Brand:

Siemens 6EP1334-3BA10 SITOP PSU200M 24V/10A Power Supply

Description

6EP1334-3BA10: SITOP PSU200M 24 V / 10 A stabilized power supply, explained

The Siemens 6EP1334-3BA10 is a technology-class modular supply that accepts single-phase mains or two phase conductors of a three-phase system. It is the 24 V DC, 10 A version in the catalog. Rated 10 A, the PSU200M 10 A unit is the same 70 mm width as the 5 A model but weighs about 0.8 kg and delivers 240 W at 91 % efficiency. It offers Power Boost for brief overload and a switchable short-circuit response.

The article number is simply the catalog identifier for this rating of the SITOP PSU200M group; it does not describe the build in a way that can be decoded digit by digit without the manufacturer’s tables, so always quote the full number 6EP1334-3BA10 when ordering. Seven Star LLC supplies the 6EP1334-3BA10 in Oman and the GCC as an independent supplier in Muscat.

Technical specifications of the 6EP1334-3BA10

Parameter Specification
Manufacturer / part number Siemens / 6EP1334-3BA10
Product line SITOP PSU200M (SITOP modular line)
Rated output 24 V DC, 10 A
Input 1-phase 120 – 230 V or 2-phase 230 – 500 V AC, set with a selector switch (ranges 85 – 264 V / 176 – 550 V)
Input current 4.4 A at 120 V; 2.4 A at 230 V
Switch-on current limit (+25 °C) max. 35 A
Mains buffering at rated load min. 25 ms; at Vin = 120/230 V, typ. 150 ms at Vin = 400 V
Output voltage adjustment 24 – 28.8 V via potentiometer
Output tolerance (static) ±3 %
Residual ripple (peak-peak, max.) 50 mV
Efficiency at rated load, approx. 91 %
Power loss at rated load, approx. 24 W
Start-up delay, max. 1 s
Short-circuit / overload response Selectable: constant-current characteristic (approx. 12 A) or latching shutdown
Parallel operation for more power Yes; switchable
Signalling output Relay contact (normally open, 60 V DC/0.3 A) for the output-voltage-OK message
Protection class Class I
Approvals listed cULus listed (UL 508, CSA C22.2 No. 107.1); CB; marine approvals listed: GL, ABS
Hazardous-area listings IECEx / ATEX category 3G (Ex nA) and cCSAus Class I Div. 2 listings appear in the catalog for this series; confirm the marking and temperature class on the exact unit
Ambient temperature (operation) −25 – +70 °C, natural convection
Derating note (catalog) +60 – +70 °C: Derating 2%/K (at 120 V, 230 V) or 3.5%/K (at 400 V)
Humidity class Climate class 3K3, no condensation
EMC Emissions EN 55022 Class B; noise immunity EN 61000-6-2
Degree of protection IP20
Dimensions (W × H × D) 70 × 125 × 121 mm
Weight, approx. 0.8 kg
Mounting Snap-on to DIN rail EN 60715 35 × 7.5/15; side-by-side mounting permitted
MTBF at 40 °C 1 055 408 h (catalog value)

Values are taken from the manufacturer’s SITOP catalog (KT 10.1, 2016) and apply at rated input voltage and +25 °C unless stated otherwise; check the current data sheet of the exact unit before design freeze.

How the 6EP1334-3BA10 regulates and protects its 24 V output

The 6EP1334-3BA10 uses a switch-mode converter behind an ultra-wide input: 120 – 230 V single-phase or 230 – 500 V across two phase conductors, chosen with a selector switch. Mains buffering is 25 ms at 120/230 V and typically 150 ms at 400 V, which keeps the output up through short supply dips.

Overload behaviour is the main differentiator of the modular line: Power Boost supplies up to three times rated current for 25 ms to trip downstream breakers, the unit tolerates 150 % for brief periods, and the short-circuit response can be set to constant current or latching shutdown. Three LEDs show operating status.

Where the 6EP1334-3BA10 fits in the control system

In a typical cabinet the 6EP1334-3BA10 sits right behind the incoming breaker and feeds a 24 V distribution rail. Other members of the SITOP PSU200M group in the catalog are 6EP1333-3BA10; they share the same operating concept but differ in rated current, width and weight, so they are not interchangeable in a fixed layout without checking space and breaker coordination.

For this series the catalog lists the SITOP PSE201U buffer module 6EP1961-3BA01, the PSE202U redundancy modules (6EP1961-3BA21, 6EP1962-2BA00, 6EP1964-2BA00), the PSE200U selectivity modules in 3 A and 10 A versions and device labeling plates 3RT1900-1SB20.

As an independent supplier, Seven Star LLC can help you match the supply to the rest of the bill of materials, for example by checking that the redundancy or buffer module suits the output current, but the final electrical design remains with your engineering team.

Selection and ordering checklist for the 6EP1334-3BA10

  • Load current: add the continuous demand of all 24 V consumers and compare it with the 10 A rating of the 6EP1334-3BA10, leaving margin for inrush and future additions.
  • Mains: confirm that the site supply matches the input data (1-phase 120 – 230 V or 2-phase 230 – 500 V AC, set with a selector switch (ranges 85 – 264 V / 176 – 550 V)) and check the input current figures given in the specification table.
  • Cabinet temperature: the operating range is -25 – +70 °C and derating applies at the upper end; compare it with the worst-case temperature inside the enclosure.
  • Space: allow 70 mm width on the rail plus 125 mm of height and 121 mm of depth; vertical clearance for convection is required.
  • Protection: for 1-phase operation the catalog recommends a breaker from 6 A (C) or 10 A (B); for 2-phase operation a 2-pole connected breaker is required.
  • Signalling: decide whether the relay contact will be wired to your monitoring system.
  • Add-ons: decide early whether a redundancy, buffer or selectivity module is needed; the catalog lists compatible modules for the series.
  • Pick it for 24 V loads up to 10 A in systems where you want one device for 120/230 V single-phase and 230/400/500 V two-phase supplies; catalog derating above +60 °C is 2 % per kelvin at 120/230 V and 3.5 % per kelvin at 400 V.

Installation, commissioning and maintenance

Mount the 6EP1334-3BA10 on a 35 mm DIN rail; the housing needs no lateral clearance. Before energising, set the input selector to 1-phase (120 – 230 V) or 2-phase (230 – 500 V) and select the short-circuit mode.

After wiring L, N and PE, connect the output and the 24 V OK contact. Use the three LEDs to read the operating state during commissioning and maintenance.

Set the input selector and the short-circuit mode (constant current around 12 A or latching shutdown) before commissioning.

  • Inspect terminals for tightness and discolouration at each shutdown.
  • Clean dust from the vents with dry compressed air; do not block the convection path.
  • Compare the output voltage with the value recorded at commissioning.
  • Keep one spare of the same article number for critical cabinets, since lead times for individual SITOP models can vary.

Typical applications in Oman and the GCC

In Oman and the GCC, the 6EP1334-3BA10 is attractive for export-oriented skids and packaged equipment that must work on different supply systems, including 230 V single-phase and 400 V three-phase networks. The operating range (-25 – +70 °C) suits hot enclosures, and the optional coated-PCB variants listed in the catalog are intended for harsher atmospheres.

Typical applications are export machinery, mobile or rental skids and multi-site standard panels.

SITOP PSU200M group at a glance

The table lists the SITOP PSU200M versions found in the catalog so you can compare ratings and size before selecting the 6EP1334-3BA10.

Article number Output Width Weight Efficiency
6EP1333-3BA10 24 V / 5 A 70 mm 0.6 kg 88 %
6EP1334-3BA10 24 V / 10 A 70 mm 0.8 kg 91 %

Information to send with an RFQ for the 6EP1334-3BA10

  • Exact article number (6EP1334-3BA10) and quantity, including whether you need identical replacement or an equivalent.
  • Supply system at site: voltage, frequency and number of phases, plus whether a DC feed is possible.
  • Output requirement: voltage, continuous current, peak or inrush loads and the number of parallel units if redundancy is planned.
  • Ambient conditions inside the cabinet: maximum temperature, dust, humidity and any hazardous-area classification.
  • Required accessories, for example redundancy, buffer or selectivity modules, terminals or labeling plates.
  • Delivery location (Muscat or elsewhere in Oman or the GCC) and required delivery time.
  • Any document requirement such as a datasheet or manual in English.

Documents and quotation

The official Siemens SITOP PSU200M compact operating instructions (A5E42154138, 09.2017, multilingual including English) are attached on this page as a PDF and cover the Siemens 6EP1334-3BA10 order number. They show the terminal layout, the input voltage selection, the output voltage adjustment, the mounting position and clearances, the safety notes and the main technical data of the 5 A and 10 A units. Check the input voltage, the output current and the mounting space against your panel before ordering, then send us the quantity and the delivery location for a quotation.

Seven Star LLC is an independent supplier based in Muscat and is not affiliated with the manufacturer. To request a quotation for the 6EP1334-3BA10, send the information listed above through the request-for-quotation form or by email; we will reply with availability and lead time.

Other Models in the Siemens Sitop Psu200m Range

Seven Star LLC supplies models from the Siemens Sitop Psu200m range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Siemens 6EP1333-3BA10 SITOP PSU200M 24V/5A Power SupplyPower ModulesView details
Siemens 6EP1334-3BA10 SITOP PSU200M 24V/10A Power SupplyPower ModulesYou are viewing this model
Datasheets & Documents
  • PDF Datasheet Siemens SITOP PSU200M 24 V/5 A and 10 A Operating Instructions (PDF) Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Siemens is the German technology group whose industrial products include SIMATIC controllers and HMIs, SINAMICS drives, SIRIUS and SENTRON switching and protection devices, SIPROTEC protection relays, SITRANS process instruments, SCALANCE networks and process analysers. It was founded in Berlin on 12 October 1847 by Werner von Siemens and the precision mechanic Johann Georg Halske as Telegraphen-Bauanstalt von Siemens & Halske, to build Siemens's newly designed pointer telegraph. Siemens AG is headquartered in Munich and listed on the Frankfurt Stock Exchange; its energy business was spun off as Siemens Energy in 2020.

Siemens company profile

Founded 12 October 1847, Berlin, Germany, as Telegraphen-Bauanstalt von Siemens & Halske, with 10 employees
Founders Werner von Siemens (1816–1892) and Johann Georg Halske (1814–1890)
First product The pointer telegraph designed by Werner von Siemens
Headquarters Munich, Germany (Siemens AG)
Ownership Public company listed in Frankfurt; Siemens Energy (2020) and Siemens Healthineers are separately listed companies
Businesses acquired that appear in our range Moore Products (bought in 2000; APACS and QUADLOG control systems), Applied Automation (Maxum process gas chromatographs); small industrial gas turbines such as the SGT-300 came with Alstom's industrial turbine business in 2003
Product families SIMATIC S7 PLCs, ET 200 distributed I/O and HMI panels, TIA Portal software, SINAMICS drives, SIMOTICS motors, SIRIUS and SENTRON low voltage devices, SIVACON switchboards, SIPROTEC relays, SITRANS instruments, SCALANCE network components, building technology valves and sensors

Milestones

  • 1847: Siemens & Halske starts work in Berlin with 10 employees.
  • 1848: The company wins the contract for Europe's first long-distance telegraph line, Berlin to Frankfurt am Main.
  • 1856: 330 employees, two-thirds of them working on telegraph networks in Russia.
  • 1866: Werner von Siemens describes the dynamo-electric principle, the basis of the electric generator.
  • 1958 onwards: The SIMATIC name is used for Siemens industrial automation; S7 PLCs follow in the 1990s and S7-1500 in 2012.
  • 2020: Siemens Energy is spun off and listed separately.

Choosing Siemens automation products

A Siemens order number (MLFB) identifies the exact product: 6ES7 is SIMATIC automation, 6AV is HMI, 6GK is industrial communication, 6SL is SINAMICS drives, 3R is SIRIUS control and 5SY is SENTRON miniature circuit breakers. For PLCs, S7-1200 is the compact controller for small machines, S7-1500 is the current mid-to-high range controller, and S7-300 and S7-400 are older platforms still running in many plants; S7-300 is being phased out, so spares and migration to S7-1500 are common requests. When replacing a CPU or module, the full order number including the version digits matters, because firmware and hardware versions affect compatibility with the existing project.

Where Siemens products are used

In Oman and the GCC, Siemens automation runs in oil and gas, power and desalination plants, water networks, cement and process industries. Maxum gas chromatographs analyse gas composition in gas plants and refineries, SIPROTEC relays protect substations, SGT-300 turbines drive generators and compressors, and Siemens building valves are used in HVAC systems.

Siemens products we list

Family Examples
SIMATIC controllers and I/O S7-1500, CPU 1515-2 PN, S7-1200, CPU 1214C, S7-300, S7-400H CPU 412-5H, ET 200SP, IM 153-2
HMI and networking KTP700 Basic, TP700 Comfort, TP1200 Comfort, SCALANCE XC208, SCALANCE WAM766, PROFIBUS OLM
Drives, motors and power distribution SINAMICS G120C, SINAMICS G120X, 1LA7 motor, SIVACON S8, SIPROTEC 7SJ85, 5SY4510-7 MCB
Process instruments SITRANS P320, MAG 5100W, SITRANS TH320, SITRANS TS500, SITRANS TR200
Maxum II analyser spares FID 302A detector, FPD II assembly, filament detector, Model 50 valve, SYSCON kit, air bath heater
APACS and QUADLOG spares QLCCM24AAN, QLSAMBAN, QLSDM024DCCBN, 39SAMCAN, 16137-151 M-BUS cable
Building technology VPI46 PICV, VPF44, QFM1660 sensor

Ordering Siemens products: what we need

Send the full order number from the label (for example 6ES7214-1AG40-0XB0) and, for PLC and HMI parts, the hardware and firmware version (FS and V numbers). For Maxum II and APACS spares, send the Siemens part number such as 2021651-002. For drives, add the motor power and supply voltage.

Frequently requested Siemens models: Siemens IM 155-6 PN ST ET 200SP Interface Module 6ES7155-6AU02-0BN0, Siemens SGT-300 Industrial Gas Turbine.

Facts checked against Siemens's published history timeline, October 2026.

FAQ

Questions about the Siemens 6EP1334-3BA10 SITOP PSU200M 24V/10A Power

Answers from our engineering team on installation, compatibility and integration.

01Can the 6EP1334-3BA10 run from two phases of a three-phase system?
Yes. The ultra-wide input allows single-phase operation at 120 – 230 V or two-phase operation at 230 – 500 V, selected with a switch. For two-phase operation a 2-pole connected breaker is required by the catalog.
02How much input current does the 6EP1334-3BA10 draw?
The catalog gives 4.4 A at the lower rated voltage and 2.4 A at the higher one, with a switch-on current limit of up to 35 A. Coordinate the upstream breaker with these values, especially when several units start together.
03How does the 6EP1334-3BA10 behave on a short circuit or overload?
The response is: selectable: constant-current characteristic (approx. 12 A) or latching shutdown. Make sure downstream protective devices can operate with this current, and confirm that the load list does not exceed the 10 A rating for long periods.
04Can the 6EP1334-3BA10 be connected in parallel?
Yes. The catalog allows parallel connection to increase power with up to 2 units (note: switchable). For redundancy rather than more power, the SITOP PSE202U redundancy modules decouple the supplies; match the module rating to the output current before ordering.
05What ambient temperature range does the 6EP1334-3BA10 support?
The catalog gives an operating range of -25 – +70 °C with natural convection. Derating applies at the upper end, so verify the cabinet temperature under full load rather than the room temperature.