Brand:

Omron E2E-C06S02-WC-B1 2M 6.5 mm Proximity Sensor

Description

The Omron E2E-C06S02-WC-B1 2M is a small cylindrical inductive proximity sensor with a 6.5 mm body diameter. It detects ferrous metal without contact, with a rated sensing distance of 2 mm, and it is built for tight spaces on small machines, clamps, cylinders and feeders.

The model code is easy to decode once you know it. E2E is the series, C means the 6.5 mm class, 06 and S02 describe the size and the shielded 2 mm sensing distance, WC marks the 2 m pre-wired cable, B1 means a PNP open-collector output with normally open operation, and 2M is the cable length. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. All numbers below come from the manufacturer small-diameter E2E datasheet.

Sensing behaviour of E2E-C06S02-WC-B1 2M

The sensor is shielded, so the sensing field is confined to the front face and the body can be flush-mounted in metal. The rated sensing distance is 2 mm plus or minus 10 percent at 23 degrees Celsius, with a recommended setting distance of 0 to 1.4 mm. The datasheet notes that working within the set distance gives faster response and more stable repeat accuracy. The standard sensing object is iron, 6.5 by 6.5 by 1 mm, and the differential travel is 15 percent or less of the sensing distance. The detection range falls with non-ferrous metals, as the engineering data in the datasheet shows.

The response frequency is 3 kHz, so the sensor can follow around 3,000 targets per second. Four indicator lamps, placed around the body, show the output state from any viewing direction, and a yellow operation indicator meeting EN 60947-5-2 lights during output.

E2E-C06S02-WC-B1 2M technical data

Parameter Value
Model E2E-C06S02-WC-B1 2M
Body 6.5 mm diameter, shielded
Sensing distance 2 mm plus or minus 10 percent (23 degrees Celsius)
Setting distance 0 to 1.4 mm
Differential travel 15 percent max. of sensing distance
Detectable object Ferrous metal
Standard sensing object Iron, 6.5 x 6.5 x 1 mm
Response frequency 3 kHz
Power supply voltage 10 to 30 V DC including 10 percent ripple
Current consumption 10 mA max.
Output PNP open collector, normally open (B1)
Load current 200 mA max. (100 mA at 60 to 70 degrees Celsius)
Residual voltage 2 V max.
Protection circuits Output and supply reverse polarity, surge suppressor, load short-circuit
Ambient temperature Minus 25 to 70 degrees Celsius
Temperature influence Plus or minus 15 percent max. of sensing distance (minus 25 to 70 degrees Celsius)
Degree of protection IP67, oil resistant (in-house standard)
Case material SUS303 stainless steel
Sensing face Heat-resistant ABS
Cable PVC, oil resistant, 2 m
Weight, pre-wired Approx. 55 g

How E2E-C06S02-WC-B1 2M differs from other E2E small-diameter variants

The small-diameter E2E family spans 3 mm, 4 mm, 5.4 mm, 6.5 mm, M4 and M5 bodies, in shielded and unshielded types. Inside that range the E2E-C06S02 is the 6.5 mm shielded model at 2 mm sensing distance. The unshielded E2E-C06N04 reaches 4 mm with a 12 by 12 mm iron target but must be mounted with free metal-free space in front. The 4 mm E2E-C04S12 senses only 1.2 mm, and the M5 E2E-S05S12 also senses 1.2 mm with a threaded body.

The suffix matters as much as the base. B1 means PNP normally open; B2 is PNP normally closed; C1 and C2 are the NPN counterparts. The WC cable type has a 2 m PVC cable, CJ means an M8 pre-wired connector at 0.3 m, and MC means an M8 connector body. A sensor with the wrong output type will not work with the PLC input card, so check the controller before ordering.

Typical uses

  • Cylinder end-position detection on small pneumatic actuators in packaging machines.
  • Detecting small steel parts in feeders and escapements.
  • Presence confirmation of screws, pins and washers in assembly stations.
  • Position sensing in compact tooling where larger 12 mm sensors do not fit.

Wiring and installation of E2E-C06S02-WC-B1 2M

Brown is plus V, blue is 0 V and black is the output. With a PNP output, the load is connected between the black wire and 0 V. The datasheet notes that using a 12 V supply and keeping output current to 20 mA or less reduces internal self-heating and gives more stable repeat accuracy. Do not mount the sensor body against a moving target, and respect the minimum distance from adjacent metal. Use the special mounting brackets sold separately, and avoid bending the cable close to the body.

Environment and reliability of E2E-C06S02-WC-B1 2M

The datasheet gives a dielectric strength of 500 V AC for one minute between the live parts and the case, and an insulation resistance of at least 50 megohm at 500 V DC. Vibration withstand is 10 to 55 Hz at 1.5 mm double amplitude for two hours in each of three axes, and shock withstand is 500 m/s2 ten times in each axis. Voltage influence is plus or minus 2.5 percent of the sensing distance across the rated voltage range of plus or minus 15 percent, and temperature drift stays within plus or minus 15 percent from minus 25 to 70 degrees Celsius. In practice these figures mean the switching point stays predictable on machines that vibrate or heat up, as long as the target is set inside the recommended setting distance. The oil-resistance claim is an in-house test in water-insoluble oil for 250 hours at 50 degrees Celsius, so the sensor suits machine tools and lubricated transfer lines, although continuous immersion in aggressive chemicals should be checked with the manufacturer.

Maintenance

Inductive sensors have no moving parts. Inspect cables for cuts, check that the body is secure, and clean metal swarf from the sensing face. If the sensing distance seems to drift, verify the supply voltage and the target material.

Documents and quotation

The E2E small-diameter datasheet is attached. Send an RFQ with the part number E2E-C06S02-WC-B1 2M, quantity and delivery location in Oman or the GCC, and we will quote.

Datasheets & Documents
  • PDF Datasheet Omron E2E-C06S02-WC-B1 2M 6.5 mm Proximity Sensor Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Omron is a Japanese electronics and automation company, founded in 1933 in Osaka by Kazuma Tateisi and now headquartered in Kyoto. Its industrial automation business makes PLCs, I/O, sensors, relays, safety components, motion control and robots. Omron's CJ and NX series controllers and I/O units are widely used in machine building.

Seven Star LLC lists Omron PLC input and output units from the CJ and NX series and supplies them to panel builders and maintenance teams in Oman.

Omron company profile

Founded 1933, Osaka, Japan
Founder Kazuma Tateisi
Headquarters Kyoto, Japan
Business Industrial automation, healthcare, electronic components
Product families CJ1/CJ2 PLCs and I/O units, NX and NJ controllers, NX I/O, E2E proximity sensors, G2R and MY relays

Omron CJ-series and NX-series units listed here

Three I/O units are on this page. The CJ1W-ID211 is a CJ-series 16-point 24 VDC input unit and the CJ1W-OC211 is a CJ-series 16-point relay output unit. The NX-ID5442 is an NX-series 16-point 24 VDC digital input unit for PNP wiring, 12 mm wide with push-in terminals. CJ and NX units belong to different hardware platforms and do not plug into each other's racks.

Omron products we list

Family Examples
PLC & I/O Cards CJ1W-ID211 CJ-Series 16-Point 24 VDC Inp…, CJ1W-OC211 CJ-Series 16-Point Relay Outp…, NX-ID5442 NX-Series 16-Point Digital Inp…

Ordering Omron PLC modules: what we need

Send the complete model number from the front or side label of the unit, including every suffix. If you are replacing a failed card, add the CPU or coupler model it is mounted with, and tell us if the terminal block or connector is needed as well. For obsolete Omron PLC parts we check which successor the manufacturer documents. Requests from other GCC countries are handled the same way.

Facts checked against Omron's published company history, October 2026.

FAQ

Questions about the Omron E2E-C06S02-WC-B1 2M 6.5 mm Proximity Sensor

Answers from our engineering team on installation, compatibility and integration.

01What does the B1 in E2E-C06S02-WC-B1 2M mean?
B1 means a PNP open-collector output with normally open operation. NPN normally open types are coded C1 in the same family.
02What is the rated sensing distance?
The rated sensing distance is 2 mm plus or minus 10 percent, with a recommended setting distance of 0 to 1.4 mm for the best repeatability.
03Can it be flush mounted?
Yes. This is a shielded type, so it can be embedded in metal; the unshielded N types need free space around the sensing face.
04What load can the output drive?
The control output carries up to 200 mA, reduced to 100 mA between 60 and 70 degrees Celsius, with a residual voltage of 2 V or less.
05What is the response frequency?
The response frequency of the E2E-C06S02 is 3 kHz, an average value from the datasheet.