Brand:

Beamex 8066770 EXT Cable for MC6 / MC5 to EXT Modules

Description

Beamex 8066770 EXT cable for MC6 and MC5 families overview

The Beamex 8066770 is the EXT cable that connects an external pressure module, EXT or EXT-IS, to MC6 family or MC5 family calibrators. It is a 4-pin to 4-pin cable.

Beamex warns that some older MC5 units have a 12-pin EXT connector, and this cable is not compatible with those units. The earlier EXT cable has been discontinued and is no longer available.

This page describes Beamex 8066770 for buyers who need the exact order code. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.

Key features of the EXT cable for MC6 and MC5 families

  • Connects EXT and EXT-IS external pressure modules
  • For MC6 family and MC5 family calibrators
  • 4-pin to 4-pin
  • Not compatible with older MC5 units that have a 12-pin EXT connector

Standard delivery and contents according to Beamex:

  • EXT cable 4-pin to 4-pin

Technical specifications of Beamex 8066770

Order code 8066770
Connector type 4-pin to 4-pin
Connects EXT / EXT-IS external pressure module
Calibrators MC6 family, MC5 family
Incompatible Older MC5 units with 12-pin EXT connector
Note Previous EXT cable discontinued

All values are taken from Beamex documentation. Items not shown here are not stated in the manufacturer source and are therefore left out.

Typical applications in Oman and the GCC

Cables and adapters are among the first accessories to wear or go missing in a busy calibration workshop. Teams that maintain Beamex calibrators and external modules in oil and gas, power, water and industrial plants across Oman and the GCC therefore stock spares such as the EXT cable for MC6 and MC5 families (8066770).

Because several generations of calibrators exist, buyers often need an exact order code to be sure the connector pinout and type are right.

Selection and compatibility notes for 8066770

Confirm the calibrator family and the accessory it must connect before ordering. 8066770 is intended only for the equipment named on this page, and similar-looking cables for other generations are not interchangeable.

Read any compatibility notes from Beamex carefully. If your unit is older, check the connector type before choosing the cable.

Installation and commissioning

Switch the calibrator off, connect both ends firmly and make sure the connectors are fully seated. Route the cable so that it does not pull on the connector when the equipment is moved.

Power on and check that the connected device is recognized. Refer to the calibrator manual for any further steps related to 8066770.

Maintenance and care

Inspect the cable for cuts, kinks and bent pins, and coil it loosely for storage. Do not pull on the cable itself when unplugging; hold the connector body.

Keep a spare cable in the field kit so that a damaged cable does not stop a calibration job.

Related products and ordering notes

Beamex lists these related items, each with its own order code:

  • 8036775 EXT cable for MC2 and MC4
  • 9270000 MC6 advanced field calibrator
  • 8066660 battery pack MC5

Beamex is a Finnish maker of calibration equipment, and its manuals and product pages are the reference for every figure on this page. Always check the manufacturer’s current documentation before putting any accessory or spare part into service.

Seven Star LLC works with industrial maintenance, procurement and calibration teams, so requests that include the full order code, the quantity and the delivery location can be answered quickly. Order codes are often the only reliable way to separate similar-looking accessories from different product generations.

Plants in the region usually plan calibration work around shutdowns, turnarounds and seasonal maintenance windows. Ordering accessories and spare parts well before the work starts avoids waiting for a missing seal, hose or cable when the plant is already offline, and it is cheaper than expediting a single item at the last minute.

Good calibration practice also depends on traceability. Records of the reference equipment, its certificate, the environmental conditions and the as-found and as-left results are what auditors and clients ask for. Accessories do not replace the calibration of the reference itself, but a worn hose, a leaking seal or a damaged cable can spoil an otherwise good measurement, which is why consumables should be replaced on a schedule rather than only after a failure.

When you compare quotations, make sure the order code is identical. Calibration accessories from the same manufacturer often differ only by thread, length or pressure rating, and a similar-looking item with a different code may not be compatible with your equipment. Keep the code on the purchase order, the goods receipt note and the maintenance record so that the same item can be reordered later.

Frequently asked questions about 8066770

What does 8066770 connect? An EXT or EXT-IS external pressure module to an MC6 family or MC5 family calibrator.

Is it compatible with all MC5 units? No. Some older MC5 units have a 12-pin EXT connector and this cable does not fit them, according to Beamex.

What connector type does it have? It is a 4-pin to 4-pin cable, so it suits only calibrators with the 4-pin EXT connector.

Is the older EXT cable still sold? No. Beamex states that the old EXT cable has been discontinued.

Which cable is used with MC2 and MC4? Cable 8036775 connects EXT modules to MC2 and MC4 family calibrators.

Documents and quotation

The official Beamex EXT external pressure modules brochure is attached to this page as a PDF. It describes the EXT external pressure modules and their cable connection to Beamex MC calibrators such as the MC6 and MC5. Send us the order code 8066770 and the serial number of your instrument and we will confirm fit and lead time in a written quotation.

Quote Beamex 8066770 exactly as written when you contact us, so that the correct item is quoted the first time. Delivery to Oman and to other GCC countries is arranged for each order, and any questions about packaging, documentation or alternative items can be raised in the same message.

Datasheets & Documents
  • PDF Datasheet Beamex EXT Pressure Modules Brochure (official PDF) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Beamex is a Finnish maker of calibration equipment and software for process instruments. Four calibration technicians founded the company in 1975 because they could not find the equipment they wanted; their first product was a voltage and current simulator, and the first factory opened in 1977. Beamex is headquartered in Pietarsaari (Jakobstad), Finland, and supplies process industries in more than 100 countries.

Seven Star LLC is an independent supplier listing Beamex documenting calibrators, temperature dry blocks, pressure controllers, calibration pumps and pressure modules for buyers in Oman and the GCC. Equipment is quoted against the model and the pressure or temperature ranges required.

Beamex company profile

Origin Founded in 1975 in Finland by four calibration technicians; first factory 1977
Headquarters Pietarsaari (Jakobstad), Finland; ISO 9001 certified since 1992
Product families MC series multifunction calibrators, temperature dry blocks, automatic and hand pressure generators, external pressure modules, CMX and LOGiCAL calibration software
Typical duty Field and workshop calibration of pressure, temperature and electrical signal instruments, including HART and fieldbus transmitters

Milestones

  • 1975: Four calibration technicians found the company in Finland.
  • 1977: The first factory opens.
  • 1992: ISO 9001 certification.

Beamex calibrators and accessories

Model Type Typical use
MC6 Advanced field calibrator and communicator Pressure, temperature and electrical calibration with a built-in HART, FOUNDATION Fieldbus and PROFIBUS PA communicator, documented results
MC6-Ex Intrinsically safe field calibrator Calibration inside Zone 0 and Zone 1 hazardous areas without a hot work permit
MC6-T Temperature calibrator with integrated dry block Temperature sensors and transmitters, with multifunction electrical and pressure measurement
MC4, MC2 Documenting and hand-held process calibrators Routine loop, transmitter and switch checks in the field
FB, MB Field and metrology temperature dry blocks FB for field calibration; MB for higher-accuracy workshop and laboratory work
ePG, POC8 Electric pressure pump and automatic pressure controller Automated pressure calibration; POC8 for workshop calibration benches
PGC, PGM, PGL, PGPH, PGHH Hand pressure pumps Pressure and vacuum generation in the field, from low pressure (PGL, ±400 mbar) to hydraulic 700 bar (PGHH)
EXT modules External pressure modules Extending MC calibrators to additional ranges, 70 kPa to 100 MPa

Where Beamex equipment is used

Instrument workshops and maintenance teams in oil and gas, refining, petrochemicals, power, water and pharmaceuticals use Beamex calibrators to verify transmitters, switches, gauges and temperature sensors. Documenting calibrators send results to calibration software, which keeps the audit trail required by quality systems and custody transfer metering procedures. Intrinsically safe models are used for in-situ calibration in classified areas.

Ordering Beamex equipment: what we need

State the model and the options you need: internal and external pressure ranges, temperature range, communication protocols (HART, FOUNDATION Fieldbus, PROFIBUS PA), Ex approval, and whether an accredited calibration certificate is required. For spare modules and pumps send the serial number of the calibrator they will be used with, so compatibility can be confirmed.

Facts checked against Beamex company history and product information, October 2026.

FAQ

Questions about the Beamex 8066770 EXT Cable for MC6 / MC5 to EXT

Answers from our engineering team on installation, compatibility and integration.

01What does 8066770 connect?
An EXT or EXT-IS external pressure module to an MC6 family or MC5 family calibrator.
02Is it compatible with all MC5 units?
No. Some older MC5 units have a 12-pin EXT connector and this cable does not fit them, according to Beamex.
03What connector type does it have?
It is a 4-pin to 4-pin cable, so it suits only calibrators with the 4-pin EXT connector.
04Is the older EXT cable still sold?
No. Beamex states that the old EXT cable has been discontinued.
05Which cable is used with MC2 and MC4?
Cable 8036775 connects EXT modules to MC2 and MC4 family calibrators.