- Automation & ControlView all 2,859 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- Pneumatic Cylinders
- HMI Displays
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Omron
Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity Sensor
Description
At just 4 mm in diameter, the Omron E2E-C04S12-WC-B1 2M is among the smallest cylindrical inductive proximity sensors in the E2E range. It is made for places where a standard M8 or M12 sensor will not fit: tiny cylinders, miniature slides, electronics tooling and compact test fixtures.
The code reads: E2E series, C04 for a 4 mm smooth round body, S12 for shielded type with a 1.2 mm range, WC for a 2 m pre-wired PVC cable, B1 for PNP normally open, and 2M for the cable length. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. All data below are taken from the manufacturer small-diameter E2E datasheet.
Size, range and speed of E2E-C04S12-WC-B1 2M
Small does not mean slow. The 4 mm shielded body is rated at 4 kHz response frequency, the same as the M5 and 5.4 mm shielded types, although the 3 mm size E2E-C03SR8 goes higher at 5 kHz. The sensing distance is 1.2 mm plus or minus 10 percent, with a setting distance of 0 to 0.84 mm. The standard sensing object is iron, 4 by 4 by 1 mm, and differential travel is 15 percent or less.
Because the sensor is shielded, you can recess it into a metal block without the surrounding metal changing the switching distance. Four indicator lamps are placed around the circumference so the state can be seen from any angle, which matters on a 4 mm body that is often hidden inside a machine.
Specifications of E2E-C04S12-WC-B1 2M
| Parameter | Value |
|---|---|
| Model | E2E-C04S12-WC-B1 2M |
| Body | 4 mm diameter, shielded, smooth barrel |
| Sensing distance | 1.2 mm plus or minus 10 percent |
| Setting distance | 0 to 0.84 mm |
| Detectable object | Ferrous metal |
| Standard sensing object | Iron, 4 x 4 x 1 mm |
| Response frequency | 4 kHz |
| Supply voltage | 10 to 30 V DC including 10 percent ripple |
| Consumption | 10 mA max. |
| Output | PNP open collector, NO (B1) |
| Load current | 100 mA max. |
| Residual voltage | 2 V max. |
| Indicator | Yellow operation lamp (EN 60947-5-2) |
| Protection | Reverse polarity (supply and output), surge suppressor, short circuit |
| Ambient temperature | Minus 25 to 70 degrees Celsius |
| Insulation resistance | 50 megohm min. at 500 V DC |
| Degree of protection | IP67, oil resistant |
| Case | SUS303 stainless steel |
| Cable | PVC, oil resistant, 2 m |
| Weight, pre-wired | Approx. 35 g |
How E2E-C04S12-WC-B1 2M differs from other 4 mm and small E2E sensors
Three numbers separate the neighbours in this family. The unshielded 4 mm E2E-C04N03 reaches 3 mm but needs free space in front and responds at only 2 kHz. The 3 mm E2E-C03SR8 senses at 0.8 mm but runs at 5 kHz. The 6.5 mm E2E-C06S02 senses 2 mm at 3 kHz. So the E2E-C04S12 is the choice when the body must be 4 mm, flush mountable and still reach more than 1 mm.
The output suffix also separates parts: -B1 here is PNP normally open, -B2 is PNP normally closed, -C1 and -C2 are the NPN types. Connector alternatives exist for this size too: CJ with a 0.3 m M8 pre-wired connector and MC with an M8 connector body, but a 4 mm sensor with a cable is the simplest form.
Use cases
- Detecting the position of the miniature piston rods on 4 mm and 6 mm cylinders.
- Verifying a metal pin or terminal is present in an electronics assembly jig.
- Sensing the home position of small linear slides in laboratory and test equipment.
- Counting small ferrous parts passing through narrow guides.
Mounting and handling notes for E2E-C04S12-WC-B1 2M
With no thread, the body is held by a clamp or a press-fit bore, so mounting distance is set by the fixture. Keep the cable strain relieved near the body and avoid sharp bends. The datasheet also lists robot (bending-resistant) cable versions with an R in the model code and 5 m cable versions with a 5M suffix for longer runs; these variants are different part numbers from this 2 m standard cable type.
Connect brown to a supply of 10 to 30 V DC, blue to 0 V, and black to the input. A 12 V supply with a load of 20 mA or less gives the most stable repeat accuracy because internal heating is lower, as the datasheet footnote explains.
Electrical protection built into E2E-C04S12-WC-B1 2M
The sensor includes four protective functions listed in the datasheet: reverse connection of the power supply, reverse connection of the output, a surge suppressor on the output, and load short-circuit protection. For a sensor this small, protection is valuable because wiring errors on a compact machine are common and a burnt 4 mm sensor is hard to replace in place. Current consumption is only 10 mA, about two thirds of earlier models according to the manufacturer, so a bank of these sensors adds little load to a 24 V supply. The output sources up to 100 mA, so a small interposing relay or a PLC input at 5 to 10 mA is easily driven. Insulation resistance of 50 megohm or more and a dielectric strength of 500 V AC for one minute are specified between the live parts and the case, which should be considered when the sensor is installed in a body that is grounded.
Maintenance
Wipe swarf from the sensing face, check the cable and the clamp at scheduled stops, and re-verify the setting distance after any machine adjustment. Replace the sensor if the output chatters when the cable is moved.
Documents and quotation
The manufacturer datasheet is attached to this page. Please send an RFQ with the part number E2E-C04S12-WC-B1 2M, quantity and delivery location in Oman or the GCC.
Spares and Lifecycle Considerations
For critical service, many plants hold one Omron E2E-C04S12-WC-B1 2M as an operational spare rather than waiting for a failure. When you plan spares, look at how many identical inductive proximity sensors units are installed, how long a replacement would take to arrive, and the cost of an unplanned stop. Store spare units in their original packaging in a dry, temperature-controlled area and record the part number and serial number in your maintenance system. We can quote single units or a small spares package and confirm the lead time for each item in writing.
Other Models in the Omron E2e Small Range
Seven Star LLC supplies models from the Omron E2e Small range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Omron E2E-C06S02-WC-B1 2M 6.5 mm Proximity Sensor | Inductive Proximity Sensors | View details |
| Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity Sensor | Inductive Proximity Sensors | You are viewing this model |
Datasheets & Documents
- Datasheet Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity Sensor Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Omron is a Japanese electronics and automation company, founded in 1933 in Osaka by Kazuma Tateisi and now headquartered in Kyoto. Its industrial automation business makes PLCs, I/O, sensors, relays, safety components, motion control and robots. Omron's CJ and NX series controllers and I/O units are widely used in machine building.
Seven Star LLC lists Omron PLC input and output units from the CJ and NX series and supplies them to panel builders and maintenance teams in Oman.
Omron company profile
| Founded | 1933, Osaka, Japan |
|---|---|
| Founder | Kazuma Tateisi |
| Headquarters | Kyoto, Japan |
| Business | Industrial automation, healthcare, electronic components |
| Product families | CJ1/CJ2 PLCs and I/O units, NX and NJ controllers, NX I/O, E2E proximity sensors, G2R and MY relays |
Omron CJ-series and NX-series units listed here
Three I/O units are on this page. The CJ1W-ID211 is a CJ-series 16-point 24 VDC input unit and the CJ1W-OC211 is a CJ-series 16-point relay output unit. The NX-ID5442 is an NX-series 16-point 24 VDC digital input unit for PNP wiring, 12 mm wide with push-in terminals. CJ and NX units belong to different hardware platforms and do not plug into each other's racks.
Omron products we list
| Family | Examples |
|---|---|
| PLC & I/O Cards | CJ1W-ID211 CJ-Series 16-Point 24 VDC Inp…, CJ1W-OC211 CJ-Series 16-Point Relay Outp…, NX-ID5442 NX-Series 16-Point Digital Inp… |
Ordering Omron PLC modules: what we need
Send the complete model number from the front or side label of the unit, including every suffix. If you are replacing a failed card, add the CPU or coupler model it is mounted with, and tell us if the terminal block or connector is needed as well. For obsolete Omron PLC parts we check which successor the manufacturer documents. Requests from other GCC countries are handled the same way.
Facts checked against Omron's published company history, October 2026.
FAQ
Questions about the Omron E2E-C04S12-WC-B1 2M 4 mm Inductive Proximity
Answers from our engineering team on installation, compatibility and integration.
01What body size is the E2E-C04S12-WC-B1 2M?
It is a 4 mm diameter smooth-barrel shielded inductive sensor in SUS303 stainless steel, with a heat-resistant ABS sensing face.
02What is its sensing distance?
The rated sensing distance is 1.2 mm plus or minus 10 percent, with a recommended setting distance of 0 to 0.84 mm.
03How does it differ from the E2E-C04N03?
The C04N03 is unshielded with a 3 mm range and 2 kHz response, while the C04S12 is shielded with 1.2 mm range and 4 kHz response.
04Is it PNP or NPN?
The B1 code indicates PNP open collector, normally open. The NPN normally open version is E2E-C04S12-WC-C1.
05What is the maximum load current?
The 4 mm size is rated for a load current of 100 mA maximum, with a 2 V maximum residual voltage.


















Reviews
There are no reviews yet.