- Automation & ControlView all 2,810 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- Pneumatic Cylinders
- HMI Displays
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Bently Nevada
Bently Nevada 330103-00-05-10-02-00 3300 XL 8 mm Probe
Description
330103-00-05-10-02-00: a short metric 3300 XL probe
The Bently Nevada 330103-00-05-10-02-00 is a metric thread 3300 XL 8 mm proximity probe: M10 x 1 thread, 50 mm case, fully threaded because the unthreaded length option is 00, one metre of probe cable, no armor. It is one of the commonly stocked probe numbers named in the datasheet, which is a good sign that many machines in the field use this exact length.
The probe is the sensing end of an eddy-current transducer system; with an extension cable and a 3300 XL Proximitor sensor it produces a voltage proportional to the gap to a conductive shaft or thrust collar. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.
Reading the order code of 330103-00-05-10-02-00
| 330103 | 3300 XL 8 mm probe, M10 x 1 thread, without armor |
|---|---|
| 00 (A) | Unthreaded length 0 mm |
| 05 (B) | Overall case length 50 mm (metric increments of 10 mm) |
| 10 (C) | Total length 1.0 meter (3.3 feet) |
| 02 (D) | Miniature coaxial ClickLoc connector, standard cable, no connector protector |
| 00 (E) | No agency approval required |
Performance of the system built around 330103-00-05-10-02-00
| Linear range | 2 mm (80 mils), 0.25 to 2.3 mm from the target |
|---|---|
| Scale factor | 7.87 V/mm (200 mV/mil) plus or minus 5 percent for standard 5 or 1 meter systems |
| Deviation from straight line | Less than plus or minus 0.025 mm (1 mil) |
| Recommended gap | About 1.27 mm (50 mils), roughly -9 Vdc |
| Frequency response | 0 to 10 kHz, +0, -3 dB, with up to 305 m of field wiring |
| Minimum target | 15.2 mm (0.6 in) diameter flat target |
| Minimum shaft diameter | 50.8 mm (2 in); 76.2 mm (3 in) recommended |
| Probe tip / case | PPS plastic tip; AISI 303 or 304 stainless steel case |
| Probe resistance, 1.0 m | 7.59 plus or minus 0.50 ohm |
How 330103-00-05-10-02-00 differs from other probes in the 3300 XL 8 mm range
Change one digit and you get a different probe. 330101 has a 3/8-24 UNF thread instead of M10 x 1; 330104 is the armored metric version; 330105 and 330106 are reverse mount probes; 330140 and 330141 have smooth cases needing clamp brackets. The 3300 XL ETR probes (330193 for this thread) extend probe tip rating to 218 C. Within the same 330103 line, the 05 case length here is 50 mm, so a 330103-00-10 would be 100 mm.
Because 330103-00-05-10-02-00 has no armor, its lead is the standard 75 ohm triaxial FEP-insulated cable, a little more exposed than the armored version, which carries flexible AISI 302 or 304 stainless steel with an FEP jacket. Pick the plain probe where the lead is inside a protected conduit or drilled passage.
Mounting and installation of 330103-00-05-10-02-00
The M10 x 1 thread engages up to 15 mm, the maximum thread engagement length. Recommended case torque is 11.2 N m, with a maximum rated torque of 33.9 N m. Gap the probe at the middle of the linear range, which the datasheet gives as about 1.27 mm (-9 Vdc), then lock with the lock nut; a lock nut with safety wire holes is available as 04301008. Connector pair tightening is finger tight for two ClickLoc connectors. The datasheet recommends connector protectors on all installations, though this part number ships without them (option 02).
Typical Oman and GCC uses of 330103-00-05-10-02-00
Turbine and compressor bearing housings in oil and gas facilities often have short M10 probe pockets, so a 50 mm threaded probe like 330103-00-05-10-02-00 suits shallow bores. It is also found on motor and pump bearing caps in water and power plants, and as a speed or Keyphasor pickup on shaft keyways for the monitor channels in 3500 racks.
Spare-part notes for 330103-00-05-10-02-00
Keep matched sets: the datasheet states that probe, extension cable and Proximitor are interchangeable without bench calibration, but mixing XL and non-XL components limits performance to non-XL specifications. Record the total length of probe plus extension cable, since it must equal the Proximitor system length of 1, 5 or 9 meters.
Hazardous-area ratings and standards for 330103-00-05-10-02-00
The 3300 XL probe carries intrinsically safe marking Ex ia IIC T5 to T1 Ga when installed with zener barriers per drawing 141092 or with galvanic isolators, and Ex nA and Ex ec Zone 2 marking when installed per drawing 140979. The probe entity parameters are Ui of -28 V, Ii of 140 mA, Pi of 0.91 W, Ci of 1.5 nF and Li of 610 microhenry. Temperature class depends on ambient at the probe: T5 up to 40 C, T4 up to 80 C, T3 up to 120 C, T2 up to 177 C and T1 up to 232 C.
This particular part number ends in 00, so it was ordered without the agency approval option; if your area classification requires approvals, the E option 05 (CSA, ATEX and IECEx) must be selected and is a different part number from 330103-00-05-10-02-00.
Selection questions about 330103-00-05-10-02-00
Is the probe suitable for overspeed? The datasheet points to a separate application note on eddy-current probes in overspeed protection, so check before using any 3300 XL system for that duty. Can I use it with older 3300 5 mm components? Yes, XL and non-XL parts are interchangeable but system performance falls back to the non-XL specification. Does it need calibration? The Proximitor sensors are supplied calibrated to AISI 4140 steel by default, and other target materials are available on request.
Pair 330103-00-05-10-02-00 with a 4 meter extension cable and a 5 meter Proximitor, or use a 9 meter system with an 8 meter cable; the probe alone is a 1 meter system.
Documents and quotation
The manufacturer’s datasheet 141194 for the 3300 XL 8 mm system is attached to the page for 330103-00-05-10-02-00. Please send Seven Star LLC the part number 330103-00-05-10-02-00, the quantity and the matching cable and Proximitor numbers through the RFQ form.
Datasheets & Documents
- Datasheet Bently Nevada 330103-00-05-10-02-00 3300 XL 8 mm Probe Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Bently Nevada is the American machinery protection and condition monitoring brand behind the 3500 rack, the 3300 XL proximity probe and the System 1 software. It was founded in 1961 in Minden, Nevada, and is today a Baker Hughes business.
Seven Star LLC is an independent supplier in Muscat. We list Bently Nevada monitors, I/O modules, probes, proximitors, velocity transducers and transmitters for rotating equipment in Oman and the GCC, and source them by full part number.
Bently Nevada company profile
| Established | 1961, Minden, Nevada, USA, by Donald E. Bently. The business started earlier as Bently Scientific in Berkeley, California (1956). |
|---|---|
| Known for | The first commercial eddy-current proximity transducers for measuring shaft vibration and position on high-speed turbomachinery |
| Ownership | Acquired by GE Energy in 2002; part of Baker Hughes since GE Oil & Gas combined with Baker Hughes in 2017 |
| Rack generations | 5000 series (from 1965), 3300 series (from 1988), 3500 series (from 1995), Orbit 60 (current platform) |
| Product families | Machinery protection racks, proximity probes and proximitors, Keyphasor sensors, velocity and acceleration transducers, 2-wire vibration transmitters, general-purpose monitors, portable analyzers, wireless sensors and System 1 condition monitoring software |
| Typical machines | Steam and gas turbines, centrifugal and reciprocating compressors, pumps, motors, generators, fans and gearboxes |
Milestones
- 1956: Donald E. Bently starts Bently Scientific in Berkeley, California.
- 1961: The company moves to Minden, Nevada, as Bently Nevada.
- 1965: The 5000 series monitoring system is introduced.
- 1988: The 3300 series follows.
- 1995: The 3500 machinery protection system is launched.
- 2002 and 2017: GE Energy acquires Bently Nevada; it becomes part of Baker Hughes in 2017.
Bently Nevada product series
| Series | Type | What it does |
|---|---|---|
| 3500 | Machinery protection rack | Continuous online protection with alarm and danger relays. Modules include the 3500/15 power supply, 3500/20 rack interface, 3500/25 Keyphasor, 3500/42M proximitor/seismic, 3500/50 tachometer, 3500/60 temperature, 3500/33 relay and 3500/92 communication gateway |
| 3500 recip modules | Reciprocating compressor monitoring | 3500/70M impulse velocity, 3500/72M rod position and 3500/77M cylinder pressure |
| Orbit 60 | Protection and monitoring platform | The current Bently Nevada platform for protection, condition monitoring and data integration with System 1 |
| 3300 XL 8 mm | Proximity transducer system | Probe, extension cable and proximitor sensor for radial vibration, thrust position and Keyphasor reference on fluid-film bearing machines; also 5 mm and 25 mm versions |
| 330500 Velomitor, 190501 Velomitor CT | Piezo-velocity sensors | Casing velocity on rolling-element bearing machines and low-speed cooling tower fans |
| 990 and 991 | 2-wire transmitters | 4-20 mA vibration (990) and thrust position (991) signals straight into a PLC or DCS, without a monitor rack |
| 1900/65A, 2300 | Compact monitors | Protection for balance-of-plant pumps, fans and motors where a full 3500 rack is not justified |
A proximity probe measures the gap to the shaft, so it sees shaft movement inside a fluid-film bearing directly. A velocity or acceleration sensor sits on the casing and suits rolling-element bearing machines. Critical turbomachinery usually carries two X-Y probes per bearing, two axial probes for thrust position and a Keyphasor probe for speed and phase.
Where Bently Nevada systems are used
In Oman and the GCC, Bently Nevada racks and probes protect gas turbines, compressors and steam turbines in gas processing, LNG, refining, petrochemical, power and desalination plants. Many installations are 3500 racks that have run for years, so most requests are for like-for-like module, probe, extension cable and proximitor replacements, plus upgrades to newer monitors.
Ordering and replacement: what we need
For probes and proximitors, send the full part number with all option digits (for example 330101-00-27-10-02-05). The digits set the probe length, cable length, connector and approvals, and the probe, cable and proximitor must match in total system length. For 3500 modules, send the module and I/O part numbers from the rack and say whether the I/O is internal or external termination, or barrier type. If a module is obsolete, we quote the replacement that Bently Nevada names and point out any configuration or firmware change.
Frequently requested Bently Nevada models: Bently Nevada 3300 XL 8mm Proximity Probe, Bently Nevada 125680-01 3500/40M Proximitor I/O Module, Bently Nevada 149369-01 3500/25 Enhanced Keyphasor Module, Bently Nevada 126648-02 Isolated Keyphasor I/O Module, External, Bently Nevada 3500/61 Temperature Monitor with Recorder Outputs, Bently Nevada 3500/50M Tachometer Module.
Facts checked against Baker Hughes Bently Nevada pages and published company history, October 2026.
Browse Bently Nevada products by category: Vibration.
Planning a 3500 rack upgrade or a module replacement? Our Bently Nevada 3500 modules guide explains what each monitor, relay and communication module does, and the 3500 module replacement checklist lists the details to confirm before you order.
FAQ
Questions about the Bently Nevada 330103-00-05-10-02-00 3300 XL 8 mm
Answers from our engineering team on installation, compatibility and integration.
01How is 330103-00-05-10-02-00 decoded?
330103 is the 3300 XL 8 mm probe with M10 x 1 thread and no armor; 00 is unthreaded length, 05 a 50 mm case length, 10 a 1.0 meter total length, 02 the ClickLoc connector with standard cable and no protector, and 00 no agency approvals.
02Which Proximitor does a 1.0 m probe pair with?
A 1 meter probe is used with the 5 meter Proximitor system together with a 4 meter extension cable, or in 1 meter systems it is the probe-only system.
03What is the linear range of this probe?
Linear range is 2 mm (80 mils), running from about 0.25 mm to 2.3 mm (10 to 90 mils) from the target, with an incremental scale factor of 7.87 V/mm (200 mV/mil).
04Can this probe be used above 177 C?
No. The standard probe is rated -52 C to +177 C; the extended temperature range probes 330193 and related numbers are the options for higher temperatures.
05What do I send for a 330103-00-05-10-02-00 RFQ?
Send the full part number, the quantity, and the matching extension cable and Proximitor part numbers if you need a complete system.


















Reviews
There are no reviews yet.