Weidmuller PRO ECO 240W 24V 10A Power Supply

Weidmuller PRO ECO 240W 24V 10A switch-mode power supply, order no. 1469490000

1469490000 is the Weidmuller PRO ECO 240W 24V 10A, the mid-size ECO unit for full PLC panels. It supplies 240 W / 10 A at 24 V DC from a wide-range AC or DC input, in a corrosion-resistant metal case for TS 35 rail. The data sheet marks it as an article that will no longer be available in future and names PRO ECO 240W 24V 10A II as the alternative, so this page is relevant for maintenance of existing installations and for projects that must match installed units. Seven Star LLC supplies 1469490000 in Oman and the GCC as an independent supplier in Muscat.

At 10 A the unit covers a typical machine or skid panel with controller, remote I/O, HMI and valve coils. It is 60 mm wide, the same width as the 240 W units in the PRO MAX line, so cabinet layouts can often be reused.

What the PRO ECO 240W 24V 10A name tells you

Technical specifications for 1469490000

How the 1469490000 protects itself and the load

The ECO line carries overload, short-circuit and over-temperature protection, plus protection against reverse voltage fed back from the load. A front potentiometer sets the output between 22 V and 28 V. Three LEDs and a floating contact report the state: green when the output voltage is above 21.6 V, yellow when the output current is above 90 percent of rated, and red for overload, over-temperature, short circuit or output voltage below 20.4 V.

On the input side the datasheet gives 85–264 V AC (derating at for AC and 80–370 V DC (Derating @ for DC, with derating at the low end of both windows, a varistor for surge protection and an internal input fuse. Recommended external protection is a safety fuse or a circuit breaker as listed in the data sheet. Harmonic mains currents are limited according to EN 61000-3-2.

Sizing PRO ECO 240W 24V 10A against your load

Efficiency of 90% means the supply wastes 24 W at full load, which is the heat your cabinet must remove; idle loss is 2W. The nominal current is specified at 55 °C, and the continuous rating falls at higher ambient temperature, so use the derating information in the data sheet rather than assuming full power at 70 °C. The unit bridges mains failures for the time stated in the data sheet, which keeps a PLC alive through short dips. Paralleling is allowed as stated in the table, mainly for redundancy.

Related parts and successors for 1469490000

The ECO line comes in three 24 V sizes: 1469480000 (120 W), 1469490000 (240 W) and 1469510000 (480 W). The data sheet names the II versions of each as alternatives. For higher-end requirements, Weidmuller lists the PRO MAX series, for example 1478110000, 1478130000 and 1478140000. For a compact 72 W need, 3076350000 (PRO QL) is a different design. Check dimensions before replacing one model with another, because depth and height differ between lines.

Selection checklist for 1469490000

• Confirm that your load, with start-up peaks, fits within 10 A at the cabinet temperature.
• Check the supply voltage at site against the 85–264 V AC (derating at window.
• Confirm that 60 mm of width is available (100 mm deep).
• Decide whether the successor model is acceptable for the project or if the same type is required.
• Check whether the floating alarm contact will be used.

Installation and maintenance of the PRO ECO 240W 24V 10A

Mount the unit on TS 35 rail, keeping the ventilation slots clear. Input terminals take up to 6 mm² rigid at 0.6 Nm maximum torque; output terminals take 6 mm² rigid and 2.5 mm² flexible. Check output voltage under load at commissioning and log it, then retighten the terminals after the first thermal cycles.

Typical applications in Oman and the GCC

Typical uses in the Gulf include utility skids, HVAC and chiller controls, packaged compressors and general plant control panels, where the supply must run reliably in a warm cabinet but advanced boost features are not required.

Information to send with an RFQ for 1469490000

• Exact order number 1469490000 (PRO ECO 240W 24V 10A) and the quantity, including spares or packs.
• Required output voltage and the continuous and peak load.
• Supply voltage at site and any DC feed.
• Whether the successor model is acceptable as a replacement.
• Delivery location (Muscat, Sohar, Salalah or elsewhere in the GCC) and the date you need the goods.
• Any documents you need with the quotation, such as the datasheet or a compliance statement.

Documents and quotation

The manufacturer data sheet for 1469490000 is attached on this page. It lists the ordering data, approvals, ratings and drawings, so please check its notes against your design before you order.

To request a quotation, send order number 1469490000, the quantity and your delivery location. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer; we will confirm availability and lead time for your order.