Brand:

Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity Sensor

Description

At just 4 mm in diameter, the Omron E2E-C04S12-WC-B1 2M is among the smallest cylindrical inductive proximity sensors in the E2E range. It is made for places where a standard M8 or M12 sensor will not fit: tiny cylinders, miniature slides, electronics tooling and compact test fixtures.

The code reads: E2E series, C04 for a 4 mm smooth round body, S12 for shielded type with a 1.2 mm range, WC for a 2 m pre-wired PVC cable, B1 for PNP normally open, and 2M for the cable length. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. All data below are taken from the manufacturer small-diameter E2E datasheet.

Size, range and speed of E2E-C04S12-WC-B1 2M

Small does not mean slow. The 4 mm shielded body is rated at 4 kHz response frequency, the same as the M5 and 5.4 mm shielded types, although the 3 mm size E2E-C03SR8 goes higher at 5 kHz. The sensing distance is 1.2 mm plus or minus 10 percent, with a setting distance of 0 to 0.84 mm. The standard sensing object is iron, 4 by 4 by 1 mm, and differential travel is 15 percent or less.

Because the sensor is shielded, you can recess it into a metal block without the surrounding metal changing the switching distance. Four indicator lamps are placed around the circumference so the state can be seen from any angle, which matters on a 4 mm body that is often hidden inside a machine.

Specifications of E2E-C04S12-WC-B1 2M

Parameter Value
Model E2E-C04S12-WC-B1 2M
Body 4 mm diameter, shielded, smooth barrel
Sensing distance 1.2 mm plus or minus 10 percent
Setting distance 0 to 0.84 mm
Detectable object Ferrous metal
Standard sensing object Iron, 4 x 4 x 1 mm
Response frequency 4 kHz
Supply voltage 10 to 30 V DC including 10 percent ripple
Consumption 10 mA max.
Output PNP open collector, NO (B1)
Load current 100 mA max.
Residual voltage 2 V max.
Indicator Yellow operation lamp (EN 60947-5-2)
Protection Reverse polarity (supply and output), surge suppressor, short circuit
Ambient temperature Minus 25 to 70 degrees Celsius
Insulation resistance 50 megohm min. at 500 V DC
Degree of protection IP67, oil resistant
Case SUS303 stainless steel
Cable PVC, oil resistant, 2 m
Weight, pre-wired Approx. 35 g

How E2E-C04S12-WC-B1 2M differs from other 4 mm and small E2E sensors

Three numbers separate the neighbours in this family. The unshielded 4 mm E2E-C04N03 reaches 3 mm but needs free space in front and responds at only 2 kHz. The 3 mm E2E-C03SR8 senses at 0.8 mm but runs at 5 kHz. The 6.5 mm E2E-C06S02 senses 2 mm at 3 kHz. So the E2E-C04S12 is the choice when the body must be 4 mm, flush mountable and still reach more than 1 mm.

The output suffix also separates parts: -B1 here is PNP normally open, -B2 is PNP normally closed, -C1 and -C2 are the NPN types. Connector alternatives exist for this size too: CJ with a 0.3 m M8 pre-wired connector and MC with an M8 connector body, but a 4 mm sensor with a cable is the simplest form.

Use cases

  • Detecting the position of the miniature piston rods on 4 mm and 6 mm cylinders.
  • Verifying a metal pin or terminal is present in an electronics assembly jig.
  • Sensing the home position of small linear slides in laboratory and test equipment.
  • Counting small ferrous parts passing through narrow guides.

Mounting and handling notes for E2E-C04S12-WC-B1 2M

With no thread, the body is held by a clamp or a press-fit bore, so mounting distance is set by the fixture. Keep the cable strain relieved near the body and avoid sharp bends. The datasheet also lists robot (bending-resistant) cable versions with an R in the model code and 5 m cable versions with a 5M suffix for longer runs; these variants are different part numbers from this 2 m standard cable type.

Connect brown to a supply of 10 to 30 V DC, blue to 0 V, and black to the input. A 12 V supply with a load of 20 mA or less gives the most stable repeat accuracy because internal heating is lower, as the datasheet footnote explains.

Electrical protection built into E2E-C04S12-WC-B1 2M

The sensor includes four protective functions listed in the datasheet: reverse connection of the power supply, reverse connection of the output, a surge suppressor on the output, and load short-circuit protection. For a sensor this small, protection is valuable because wiring errors on a compact machine are common and a burnt 4 mm sensor is hard to replace in place. Current consumption is only 10 mA, about two thirds of earlier models according to the manufacturer, so a bank of these sensors adds little load to a 24 V supply. The output sources up to 100 mA, so a small interposing relay or a PLC input at 5 to 10 mA is easily driven. Insulation resistance of 50 megohm or more and a dielectric strength of 500 V AC for one minute are specified between the live parts and the case, which should be considered when the sensor is installed in a body that is grounded.

Maintenance

Wipe swarf from the sensing face, check the cable and the clamp at scheduled stops, and re-verify the setting distance after any machine adjustment. Replace the sensor if the output chatters when the cable is moved.

Documents and quotation

The manufacturer datasheet is attached to this page. Please send an RFQ with the part number E2E-C04S12-WC-B1 2M, quantity and delivery location in Oman or the GCC.

Spares and Lifecycle Considerations

For critical service, many plants hold one Omron E2E-C04S12-WC-B1 2M as an operational spare rather than waiting for a failure. When you plan spares, look at how many identical inductive proximity sensors units are installed, how long a replacement would take to arrive, and the cost of an unplanned stop. Store spare units in their original packaging in a dry, temperature-controlled area and record the part number and serial number in your maintenance system. We can quote single units or a small spares package and confirm the lead time for each item in writing.

Other Models in the Omron E2e Small Range

Seven Star LLC supplies models from the Omron E2e Small range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Omron E2E-C06S02-WC-B1 2M 6.5 mm Proximity SensorInductive Proximity SensorsView details
Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity SensorInductive Proximity SensorsYou are viewing this model
Datasheets & Documents
  • PDF Datasheet Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity Sensor Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Omron is a Japanese electronics and automation company, founded in 1933 in Osaka by Kazuma Tateisi and now headquartered in Kyoto. Its industrial automation business makes PLCs, I/O, sensors, relays, safety components, motion control and robots. Omron's CJ and NX series controllers and I/O units are widely used in machine building.

Seven Star LLC lists Omron PLC input and output units from the CJ and NX series and supplies them to panel builders and maintenance teams in Oman.

Omron company profile

Founded 1933, Osaka, Japan
Founder Kazuma Tateisi
Headquarters Kyoto, Japan
Business Industrial automation, healthcare, electronic components
Product families CJ1/CJ2 PLCs and I/O units, NX and NJ controllers, NX I/O, E2E proximity sensors, G2R and MY relays

Omron CJ-series and NX-series units listed here

Three I/O units are on this page. The CJ1W-ID211 is a CJ-series 16-point 24 VDC input unit and the CJ1W-OC211 is a CJ-series 16-point relay output unit. The NX-ID5442 is an NX-series 16-point 24 VDC digital input unit for PNP wiring, 12 mm wide with push-in terminals. CJ and NX units belong to different hardware platforms and do not plug into each other's racks.

Omron products we list

Family Examples
PLC & I/O Cards CJ1W-ID211 CJ-Series 16-Point 24 VDC Inp…, CJ1W-OC211 CJ-Series 16-Point Relay Outp…, NX-ID5442 NX-Series 16-Point Digital Inp…

Ordering Omron PLC modules: what we need

Send the complete model number from the front or side label of the unit, including every suffix. If you are replacing a failed card, add the CPU or coupler model it is mounted with, and tell us if the terminal block or connector is needed as well. For obsolete Omron PLC parts we check which successor the manufacturer documents. Requests from other GCC countries are handled the same way.

Facts checked against Omron's published company history, October 2026.

FAQ

Questions about the Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity

Answers from our engineering team on installation, compatibility and integration.

01What body size is the E2E-C04S12-WC-B1 2M?
It is a 4 mm diameter smooth-barrel shielded inductive sensor in SUS303 stainless steel, with a heat-resistant ABS sensing face.
02What is its sensing distance?
The rated sensing distance is 1.2 mm plus or minus 10 percent, with a recommended setting distance of 0 to 0.84 mm.
03How does it differ from the E2E-C04N03?
The C04N03 is unshielded with a 3 mm range and 2 kHz response, while the C04S12 is shielded with 1.2 mm range and 4 kHz response.
04Is it PNP or NPN?
The B1 code indicates PNP open collector, normally open. The NPN normally open version is E2E-C04S12-WC-C1.
05What is the maximum load current?
The 4 mm size is rated for a load current of 100 mA maximum, with a 2 V maximum residual voltage.