- Automation & ControlView all 2,895 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- Pneumatic Cylinders
- HMI Displays
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: ifm
ifm SD8000 Compressed Air Meter, R 1 DN25, IO-Link
Description
ifm SD8000 overview
The ifm SD8000 is the DN25 compressed air meter of the range, with an R 1 external thread. It is listed in the datasheet as a phase-out article with the SD8500 named as the alternative. It measures up to 3750 l/min and combines flow, consumption and temperature monitoring with two switching outputs, an analogue output and IO-Link. Ordering description: SDR11DGXFPKG/US-100.
Status note: in the manufacturer datasheet the SD8000 is listed by the manufacturer as a phase-out article, with the SD8500 named as the alternative article. The datasheet adds that when an alternative article is chosen, its technical data may differ, so engineers should compare the new data sheet before replacing an installed unit. This page describes the SD8000 as documented in that datasheet; ask us about current availability when you send the RFQ.
Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. We list this device so that maintenance, procurement and project teams can quote the exact part number against the manufacturer data.
Key features of the SD8000
- Measuring range 13 to 3750 l/min, equal to 0.4 to 109.2 m/s or 0.7 to 225 cubic metres per hour.
- Pressure rating 16 bar, medium temperature 0 to 60 degrees Celsius.
- Four-digit display, IP 65 housing, 18 to 30 V DC supply.
- Temperature accuracy plus or minus 2 K, as listed.
- Switching, analogue 4 to 20 mA scalable, pulse and IO-Link outputs.
SD8000 technical specifications
| Parameter | Value from the manufacturer datasheet |
|---|---|
| Number of inputs and outputs | Number of digital outputs: 2; Number of analogue outputs: 1 |
| Measuring range | 13…3750 l/min 0.4…109.2 m/s 0.7…225 m³/h |
| Process connection | threaded connection R 1 external thread DN25 |
| Application | for industrial applications |
| Media | compressed air |
| Note on media | air quality ISO 8573-1 |
| Medium temperature [°C] | 0…60 |
| Pressure rating | 16 bar 1.6 MPa |
| Operating voltage [V] | 18…30 DC; (to SELV/PELV) |
| Current consumption [mA] | less than 110 |
| Min. insulation resistance [MΩ] | 100; (500 V DC) |
| Protection class | III |
| Reverse polarity protection | yes |
| Power-on delay time [s] | 1 |
| Total number of outputs | 2 |
| Output signal | switching signal; analogue signal; pulse signal; IO-Link; (configurable) |
| Electrical design | PNP |
| Number of digital outputs | 2 |
| Output function | normally open / normally closed; (parameterisable) |
| Number of analogue outputs | 1 |
| Analogue current output [mA] | 4…20; (scalable) |
| Max. load [Ω] | 500 |
| Pulse output | consumed quantity meter |
| Short-circuit protection | yes |
| Overload protection | yes |
| Display range | 0…4500 l/min 0…131 m/s 0…270 m³/h |
| Set point SP | 30…3750 l/min 0.9…109.2 m/s 1.8…225 m³/h |
| Reset point rP | 12…3732 l/min 0.4…108.7 m/s 0.7…223.9 m³/h |
| Analogue start point ASP | 0…2813 l/min 0…81.9 m/s 0…168.8 m³/h |
| Analogue end point AEP | 937…3750 l/min 27.3…109.2 m/s 56.2…225 m³/h |
| In steps of | 1 l/min 0.1 m/s 0.1 m³/h |
| Pulse value | 0.003…3000000 m³ |
| Pulse length [s] | 0,02…2 |
| Measuring range [°C] | 0…60 |
| Display range [°C] | -12…72 |
| Accuracy (in the measuring | ± (3 % MW + 0,3 % MEW) / ± (6 % MW + 0,6 % MEW); (class 141 /; class) |
| range) | 344; conditions: installation to DIN ISO 2533; installation in pipes: DN25) |
| Accuracy [K] | ± 2; (medium flow in the limit area of the flow measurement range) |
| Response time [s] | 0.1; (dAP = 0) |
| Parameter setting options | Flow monitoring; quantity meter; Preset counter; Temperature monitoring; |
| Communication interface | IO-Link |
| Transmission type | COM2 (38,4 kBaud) |
| IO-Link revision | 1.1 |
| SDCI standard | IEC 61131-9 CDV |
| SIO mode | yes |
| Required master port type | A |
| Process data analogue | 3 |
| Process data binary | 2 |
All values above are taken from the manufacturer datasheet for the SD8000. Ranges are written with three dots, for example 18…30 means 18 to 30. Where a limit depends on the medium or the installation, the datasheet condition applies.
Typical applications in oil and gas, utilities, water and manufacturing
Compressed air is a costly utility in oil and gas plants, power stations and manufacturing sites across Oman and the GCC. A compressed air meter at each branch lets maintenance teams allocate consumption, spot leaks by comparing night and day flow, and verify compressor performance. Instrument air headers, plant air rings and workshop air networks are typical measuring points.
In Oman and the wider GCC, compressed air metering devices like the SD8000 are found in consumption allocation, leak surveys and compressor performance checks. Hot ambient conditions, dust and long cable runs make a sensor with clear local indication and stable outputs valuable, because it shortens fault finding for the shift technician. Check the ambient and medium temperature limits in the table above against the actual site conditions before selecting the device.
Selection and compatibility notes for the SD8000
Because the SD8000 is flagged as phase-out, many sites are looking for exact spares. Compare against the SD8500 on the manufacturer’s page before substituting, since the datasheet states technical data may differ. Match the R 1 thread and the DN25 pipe size, and follow the inlet and outlet run recommendations in the operating instructions.
When you match this device to an existing loop, compare the supply voltage, output type, connector and process connection with the installed device, and confirm that the control system input accepts the signal. Because the part number identifies one exact version in the family, a similar-looking sibling can differ in output polarity, range or thread, and it is better to quote the exact designation than a family name.
Installation and commissioning
Mount the meter in a straight pipe run with the arrow on the housing in the flow direction and the sensing element in the centre of the pipe. Depressurise the line before fitting, use the specified thread sealing method, and keep the inlet and outlet runs given in the operating instructions. Set the scaling, pulse value and switching limits during commissioning, and reset the quantity counter only after recording the starting reading.
Before power-up, check the wiring against the connection diagram in the datasheet, and after power-up allow any start-up delay listed in the table to elapse before judging the output. Document the settings made on site together with the serial number so that a replacement can be configured identically.
Maintenance and service
Keep the compressed air dry and filtered to the quality class assumed in the accuracy statement, because oil or water carry-over can foul the sensing element. Read the totaliser periodically and compare it against compressor load hours, which is the quickest check that the meter and the plant still agree.
Related products and ordering notes
Related ifm devices already listed in the Seven Star catalogue can be found through the brand page. When you request this device, please state the quantity, the required delivery location and whether a datasheet copy is needed. If the application is critical, tell us the process medium, pressure and temperature so the engineer can check the data before the quotation is prepared.
Frequently asked questions
- What is the ifm SD8000? The ifm SD8000 is a compressed air flow meter with a DN25 R 1 thread, listed as a phase-out article. The ifm SD8000 is the DN25 compressed air meter of the range, with an R 1 external thread.
- What supply and protection rating does the SD8000 have? According to the manufacturer datasheet the SD8000 operates from 18…30 DC; (to SELV/PELV) and has protection III.
- Is the SD8000 still available from the manufacturer? The datasheet marks the SD8000 as a phase-out article and names the SD8500 as the alternative. Compare the data sheets before replacing it.
- Does Seven Star LLC supply the SD8000 in Oman? Yes, Seven Star LLC quotes the SD8000 for projects and maintenance in Oman and the GCC. Send the part number SD8000 and the quantity and we will respond with availability.
- How do I get a quotation for the SD8000? Use the RFQ form on this page with the part number SD8000, the quantity and your delivery location. We will reply with a quotation after checking availability.
Documents and quotation
The manufacturer datasheet is attached to this page where the file is available, and it is the reference for every value shown here. To order, send the RFQ with part number SD8000 and the quantity required, together with the delivery location and any application details. Our team will confirm availability and respond with a quotation.
Datasheets & Documents
- Datasheet ifm SD8000 Compressed Air Meter, R 1 DN25, IO-Link Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.
Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.
ifm company profile
| Founded | 1969, Essen, Germany |
|---|---|
| Founders | Robert Buck and Gerd Marhofer |
| Headquarters | Essen, Germany |
| Ownership | Family-owned |
| Product families | Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters |
Milestones
- 1969: ifm is founded in Essen.
- 2001: The founders' sons take over management.
ifm sensors listed on this page
ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:
- O1D100: laser distance sensor for position and distance measurement
- PN7093: pressure sensor with local display
- NG5021: inductive proximity sensor with NAMUR output
Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.
ifm products we list
Ordering ifm sensors: what we need
Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.
Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.
Browse ifm products by category: Sensors & Transmitters, Pressure Instrumentation.
FAQ
Questions about the ifm SD8000 Compressed Air Meter, R 1 DN25, IO-Link
Answers from our engineering team on installation, compatibility and integration.
01What is the ifm SD8000?
The ifm SD8000 is a compressed air flow meter with a DN25 R 1 thread, listed as a phase-out article. The ifm SD8000 is the DN25 compressed air meter of the range, with an R 1 external thread.
02What supply and protection rating does the SD8000 have?
According to the manufacturer datasheet the SD8000 operates from 18...30 DC; (to SELV/PELV) and has protection III.
03Is the SD8000 still available from the manufacturer?
The datasheet marks the SD8000 as a phase-out article and names the SD8500 as the alternative. Compare the data sheets before replacing it.
04Does Seven Star LLC supply the SD8000 in Oman?
Yes, Seven Star LLC quotes the SD8000 for projects and maintenance in Oman and the GCC. Send the part number SD8000 and the quantity and we will respond with availability.
05How do I get a quotation for the SD8000?
Use the RFQ form on this page with the part number SD8000, the quantity and your delivery location. We will reply with a quotation after checking availability.


















Reviews
There are no reviews yet.