoted the first time. Delivery to Oman and to other GCC countries is arranged for each order, and any questions about packaging, documentation or alternative items can be raised in the same message.

Datasheets & Documents
  • PDF Datasheet Beamex PG Calibration Pumps Brochure (official PDF) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Beamex is a Finnish maker of calibration equipment and software for process instruments. Four calibration technicians founded the company in 1975 because they could not find the equipment they wanted; their first product was a voltage and current simulator, and the first factory opened in 1977. Beamex is headquartered in Pietarsaari (Jakobstad), Finland, and supplies process industries in more than 100 countries.

Seven Star LLC is an independent supplier listing Beamex documenting calibrators, temperature dry blocks, pressure controllers, calibration pumps and pressure modules for buyers in Oman and the GCC. Equipment is quoted against the model and the pressure or temperature ranges required.

Beamex company profile

Origin Founded in 1975 in Finland by four calibration technicians; first factory 1977
Headquarters Pietarsaari (Jakobstad), Finland; ISO 9001 certified since 1992
Product families MC series multifunction calibrators, temperature dry blocks, automatic and hand pressure generators, external pressure modules, CMX and LOGiCAL calibration software
Typical duty Field and workshop calibration of pressure, temperature and electrical signal instruments, including HART and fieldbus transmitters

Milestones

  • 1975: Four calibration technicians found the company in Finland.
  • 1977: The first factory opens.
  • 1992: ISO 9001 certification.

Beamex calibrators and accessories

Model Type Typical use
MC6 Advanced field calibrator and communicator Pressure, temperature and electrical calibration with a built-in HART, FOUNDATION Fieldbus and PROFIBUS PA communicator, documented results
MC6-Ex Intrinsically safe field calibrator Calibration inside Zone 0 and Zone 1 hazardous areas without a hot work permit
MC6-T Temperature calibrator with integrated dry block Temperature sensors and transmitters, with multifunction electrical and pressure measurement
MC4, MC2 Documenting and hand-held process calibrators Routine loop, transmitter and switch checks in the field
FB, MB Field and metrology temperature dry blocks FB for field calibration; MB for higher-accuracy workshop and laboratory work
ePG, POC8 Electric pressure pump and automatic pressure controller Automated pressure calibration; POC8 for workshop calibration benches
PGC, PGM, PGL, PGPH, PGHH Hand pressure pumps Pressure and vacuum generation in the field, from low pressure (PGL, ±400 mbar) to hydraulic 700 bar (PGHH)
EXT modules External pressure modules Extending MC calibrators to additional ranges, 70 kPa to 100 MPa

Where Beamex equipment is used

Instrument workshops and maintenance teams in oil and gas, refining, petrochemicals, power, water and pharmaceuticals use Beamex calibrators to verify transmitters, switches, gauges and temperature sensors. Documenting calibrators send results to calibration software, which keeps the audit trail required by quality systems and custody transfer metering procedures. Intrinsically safe models are used for in-situ calibration in classified areas.

Ordering Beamex equipment: what we need

State the model and the options you need: internal and external pressure ranges, temperature range, communication protocols (HART, FOUNDATION Fieldbus, PROFIBUS PA), Ex approval, and whether an accredited calibration certificate is required. For spare modules and pumps send the serial number of the calibrator they will be used with, so compatibility can be confirmed.

Facts checked against Beamex company history and product information, October 2026.

FAQ

Questions about the Beamex 8009600 Vent Valve for 40 bar Pressure Hoses

Answers from our engineering team on installation, compatibility and integration.

01What does the 8009600 vent valve do?
It stops moisture and dirt from the device under test entering the calibrator or pressure source in pneumatic calibrations.
02Where is it installed?
Between the device under test and the pump (PGC, PGM or ePG), on Beamex 40 bar hoses.
03Can it be used in automatic calibration?
No. Beamex notes it must not be used during automatic pressure calibration.
04Is a service kit available?
Yes. Beamex lists service kit 8009605 for the vent valve.
05Is there a larger trap?
Yes. The DMT40 dirt and moisture trap, order code 9010900, is also listed for pneumatic use up to 40 bar.