Phoenix Contact TRIO-PS-2G/3AC/24DC/40 Power Supply 40 A

TRIO-PS-2G/3AC/24DC/40: three-phase 24 V DC 40 A supply, 960 W with dynamic boost

The Phoenix Contact TRIO-PS-2G/3AC/24DC/40 (order no. 2903156) is the largest model in this TRIO 2G selection: 24 V DC at 40 A, 960 W, from a three-phase input. It is 110 mm wide, 130 mm high and 160 mm deep and uses tool-free connection technology for solid and ferruled conductors.

Seven Star LLC supplies the TRIO-PS-2G/3AC/24DC/40 as an independent supplier in Muscat for projects in Oman and the GCC, quoted against the exact part number shown here.

Technical specifications of the TRIO-PS-2G/3AC/24DC/40

How the TRIO-PS-2G/3AC/24DC/40 works

The TRIO-PS-2G/3AC/24DC/40 is a primary-switched supply from the TRIO POWER 2nd generation (the 2G in the type code). Mains input is converted to an isolated, regulated DC output through a high-frequency stage. The datasheet lists a dynamic boost, an output power figure that can be drawn for a few seconds above nominal, which helps with start-up peaks of motors, solenoids and capacitive loads. A DC OK signal on a changeover contact and an LED report the status of the output, so a controller can see when the supply is healthy.

Dynamic boost gives 1440 W for 5 seconds, and the typical efficiency is 92.6 % at 400 V AC and 480 V AC. Because of its size and capacity, it typically feeds a whole cabinet through an electronic circuit breaker or fuse distribution.

Where the TRIO-PS-2G/3AC/24DC/40 fits in a system

TRIO POWER sits between the compact STEP POWER range and the more advanced QUINT POWER range: it gives a robust metal-housing supply, wide temperature range down to -25 degrees C, and a status contact, without the NFC configuration and selective fuse breaking of QUINT4. It is a typical mid-range choice for machine builders and panel shops who want proven performance at moderate cost.

The TRIO-PS-2G/3AC/24DC/40 suits larger panels as the main 24 V source. If you want NFC configuration and selective fuse breaking at 40 A, compare with the QUINT4-PS/3AC/24DC/40/CO (1783052).

Selection and ordering checklist

• Confirm the nominal output voltage and current of the TRIO-PS-2G/3AC/24DC/40 against the load total, leaving a reserve.
• Check input voltage and number of phases against the site supply.
• Note the dynamic boost power if the loads have a start-up peak.
• Compare the housing width and depth with the available rail space and cabinet door clearance.
• Check that the ambient temperature does not exceed the derating limit of 60 degrees C for continuous full load.
• Decide whether the status contact will be wired to a controller.

Installation, commissioning and maintenance of the TRIO-PS-2G/3AC/24DC/40

Mount the TRIO-PS-2G/3AC/24DC/40 on a 35 mm DIN rail with the clearances shown on the datasheet, connect the input and output to the labelled terminals and fit the status wiring if it is needed. Set the output voltage with the potentiometer, check the polarity at the loads and confirm that the DC OK LED lights before closing the cabinet.

Take the output current rating from the table and apply the derating shown for temperatures above 60 degrees C. After commissioning, retighten terminals once the unit has seen a thermal cycle and keep the vents clear of dust.

Typical applications in Oman and the GCC

In Oman and the GCC, control cabinets often run at high ambient temperatures, so the operating range and derating curve in the table are what decide whether a supply is suitable. These supplies are used in oil and gas skids, water treatment and desalination plants, power substations, petrochemical packages and building automation panels.

Pump stations, compressors and larger packaged systems across the GCC use this class of supply.

Comparison with related TRIO POWER 2nd-generation devices

Information to send with an RFQ

• Full part number TRIO-PS-2G/3AC/24DC/40 and quantity.
• Mains supply voltage, phases and frequency at site.
• Total connected load and the largest single load current including inrush.
• Cabinet temperature at the hottest point and the mounting altitude.
• Whether redundancy, parallel operation or a monitoring signal is needed.
• Delivery location and required date.

Documents and quotation

Send us the part number TRIO-PS-2G/3AC/24DC/40 and the quantity you need, and we will confirm which official documents are available for this device. Seven Star LLC is an independent supplier in Muscat and quotes for projects across Oman and the GCC; we do not act on behalf of the manufacturer.

Please also tell us the delivery location and required timeline so that availability can be checked before you commit to a project schedule.