- Automation & ControlView all 2,466 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- CCTV & Security
- Motor Soft Starters
- Encoders
- Safety Switches & Guard Locking
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Festo
Festo QS-G1/8-6-I Push-in Fitting
Description
QS-G1/8-6-I: push-in fitting, G1/8 to 6 mm tube
The Festo QS-G1/8-6-I (article 186107) is the standard-size push-in fitting with a G1/8 male thread, internal hexagon and a 6 mm tubing connection. A push-in fitting joins plastic tubing to a threaded port without tools: the tube is pushed in until it locks and is released by pressing the ring. Seven Star LLC supplies QS-G1/8-6-I in Oman and the GCC as an independent supplier in Muscat, not affiliated with the manufacturer. The sections below translate the datasheet for selection and enquiry.
Reading the part number against the datasheet:
- QS is the push-in fitting family shown on the sheet (push-in fitting).
- Thread side: Male thread G1/8.
- Tube side: For tubing outside diameter of 6 mm.
- Nominal size 4.2 mm and a pack size of 10 on the datasheet.
- Release ring colour blue; mounting by internal hexagon A/F 4.
QS-G1/8-6-I technical specifications
Values below come from the manufacturer data sheet for article 186107.
| Parameter | Specification |
|---|---|
| Manufacturer / part number | Festo / QS-G1/8-6-I |
| Article number | 186107 |
| Size | Standard |
| Nominal size | 4.2 mm |
| Tubing insertion depth | 17 mm |
| Type of seal on screwed plug | Sealing ring |
| Mounting position | Any |
| Design | Straight design; Push-pull principle |
| Size of pack | 10 |
| Operating pressure complete temperature range | -0.095 MPa to 0.6 MPa; -0.95 bar to 6 bar; -13.775 psi to 87 psi |
| Temperature-dependent operating pressure | -0.095 MPa to 1.4 MPa; -0.95 bar to 14 bar; -13.775 psi to 203 psi |
| Note on operating pressure | Water: max. 0.6 MPa at max. 50°C |
| Operating medium | Compressed air to ISO 8573-1:2010 [7:-:-]; Water (liquid, ice-free) |
| Note on operating and pilot medium | Lubricated operation possible; Water: G-thread only possible with sealing ring type OL as additional; accessory |
| Corrosion resistance class CRC | 1 – Low corrosion stress |
| LABS (PWIS) conformity | VDMA24364-B1/B2-L |
| Cleanroom suitability, measured according to ISO 14644-14 | Class 4 according to ISO 14644-1 |
| Ambient temperature | -10 °C to 80 °C |
| Nominal torque | 5.4 Nm |
| Tolerance for nominal tightening torque | ±20% |
| Product weight | 8.3 g |
| Type of mounting | Internal hexagon A/F 4 |
| Pneumatic connection, port 1 | Male thread G1/8 |
| Pneumatic connection, port 2 | For tubing outside diameter of 6 mm |
| Colour of release ring | Blue |
| Material housing | Brass, nickel-plated |
| Material release ring | POM |
| Material tubing seal | NBR |
| Material tubing clamp component | High-alloy stainless steel |
How the QS-G1/8-6-I push-in connection works
Inside the fitting a stainless steel clamp ring grips the tube wall while a sealing element seals against its outside surface. Pushing the tube past the clamp locks it; pressing the release ring frees it again, so tubing can be changed in seconds. The listed insertion depth of 17 mm ensures the tube reaches the sealing zone.
The pressure window on the datasheet is -0.95 to 6 bar over the complete temperature range and -0.95 to 14 bar at moderate temperature. Check these values against the supply pressure, and remember that tubing, not only the fitting, defines the limit of a real installation.
The operating medium is Compressed air to ISO 8573-1:2010 [7:-:-]; the note allows lubricated operation. Water is also listed: Water: max. 0.6 MPa at max. 50°C.
Where QS-G1/8-6-I fits: compatible and related parts
A fitting like this sits at the end of a tube run on a valve, cylinder, regulator, manifold or sensor port. The thread must match the port exactly, and the tube outside diameter must match the push-in side; the sheet lists Male thread G1/8 and For tubing outside diameter of 6 mm.
Other push-in fittings we handle in this range include QS-V0-G1/4-8, QSR-G1/4-6, QSMK-G1/4-6, QS-1/4-12-I, QSM-G1/8-4, QS-1/4-6-I, QSF-1/4-6-B. They differ in thread, tube size, rotation, sealing and material, so they are not interchangeable without checking the port and tubing.
Selection and ordering checklist for QS-G1/8-6-I
- Thread: Male thread G1/8; confirm G (parallel) or R (tapered) against the mating port.
- Tube outside diameter: For tubing outside diameter of 6 mm and the tube material approved for this fitting.
- Pressure: -0.95 to 6 bar over the full temperature range on the datasheet.
- Ambient temperature on the sheet: -10 °C to 80 °C.
- Housing material: Brass, nickel-plated; weight 8.3 g.
- Note the G-thread water remark: the sheet says water use with a G thread is only possible with sealing ring type OL as an additional accessory. Check the cleanroom class 4 entry if the fitting is going into a clean area.
Installation, commissioning and maintenance of QS-G1/8-6-I
Cut the tube square with a proper tube cutter, push it fully home and give it a light pull to check the lock. The listed nominal tightening torque is 5.4 Nm. Use a spanner on the internal hexagon A/F 4 only, never on the tube side. Do not overtighten into a plastic port.
After fitting, pressurise slowly and check for leaks with a soap solution. During maintenance, replace fittings whose release ring is damaged or where the tube end shows scoring. Keep a stock of common sizes for fast repairs.
Typical applications of QS-G1/8-6-I in Oman and the GCC
Oman and the wider GCC put pneumatic and sensing equipment under demanding conditions: summer ambient heat, fine desert dust, high humidity in coastal plants and compressed-air systems that are not always perfectly dried. The G1/8 thread with a 6 mm tube is one of the most common combinations on small and medium pneumatic valves and cylinders. The internal hexagon allows the fitting to be tightened in tight spaces where a spanner would not fit.
The datasheet lists a corrosion resistance class of 1 – Low corrosion stress. For outdoor or coastal installations, keep tube runs short, avoid direct sun on plastic tubing and protect exposed fittings from sand with covers or enclosures.
QS-G1/8-6-I compared with other Festo push-in fittings
Thread, tube size, nominal size and weight from the manufacturer sheets of the fittings listed in this range.
| Part number | Thread | Tube | Nominal size | Weight |
|---|---|---|---|---|
| QS-G1/8-6-I | Male thread G1/8 | 6 mm | 4.2 mm | 8.3 g |
| QS-V0-G1/4-8 | Male thread G1/4 | 8 mm | 7 mm | 15 g |
| QSR-G1/4-6 | Male thread G1/4 | 6 mm | 3.4 mm | 25 g |
| QSMK-G1/4-6 | Male thread G1/4 | 6 mm | 3 mm | 26 g |
| QS-1/4-12-I | Male thread R1/4 | 12 mm | 6.3 mm | 29 g |
| QSM-G1/8-4 | Male thread G1/8 | 4 mm | 2.9 mm | 9.4 g |
| QS-1/4-6-I | Male thread R1/4 | 6 mm | 4.2 mm | 13 g |
| QSF-1/4-6-B | Female thread G1/4 | 6 mm | 5 mm | 23 g |
Information to send with your QS-G1/8-6-I RFQ
- Full part number QS-G1/8-6-I and quantity (the datasheet pack size is 10).
- Thread type and size on the mating port.
- Tubing material and outside diameter.
- Operating pressure, medium and temperature.
- Any flame, cleanroom or water-service requirement.
- Delivery location in Oman or the GCC.
Documents and quotation
The manufacturer data sheet for QS-G1/8-6-I is attached on this page for download.
Send the part number QS-G1/8-6-I with quantity and delivery location and we will confirm availability and a quotation. Seven Star LLC is an independent supplier and is not affiliated with the manufacturer.
Other Models in the Festo Push In Fittings Range
Seven Star LLC supplies models from the Festo Push In Fittings range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Festo QS-V0-G1/4-8 Push-in Fitting | Pipes & Fittings | View details |
| Festo QSR-G1/4-6 Push-in Fitting | Pipes & Fittings | View details |
| Festo QSMK-G1/4-6 Push-in Fitting | Pipes & Fittings | View details |
| Festo QS-1/4-12-I Push-in Fitting | Pipes & Fittings | View details |
| Festo QSM-G1/8-4 Push-in Fitting | Pipes & Fittings | View details |
| Festo QS-G1/8-6-I Push-in Fitting | Pipes & Fittings | You are viewing this model |
| Festo QS-1/4-6-I Push-in Fitting | Pipes & Fittings | View details |
| Festo QSF-1/4-6-B Push-in Fitting | Pipes & Fittings | View details |
Datasheets & Documents
- Datasheet Festo QS-G1/8-6-I Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Festo is a German maker of pneumatic and electric automation technology, founded in 1925 in Esslingen am Neckar by Albert Fezer and Gottlieb Stoll; the name comes from their surnames. It first made woodworking machines and power tools before moving into pneumatics in the 1950s. Festo is family-owned and still headquartered in Esslingen.
Seven Star LLC sources and supplies Festo cylinders, valves and valve terminals for machine maintenance and projects in Oman and the GCC.
Festo company profile
| Founded | 1925, Esslingen am Neckar, Germany |
|---|---|
| Founders | Albert Fezer and Gottlieb Stoll |
| Name | From FEzer and STOll |
| Headquarters | Esslingen am Neckar |
| Ownership | Family-owned |
| Product families | DSBC and ADN pneumatic cylinders, VUVG and VTUG solenoid valves and valve terminals, MS series air preparation units, CPX-AP remote I/O, EMMT servo motors and CMMT servo drives, electric axes and grippers |
Milestones
- 1925: Fezer and Stoll found the company in Esslingen.
- 1950s: Festo begins making pneumatic components.
Festo products listed
Two items show the two halves of a pneumatic circuit. The VTUG is a valve terminal: a manifold that carries a row of directional valves with common air supply and a shared electrical connection. The DSBC-32-100-PPVA-N3 is an ISO standard cylinder. Its type code reads as 32 mm piston diameter and 100 mm stroke, with adjustable end-position cushioning and a piston magnet for position sensing.
Festo products we list
Ordering Festo parts: what we need
Festo parts carry both a type code and a numeric part number on the label. Send both when you can; the part number is the shortest route to an exact match. For a cylinder give the full type code as on the listed DSBC example, plus mounting parts and proximity switches if required. For a VTUG valve terminal send the configuration code or a label photo: number of valve positions, valve functions, coil voltage and the electrical connection type all vary from one terminal to the next.
Facts checked against Festo's corporate history pages, October 2026.
Browse Festo products by category: Solenoid Valve, Valve Actuator.
FAQ
Questions about the Festo QS-G1/8-6-I Push-in Fitting
Answers from our engineering team on installation, compatibility and integration.
01What thread and tube size does the QS-G1/8-6-I have?
The datasheet lists Male thread G1/8 on the thread side and For tubing outside diameter of 6 mm on the tube side for article 186107.
02What pressure can the QS-G1/8-6-I be used at?
Over the full temperature range the datasheet gives -0.95 to 6 bar, and -0.95 to 14 bar at moderate temperature.
03What is the nominal size of the QS-G1/8-6-I?
The nominal size is 4.2 mm and the product weighs 8.3 g according to the data sheet.
04How is the QS-G1/8-6-I tightened?
Mounting is by internal hexagon A/F 4. The nominal tightening torque is 5.4 Nm.
05Can the QS-G1/8-6-I be used with water?
The datasheet lists liquid, ice-free water as a medium with the limit: Water: max. 0.6 MPa at max. 50°C.


















Reviews
There are no reviews yet.