Brand:

Swagelok SS-SS4 S Series Low Flow Metering Valve, 1/4 in. Tube

Description

SS-SS4: fine flow control for very small flows

Swagelok SS-SS4 is an S series metering valve in 316 stainless steel with 1/4 in. Swagelok tube fitting ends, a knurled handle and a maximum Cv of just 0.004. It is built for setting very small, repeatable flows of gas or liquid in analyzer, chromatograph and purge applications, with a temperature range of minus 10 to 400 degrees F (minus 23 to 204 degrees C).

The catalog describes the S and M series as low-pressure metering valves with straight-pattern Cv from 0.004 to 0.03, forged-body 316 stainless or brass construction, and handles of knurled, round, vernier, slotted or adjustable-torque types.

Why the taper matters

The tapered stem tip of the metering valve accurately controls gas and liquid flow rates. The S series uses a 1 degree taper (the M series uses 3 degrees) on a 0.032 in. (0.81 mm) orifice. The slender angle means many handle turns translate into a small change in flow area, which is the property that allows fine setting. Stem threads are isolated from the system fluid by a stem O-ring, a guide O-ring improves stem alignment, and a handle stop helps prevent damage to the stem and orifice.

Remember that a metering valve is a control element and not a pressure regulator. Where the supply pressure varies, flow through SS-SS4 varies with it, so pair it with a regulator upstream if constant flow is needed.

The catalog lists no shutoff service for the S and M series, and it fits a handle stop to protect the stem and orifice from damage. That is why a separate isolation valve is specified wherever positive shutoff is needed.

Because Cv is so small, the valve is very sensitive to temperature changes in gas service; shield analyzer cabinets from direct sun so the flow setting stays stable throughout the day in hot Gulf conditions.

When replacing an old metering valve on an analyzer panel, confirm the series (S, M or 31), the handle type and the end connections from the string. For instance the final digit 4 in SS-SS4 indicates 1/4 in. tube ends; a different digit changes the connection size and may alter the plumbing layout.

Technicians should note the number of turns from the closed stop at the commissioning flow setting, which gives a repeatable reference after maintenance, even without a vernier handle.

In regard to chemical compatibility, the wetted parts are 316 stainless steel and fluorocarbon FKM O-rings; verify that the sample medium does not attack FKM, since amines and some ketones do. A different O-ring material changes the string and the temperature range.

For documentation, list the Cv value 0.004, the 0.032 in. orifice, the 2000 psig working pressure and the knurled handle against the item SS-SS4, so the instrument technician can check the valve against the analyzer manufacturer’s required flow setting.

Keep the valve closed against its handle stop only lightly when parking the setting, since over-tightening can damage the tapered tip.

SS-SS4 specification

Part number SS-SS4
Series S series low-flow metering valve
Body 316 stainless steel
Ends 1/4 in. Swagelok tube fitting x 2
Max Cv 0.004
Orifice 0.032 in. (0.81 mm)
Stem taper 1 degree
Handle Knurled
Working pressure Up to 2000 psig (137 bar) for the S series
O-rings Fluorocarbon FKM
Temperature range Minus 10 to 400 F (minus 23 to 204 C)
Cleaning SC-10

SS-SS4 versus needle valves and the M series

A needle valve such as SS-1RS4 has 0.37 Cv, about ninety times the capacity of SS-SS4, and is intended for larger flows. The M series metering valves have a 0.056 in. orifice, a 3 degree taper and a 1000 psig rating, so they handle somewhat larger flows. Choose SS-SS4 when the target flow is tiny, such as a few cubic centimetres per minute of sample gas.

Applications

Setting sample flow to analyzers and chromatographs, purge flows on optical instruments, carrier gas flow and small reagent additions. Utilities and oil and gas laboratories in the region use them in test rigs.

Installing and setting

Because the valve cannot shut off, add a separate isolation valve upstream. Set the flow using a rotameter or flow meter downstream, then tighten the lock screw so the setting is kept. Do not force the handle past the stop.

Care

Filter the fluid to protect the tiny orifice. Particles of even a few micrometres can disturb the setting. Avoid cleaning with sharp tools. If flow drifts, check for debris at the tapered tip.

Ordering

Quote SS-SS4 with quantity and note if you need a vernier handle for repeatable settings, which is a different part.

Quick answers about SS-SS4

What flow coefficient does Swagelok SS-SS4 have? The maximum Cv is 0.004, among the lowest in the metering valve range, intended for very small gas and liquid flows.

What temperature range does SS-SS4 cover? Minus 10 to 400 degrees F (minus 23 to 204 degrees C) as listed in the product data.

Can SS-SS4 be used for shutoff? No. The catalog states that the S and M series metering valves have no shutoff service, so a separate isolation valve is needed.

What is the stem taper of the S series? The S series uses a stem taper of 1 degree and an orifice of 0.032 in. (0.81 mm), with fluorocarbon FKM O-rings.

What handle does SS-SS4 have? A knurled handle with a lock screw that locks in the flow setting.

Documents and quotation

The datasheet is the manufacturer metering valve catalog for S, M and 31 series. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. Send the RFQ with SS-SS4, quantity and delivery location.

Ordering Checklist for the Swagelok SS-SS4

Before you ask for a quotation for the Swagelok SS-SS4, check the full order code on the nameplate of the unit you are replacing, the supply voltage, and the process or signal ranges your system expects. If this is an upgrade rather than a like-for-like swap, tell us the existing make and model so that mounting, wiring and connection details can be checked against the instrument valves & fittings already installed. For multi-unit orders, list the quantity per site and the delivery location in Oman or the wider GCC, so packing, paperwork and lead time can be confirmed in a single quotation.

Datasheets & Documents
  • PDF Datasheet Swagelok SS-SS4 S Series Low Flow Metering Valve, 1/4 in. Tube Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Swagelok is the American maker of tube fittings and small-bore valves, best known for its two-ferrule compression tube fitting. Fred A. Lennon and Cullen B. Crawford founded it in Cleveland, Ohio, in July 1947 as Crawford Fitting Company to make that fitting. Lennon bought the whole business and the patent in 1948, and the company has been based in Solon, Ohio, since the mid-1960s.

Seven Star LLC is an independent supplier in Muscat. We list Swagelok tube fittings, needle, ball, check, relief and metering valves, filters, regulators and sample cylinders, and supply them for instrument tubing and analyser systems in Oman and the GCC by exact part number.

Swagelok company profile

Established July 1947, Cleveland, Ohio, as Crawford Fitting Company
Founders Fred A. Lennon and Cullen B. Crawford; Lennon bought out Crawford in 1948
Headquarters Solon, Ohio, since the mid-1960s
Product families Tube fittings and adapters, face seal fittings, needle, ball, plug, check, relief and diaphragm valves, filters, regulators, quick-connects, sample cylinders and hoses

Milestones

  • 1947: Fred A. Lennon and Cullen B. Crawford found Crawford Fitting Company in Cleveland in July.
  • 1948: Lennon buys out Crawford.
  • Mid-1960s: Headquarters move to Solon, Ohio.

Swagelok products we list

Family Models Typical use
Tube fittings Overview, SS-810-6 union, SS-810-3 tee, SS-810-9 elbow, SS-810-4 cross, SS-810-1-8 male connector, SS-810-7-8 female connector, SS-810-61 bulkhead, SS-12M0-6 metric union, VCR face seal Leak-tight connections on instrument and process tubing
Needle and metering valves SS-1RS4, SS-1RF4, SS-18RF6, SS-6NBS6, SS-20VS4, SS-4MG Isolation and fine flow adjustment on instrument lines and sample systems
Ball and plug valves 40G, 40GX 3-way, 60 Series, 83 Series, P4T plug Quick quarter-turn shut-off and switching
Check, relief and sealed valves SS-4C-1, CH, R3A, RL3, SS-4BK bellows, SS-DLS4 diaphragm Backflow prevention, overpressure relief and leak-free sealing for toxic or high-purity media
Filters, regulators, sampling SS-4F-2, SS-4TF-7, KPR regulator, sample cylinders, QC quick-connects Analyser sample conditioning and gas or liquid sampling

A Swagelok part number can be read directly. In SS-810-6, "SS" is 316 stainless steel, "810" means a 1/2 in. tube fitting (8 sixteenths of an inch, 10 series), and "-6" is a union. A suffix such as "-8" adds a 1/2 in. NPT end, and "M0" marks metric tube, as in SS-12M0-6 for 12 mm. Tube fittings must be made up the same way every time: finger-tight, then 1 1/4 turns for most sizes. A gap inspection gauge confirms the fitting has been pulled up.

Where Swagelok products are used

In Oman and the GCC, Swagelok fittings and valves are used on instrument impulse lines, analyser sample systems, hydraulic and pneumatic control tubing, chemical injection and gas sampling in oil and gas, refining, petrochemical, power and laboratory installations.

Ordering Swagelok products: what we need

Send the full Swagelok part number (for example SS-810-6 or SS-1RS4), the material, and the tube size in inches or millimetres. For valves, add the end connections and any options. For sample cylinders, add the volume, pressure rating and end configuration.

Facts checked against Swagelok company history, October 2026.

FAQ

Questions about the Swagelok SS-SS4 S Series Low Flow Metering Valve,

Answers from our engineering team on installation, compatibility and integration.

01What flow coefficient does Swagelok SS-SS4 have?
The maximum Cv is 0.004, among the lowest in the metering valve range, intended for very small gas and liquid flows.
02What temperature range does SS-SS4 cover?
Minus 10 to 400 degrees F (minus 23 to 204 degrees C) as listed in the product data.
03Can SS-SS4 be used for shutoff?
No. The catalog states that the S and M series metering valves have no shutoff service, so a separate isolation valve is needed.
04What is the stem taper of the S series?
The S series uses a stem taper of 1 degree and an orifice of 0.032 in. (0.81 mm), with fluorocarbon FKM O-rings.
05What handle does SS-SS4 have?
A knurled handle with a lock screw that locks in the flow setting.