Schneider Electric ZB4BD3 Selector Switch Head 3-Pos Stay Put

ZB4BD3: Harmony XB4 selector switch head overview

The ZB4BD3 is a Schneider Electric Harmony XB4 head for a selector switch, listed with a black standard handle and 3 positions +/- 45°. It is a chromium plated metal head for a 22.5 mm panel hole; the electrical contacts are separate blocks that clip onto the rear. Seven Star LLC supplies the ZB4BD3 in Oman and the GCC as an independent supplier based in Muscat, typically for panel builders and maintenance teams who need a like-for-like replacement or an addition to an existing control station.

The datasheet short name for the range is ZB4, and this unit is sold as a single piece. A stay-put operator keeps the handle where the operator leaves it. Each position is a detent, and the handle does not move back by itself when released, so the selected state is held mechanically until someone turns the handle again.

Information to send with an RFQ for ZB4BD3

Please send the details below so that we can confirm the part number against its datasheet.

• Part number ZB4BD3 and quantity.
• Return behaviour needed: stay put, centre return, or left or right return.
• Handle length and colour, and whether padlocking is required.
• Number and type of contact blocks you plan to fit behind the head.
• Panel cut-out size and material.
• Approvals required for the project, to compare with the datasheet listing.
• Delivery location in Oman or the GCC and lead time.

If you are replacing a head, a photo of the old head and its rear blocks helps to confirm that the replacement matches.

Environmental data and approvals for ZB4BD3

The datasheet lists degrees of protection IP67, IP69, IP69K under IEC 60529 and impact rating IK06, with the UL enclosure type given as 4X/13. Operating temperature is -40–70 °C and storage temperature -40–70 °C. Vibration resistance is 5 gn (f= 2…500 Hz) per IEC 60068-2-6 and shock resistance is 30 gn for 18 ms or 50 gn for 11 ms, half sine, per IEC 60068-2-27. The datasheet lists these certifications: CSA, DNV, BV, LROS (Lloyds register of shipping), UL listed. Standards named include IEC 60947-5-5, IEC 60947-1, UL 508, CSA C22.2 No 14, IEC 60947-5-4, IEC 60947-5-1.

The product environmental data section shows EU RoHS compliance and an average recycled plastic content of 66 per cent. Warranty is given as 18 months. A single-piece pack measures about 5 cm per side, and the bulk carton holds 250 pieces. Country of origin on the datasheet is France.

How the 3-position operator of ZB4BD3 behaves

A stay-put operator keeps the handle where the operator leaves it. Each position is a detent, and the handle does not move back by itself when released, so the selected state is held mechanically until someone turns the handle again. The handle on this unit is described as a black standard handle, and the positions are 3 positions ± 45°, meaning the handle sits centrally and rotates 45 degrees to either side. The mechanical durability quoted is 1000000 cycles.

The handle is the standard length, 29 mm overall, which keeps the head compact and the projection in front of the panel small. It is a good match for dense control stations where long levers could be knocked in passing.

Installation and maintenance of ZB4BD3

Drill the panel to 22.5 mm and fit the head from the front, then clamp it with the collar or fixing blocks from the rear. Because the head carries no contacts, fit the contact or lamp blocks on the back only after the head is secured, and keep conductor ends clear of moving parts. Fit and torque the retaining parts as the datasheet’s mounting drawing shows; the drawing page gives the cut-out and clearance for the fitting.

During commissioning, operate this unit through its full range, check each contact state with a meter and confirm that the legend plate matches the function. In service, wipe the bezel clean, check seals during shutdowns, and replace any head that is cracked, loose or sticking. Keep a spare head in the maintenance store for panels that cannot be taken offline.

Typical uses of ZB4BD3 in Oman and the GCC

Selector heads of this style choose between modes on pumps, fans, compressors, valves and conveyors: hand-off-auto, local-remote, run-standby or duty selection. In oil and gas, petrochemical and power sites they appear on local control stations and motor control centre doors. In desalination and water plants they select between duty and standby pumps. Panels in Oman and the GCC see high ambient temperature, dust, wash-down on offshore and coastal sites and humidity from sea air, so the ingress rating of the head matters as much as its electrical function.

How ZB4BD3 fits the ZB4 head system

A complete station built around this unit has three parts: the head, a fixing and contact assembly on the back, and a legend plate or marking on the front. The Harmony XB4 range sells heads and blocks as separate items, which lets a panel builder keep one stock of blocks and choose the face of each control later. Because the ZB4BD3 is sold as a head only, always confirm the block part numbers and their voltage and current ratings for your circuit from the matching datasheets.

When the control scheme is reviewed, the head, the legend and the rear blocks should be documented together, since a panel that is modified later is much easier to maintain when each station can be identified by its head part number. For spares, hold a few heads of each type rather than whole stations, because the heads are the parts most exposed to knocks, sun and cleaning chemicals.

Technical specifications of the ZB4BD3

Choosing ZB4BD3 against its neighbours

For a three-position head the first decision is the return behaviour, because it decides how the control logic is wired. ZB4BD3 is the stay put version. Compare it with the siblings in the lane below, then check the contact block codes in the datasheet: it lists electrical composition codes (C3 to C11) that state how many single or double contact blocks can be combined behind the head in front mounting.

Documents and quotation

The Schneider Electric datasheet for the ZB4BD3, dated 8 Nov 2026, is attached on this page for your technical file. It lists the characteristics, environmental data and dimension drawings summarised above.

To request a quotation, send the part number and quantity through the enquiry form and we will reply with availability and delivery terms. Seven Star LLC is an independent supplier and does not act for the manufacturer, so please confirm that the datasheet data suits your project before ordering.