Brand:

LESER High Pressure Series – Type 455/456 and 457/458 Safety Valves

Description

Overview

The LESER High Pressure Series groups together LESER’s full-nozzle safety valve types built specifically for the upper end of the pressure spectrum within the wider High Performance product platform: the Type 455/456 and the Type 457/458. Where the standard rolled-in-seat Type 441/442 line is optimized for general industrial pressure ranges, these two types share a full-nozzle, welded-in-seat construction engineered to hold set-pressure accuracy and seat integrity at pressures up to 300 bar — a critical distinction for process engineers specifying safety relief on high-pressure separators, gas compression trains, and steam generation equipment.

With engineering support in Muscat, Seven Star LLC supplies the High Pressure line on request to refineries, gas processing plants, and power generation facilities throughout Oman and the wider GCC, with manufacturer documentation and local technical guidance.

Operating Principle

Both types in this line are direct-acting, spring-loaded, full-lift safety valves with a nozzle-type seat rather than the rolled-in seat used on the standard-pressure Type 441/442 line. In a full-nozzle design, the seat ring is machined into (or permanently fitted within) a separate nozzle insert that is isolated from the body casting, so the seating surface is not subject to the same thermal and mechanical stress the body itself experiences under high system pressure. This isolation is what allows the Type 455/456 and Type 457/458 to hold tight, repeatable set-pressure tolerances at pressures where a standard rolled-in-seat design would be more prone to seat drift over repeated lift cycles.

Once system pressure exceeds the calibrated spring force, the disc lifts fully off the nozzle seat and discharges through the valve outlet, and the design gives a stable full-lift characteristic rather than a partial “simmer” lift, which matters directly for capacity-critical high-pressure relief scenarios where the full rated flow needs to be reached quickly and predictably. Both types are available with a metallic seat and sealing-plate or O-ring secondary seal options depending on the tightness requirement of the protected system.

Engineering Design of the LESER High Pressure Series

The Type 455/456 covers DN 25 to DN 100 (or NPS 1 to NPS 4 on ASME B16.5 flanges) with a set-pressure range of 2.5 to 100 bar and a temperature range of –85°C to 550°C on CE-certified units (–29°C to 538°C on ASME units), in orifice sizes F+ to N+. The Type 457/458 extends the same full-nozzle body concept to a wider DN 25 to DN 150 (NPS 1 to NPS 6) size range and a higher 2.5 to 300 bar set-pressure ceiling across the same temperature envelope, with orifice sizes E through Q. Both types are supplied in carbon steel (1.0619), high-temperature carbon steel (1.7357), and cast stainless steel (1.4581) body materials, with stainless steel bellows available where back-pressure compensation is required.

Because both types share the same full-nozzle architecture and body material options, a plant standardizing on the LESER High Pressure line can move between the Type 455/456 and Type 457/458 purely on the basis of required set pressure and flow capacity, without changing bellows configuration, seat material logic, or spare-parts strategy. This shared design lineage keeps maintenance procedures and technician training consistent across a plant’s full population of high-pressure safety valves.

Key Features

The LESER High Pressure line delivers the following strengths for demanding process safety applications:

  • Full-nozzle seat design isolates the seating surface from body stress, holding tighter set-pressure accuracy at high pressure than a rolled-in-seat design.
  • Type 457/458 reaches set pressures up to 300 bar, covering the most demanding relief duties within the High Performance product platform.
  • Wide temperature capability from –85°C to 550°C (CE) suits both cryogenic and high-temperature steam or process gas service.
  • DN 25–150 / NPS 1–6 size range on Type 457/458 covers everything from small high-pressure separators to larger process vessels.
  • Stainless steel bellows options are available on both types for services with variable or superimposed back pressure.
  • Body material choices spanning carbon steel, high-temperature carbon steel, and cast stainless steel match the valve to the protected system’s temperature and corrosivity.
  • Metallic seat with sealing-plate or O-ring secondary seal options let engineers tune tightness to the specific application.
  • Full-lift, stable-flow characteristic ensures rated capacity is reached predictably during a genuine overpressure event.

Industrial Applications

The LESER High Pressure Series is specified wherever process conditions exceed what a standard rolled-in-seat safety valve is designed to hold reliably — high-pressure gas compression trains, deep-well injection and gas-lift systems, steam generation packages, and high-pressure separator vessels found across upstream oil and gas facilities, gas processing plants, and refineries. These duties are common across Oman’s upstream and midstream oil and gas sector and the wider GCC’s petrochemical corridor.

Backed by manufacturer datasheet documentation, Seven Star LLC distributes the High Pressure line to EPC contractors, plant reliability teams, and process equipment fabricators across Muscat, the Sohar Freezone and industrial port, the Salalah Free Zone, and the wider Sultanate of Oman and GCC, ensuring every valve supplied carries part-number traceability, certification, and after-sales technical support from a locally based team.

Technical Specifications

The comparison below sets the two High Pressure types against each other by verified size, pressure, and temperature range:

Type Size Range Pressure Range Temperature Range Key Feature
Type 455/456 DN 25 – DN 100 / NPS 1 – 4 2.5 – 100 bar –85°C to 550°C (CE) Full-nozzle, orifice F+ to N+
Type 457/458 DN 25 – DN 150 / NPS 1 – 6 2.5 – 300 bar –85°C to 550°C (CE) Full-nozzle, orifice E to Q, highest pressure in the line

Request a Quote for 455/456

Seven Star LLC invites process engineers, EPC contractors, and procurement teams across Oman and the GCC to submit a formal RFQ for the LESER High Pressure Series, covering Type 455/456 and Type 457/458. Full technical datasheets and direct access to the Seven Star LLC instrumentation and valve division are available on request.

Also available: LESER Type 483 Clean Service Safety Valve

Datasheets & Documents
  • PDF Brochure LESER High Performance Series Catalog Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

LESER is the German safety valve manufacturer whose history goes back to 16 March 1818, when Georg Wittmann started a brass foundry in Hamburg. The company built its first safety valve for steam boilers in 1885 and has focused only on safety valves since the 1970s. Its production sites are in Hohenwestedt (Germany), Paithan (India) and Tianjin (China).

Seven Star LLC is an independent supplier in Muscat. We list LESER spring-loaded and pilot-operated safety valves and change-over valves, and supply them and their spare parts to refineries, gas plants, boiler houses and process plants in Oman and the GCC.

LESER company profile

Origins 16 March 1818, Hamburg: brass foundry founded by Georg Wittmann
Safety valves First safety valve for steam boilers in 1885; safety valves only since the 1970s
Production Hohenwestedt (Germany), Paithan (India), Tianjin (China)
Product families API, High Performance, Compact Performance, Critical Service, Clean Service, High Pressure, Modulate Action and pilot-operated safety valves, plus change-over valves

Milestones

  • 1818: Georg Wittmann founds a brass foundry in Hamburg on 16 March.
  • 1885: LESER makes its first safety valve for steam boilers.
  • 1970s: The company concentrates on safety valves only.
  • Today: Production in Hohenwestedt (Germany), Paithan (India) and Tianjin (China).

LESER products we list

Series Types Typical use
API series Type 526, 526 CC Refinery and petrochemical relief to API 526
High Performance 441/442 DIN, 441/442 ANSI, 444 Steam, gases and liquids in general process and boiler service
Compact Performance 437, 459, 462 Small threaded valves for compressors, vessels and utilities
Critical Service 447, 449 Toxic, corrosive or high-pressure media, and block-body designs
High Pressure 457/458 High-pressure gas and liquid systems
Clean Service 483, 488 Food, pharmaceutical and clean steam
Pilot-operated, Modulate Action 811, 821 Large capacities and operation close to set pressure
Change-over valves 310 Two safety valves in parallel, so one can be serviced while the other protects the system

A spring-loaded safety valve opens when the system pressure overcomes the spring force at the set pressure. A pilot-operated valve uses the system pressure itself to hold the main valve shut, so it stays tight much closer to the set pressure and suits large flows. Sizing follows the required relief capacity from the worst-case scenario. API 526 fixes the flange sizes and orifice letters (D to T), so an API valve with the same orifice can replace one from another maker.

Where LESER safety valves are used

In Oman and the GCC, LESER safety valves protect vessels, heat exchangers, compressors, pumps, steam boilers and pipelines in oil and gas, refining, LNG, petrochemical, power and desalination plants.

Ordering LESER safety valves: what we need

Send the LESER type and article number from the nameplate, or the data sheet with the medium, set pressure, relieving temperature, required capacity, back pressure, inlet and outlet sizes and pressure classes, and the materials. For spare parts, send the serial number of the valve.

Facts checked against LESER company history (200th anniversary, 2018), October 2026.

FAQ

Questions about the LESER High Pressure Series

Answers from our engineering team on installation, compatibility and integration.

01What is the difference between Type 455/456 and Type 457/458?
Both are full-nozzle safety valves sharing the same body material options, but Type 455/456 covers DN 25-100 up to 100 bar while Type 457/458 covers the wider DN 25-150 range up to 300 bar. Type 457/458 is the choice when the required set pressure exceeds 100 bar.
02Why use a full-nozzle design instead of a rolled-in seat at high pressure?
A full-nozzle design isolates the seat from the mechanical and thermal stress of the body casting, which helps the valve hold tighter, more repeatable set-pressure tolerances over many lift cycles at high pressure compared to a standard rolled-in-seat design.
03What materials are available for high-pressure gas or sour service?
Both types are offered in carbon steel (1.0619), high-temperature carbon steel (1.7357), and cast stainless steel (1.4581), with stainless steel bellows available where back-pressure compensation or corrosion resistance is required.
04What is the maximum set pressure available in this line?
The Type 457/458 reaches a set-pressure ceiling of 300 bar, the highest available within LESER’s High Performance full-nozzle product line.
05Is Seven Star LLC an experienced supply partner for LESER products?
Yes. Seven Star LLC is an experienced supplier of LESER safety valves in Oman and the GCC, supplying LESER product with full documentation and local technical support.