Brand:

Pepperl+Fuchs KFD2-SCD-Ex1.LK SMART Current Driver, 4-20 mA

Description

Pepperl+Fuchs KFD2-SCD-Ex1.LK overview

The Pepperl+Fuchs KFD2-SCD-Ex1.LK is a SMART current driver from the K-System of Pepperl+Fuchs that drives SMART I/P converters, electrical valves and positioners in hazardous areas. Digital signals are superimposed on the analog values on either side and are transferred in both directions, and the current passing across the DC/DC converter is repeated at terminals 1 and 2. An open field circuit presents a high input impedance to the control side, so the control system can detect lead breakage.

If the loop resistance for digital communication is too low, an internal 250 ohm resistor between terminals 8 and 9 can serve as the HART communication resistor, and sockets for a HART communicator are built into the terminals. The datasheet, released on 23 September 2020, gives SIL 2 and describes a 20 mm wide type B1 housing. This is the earlier-generation sibling of the SCD2 model, and it is still requested as a like-for-like spare in many installed plants.

Key features of the Pepperl+Fuchs KFD2-SCD-Ex1.LK

  • SMART current driver for I/P converters, electrical valves and positioners
  • 4 to 20 mA input limited to approx. 25 mA and 4 to 20 mA output
  • Load of 100 to 700 ohm and output voltage of at least 14 V at 20 mA
  • Open field circuit gives high input impedance for lead breakage monitoring
  • Sockets for HART communicators and internal 250 ohm resistor on terminals 8 and 9
  • SIL 2 according to IEC/EN 61508
  • Supply 20 to 35 V DC through Power Rail or terminals 11 and 12
  • Housing type B1, 20 mm wide, IP20, minus 20 to 60 degrees C

KFD2-SCD-Ex1.LK technical specifications

The values below are taken from the manufacturer datasheet of the KFD2-SCD-Ex1.LK, release date 2020-09-23. Always confirm the current datasheet and the certificates before final engineering.

Parameter Value
Model KFD2-SCD-Ex1.LK, SMART Current Driver, 1-channel isolated barrier
Signal type Analog output
Safety Integrity Level SIL 2
Rated supply voltage 20 to 35 V DC (Power Rail or terminals 11+, 12-)
Power dissipation / consumption 1.1 W at 20 mA into 10 V (500 ohm) / 1.3 W
Input (control side) Terminals 7-, 8+; 4 to 20 mA limited to approx. 25 mA
Voltage drop Approx. 4 V, or internal resistance 200 ohm at 20 mA
Input resistance Above 100 kilohm when field wiring resistance is below 50 ohm, or above 800 ohm at 20 mA
Output (field side) Terminals 1+, 2-; 4 to 20 mA
Load 100 to 700 ohm
Output voltage At least 14 V at 20 mA
Hazardous-area marking (1)G [Ex ia Ga] IIC, (1)D [Ex ia Da] IIIC, (M1) [Ex ia Ma] I; certificate BAS 00 ATEX 7215
Field terminals Uo 25.2 V, Io 93 mA, Po 0.58 W
Zone 2 certificate TUV 99 ATEX 1499 X, marking Ex nA II T4
Ambient temperature Minus 20 to 60 degrees C
Dimensions / mass 20 x 115 x 115 mm (W x H x D), housing type B1 / approx. 100 g
Degree of protection / mounting IP20, screw terminals / 35 mm DIN rail

For a newer design with line fault detection and a wider ambient range, the datasheet family also includes the KFD2-SCD2-Ex1.LK. Use this older model when you need an exact replacement of an installed unit.

Typical applications in oil and gas, utilities, water and manufacturing

Control valves, I/P converters and electropneumatic positioners are the final elements of most process loops in oil and gas, power and water plants, and many of them sit in Zone 1 or Zone 2 areas. The KFD2-SCD-Ex1.LK delivers the control signal from the safe area to such devices through an intrinsically safe circuit, so the plant can keep a standard analog output card while the field circuit stays safe.

Typical uses in Oman and the wider GCC include flow and pressure control valves on pipelines, anti-surge and recycle valves on compressor trains, and dosing or level control in water treatment works. Because the module is a galvanic isolator, ground loops between the control room and a distant field device are also avoided, which can improve signal quality on long cable runs.

Selection and compatibility notes for KFD2-SCD-Ex1.LK

Compare the load of the field device with the output capability of the KFD2-SCD-Ex1.LK. Positioners and I/P converters differ in their input resistance and operating voltage, and the datasheet gives the maximum load and available voltage at 20 mA. The control-side input must also be able to drive the module, which presents a voltage drop in series with the loop.

Decide whether you need HART signals to pass through. Where an asset management system communicates with smart positioners, the signal path must support bi-directional digital communication; where the loop carries a plain analog signal, a simpler driver may be sufficient. Share the loop data with us if you are unsure which variant of the KFD2-SCD-Ex1.LK family suits the device.

Installation and commissioning of the KFD2-SCD-Ex1.LK

Before mounting the KFD2-SCD-Ex1.LK, confirm the field device and cable parameters against the entity values in the datasheet and the certificate, and decide whether the module will be powered from a Power Rail or from its own supply terminals. Mount it on a 35 mm DIN rail in a clean, ventilated cabinet in the safe area, keep hazardous-area and safe-area wiring physically separated and labelled, and respect the spacing and marking required by your site rules for intrinsically safe circuits. When replacing an installed unit, compare the terminal numbers carefully, because the supply terminals of the KFD2-SCD-Ex1.LK are 11 and 12 and differ from some newer models.

Wire the KFD2-SCD-Ex1.LK only to the terminal assignment printed in the wiring diagram, tighten the screws and check that no strands are left outside the clamp. After applying the supply, check the power indication, then simulate the field signal and prove the complete loop from field to control system before the plant is handed over. Record the as-found readings so that later loop checks of the KFD2-SCD-Ex1.LK can be compared with the commissioning values.

Maintenance and service life

The KFD2-SCD-Ex1.LK has no serviceable parts, so maintenance is mostly inspection. During planned shutdowns, check terminals for looseness and corrosion, verify the supply voltage at the module, and repeat the loop check that was recorded at commissioning. In coastal and humid locations such as Muscat, Sohar and Duqm, a clean, dry and sealed cabinet greatly extends the life of any electronic interface. Keep one KFD2-SCD-Ex1.LK as a spare for critical control valves, since positioner loops cannot usually run without their driver.

If a loop drifts out of tolerance or the unit shows no power indication with a healthy supply, replace the module instead of attempting a repair, and keep the replacement documentation in the loop folder. Certified intrinsically safe equipment must not be modified, and any change to cabling, load or field device should be re-assessed against the KFD2-SCD-Ex1.LK entity parameters before it returns to service.

Related products and ordering notes

Customers who ask for the KFD2-SCD-Ex1.LK often need neighbouring models or accessories from the same system, such as other K-System current and voltage drivers, SMART current drivers, the Power Rail and power feed modules, and matching KFD2 transmitter power supplies. If you are standardising a cabinet on one family, send us the loop list and we can quote the matching modules together.

When you send an enquiry for the KFD2-SCD-Ex1.LK, quote the full part number exactly as printed on the nameplate, the quantity and the intended application. If you are replacing an installed unit, a photograph of the nameplate helps us confirm the exact variant you need. We can arrange a quotation with delivery to Oman and across the GCC.

Frequently asked questions about KFD2-SCD-Ex1.LK

The KFD2-SCD-Ex1.LK is a SIL 2 SMART current driver with 4 to 20 mA input and output, a load of 100 to 700 ohm, HART passthrough and a 20 to 35 V DC supply.

Documents and quotation

A copy of the manufacturer datasheet for the KFD2-SCD-Ex1.LK is attached to this page for your engineering review. To request a quotation, send the RFQ with the part number KFD2-SCD-Ex1.LK, the quantity, the delivery location and any certification or documentation requirements, and we will reply with availability and lead time. Please check the specification against your loop or system requirements before ordering.

Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with Pepperl+Fuchs. Product names and part numbers are used only to identify the item you ask for.

Datasheets & Documents
  • PDF Datasheet KFD2-SCD-Ex1.LK Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Pepperl+Fuchs is a German manufacturer of industrial sensors and explosion protection equipment, founded in 1945 in Mannheim by Walter Pepperl and Ludwig Fuchs as a radio repair shop. Defective transformers led them into manufacturing, and the company developed its first proximity switch in the late 1950s. Pepperl+Fuchs is headquartered in Mannheim and is a pioneer of intrinsically safe electrical equipment for hazardous areas.

Seven Star LLC lists Pepperl+Fuchs sensors, isolated barriers, power supplies and hazardous-area mobile devices, and supplies them to instrument and automation teams in Oman by exact model designation.

Pepperl+Fuchs company profile

Founded 1945, Mannheim-Sandhofen, Germany, by Walter Pepperl and Ludwig Fuchs
Headquarters Mannheim, Germany
Ownership Privately owned (Pepperl+Fuchs SE)
Origins Radio repair workshop that began making replacement transformers
Product families Inductive, capacitive, ultrasonic and photoelectric sensors, rotary encoders, R2000 LiDAR scanners, KFD and HiC isolated barriers, Zener barriers, remote I/O, purge and pressurization systems, Ex-rated enclosures

Milestones

  • 1945: Walter Pepperl and Ludwig Fuchs open their radio repair shop in Mannheim.
  • 1958: The first proximity switch is developed (some company sources say 1959).

Pepperl+Fuchs product families on this page

On the interface side there are two systems. The K-System mounts on DIN rail and is represented here by the KFD2-UT2-Ex2 universal temperature converter. The H-System plugs into termination boards and is represented by the HiD2030 SMART transmitter power supply with HART. The PS1000-A6-24.20 is a 24 VDC, 20 A power supply for cabinets. Sensors listed include the NJ2-12GK-SN NAMUR inductive sensor, the R101 retro-reflective photoelectric sensor and the R2000 2-D LiDAR scanner. For field staff there are the Tab-Ex 05 DZ1 tablet for Zone 1/21 areas and the Smart-Ex 03 DZ2 smartphone for Zone 2/22 and Division 2 areas.

Where Pepperl+Fuchs equipment is used

Isolated barriers sit between field instruments in Zone 0 or Zone 1 and the DCS or safety system in refineries, gas plants and chemical works. NAMUR sensors report valve position and machine states in classified areas. Photoelectric sensors and LiDAR scanners work in conveying, packaging, warehousing and vehicle guidance. Ex-rated tablets and phones are carried on operator rounds and maintenance jobs.

Pepperl+Fuchs products we list

Family Examples
Isolator & Barrier HiD2030 SMART Transmitter Power Supply w…, KFD2-SR2-Ex2.W K-System Isolated Switch…, KFD2-UT2-Ex2 Universal Temperature Conve…
Industrial Computers Tab-Ex 05 DZ1 WWAN Hazardous Area Tablet, Smart-Ex® 03 DZ2 smartphone for Zone 2/2…
Inductive Proximity Sensors NJ2-12GK-SN NAMUR Inductive Sensor
Power Modules PS1000-A6-24.20 Power Supply 24 VDC 20 A
Photoelectric Sensors R101 Retro-Reflective Photoelectric Sensor
Laser Distance, LiDAR & Radar Sensors R2000 2-D LiDAR Laser Scanner

Ordering Pepperl+Fuchs parts: what we need

Send the complete model designation as printed on the device, including every suffix; a single letter can change the supply voltage or the output type. Add the part number if the label shows one. For barriers, tell us the field device and signal type, the number of channels and whether the safety loop needs a SIL-assessed module. For mobile devices, state the zone or division and the regional radio version.

Facts checked against Pepperl+Fuchs's own chronicle pages, October 2026.

FAQ

Questions about the Pepperl+Fuchs KFD2-SCD-Ex1.LK SMART Current Driver,

Answers from our engineering team on installation, compatibility and integration.

01What does the KFD2-SCD-Ex1.LK do?
It drives SMART I/P converters, electrical valves and positioners in hazardous areas and carries HART digital signals in both directions.
02What load can it drive?
The load range is 100 to 700 ohm with an output voltage of at least 14 V at 20 mA.
03Where is the HART resistor?
An internal 250 ohm resistor is available between terminals 8 and 9 for use as the HART communication resistor.
04What supply does the KFD2-SCD-Ex1.LK need?
It uses 20 to 35 V DC from the Power Rail or terminals 11+ and 12-.
05How do I order the KFD2-SCD-Ex1.LK?
Send an RFQ with the part number KFD2-SCD-Ex1.LK, the quantity and the delivery location, and Seven Star LLC will reply with availability and lead time.